Abstract
The use of cutters with replaceable inserts in rotary crushers for the disposal of polymer construction materials is considered. High-speed steel inserts are proposed. The cutter strength is calculated, and the cutting materials undergo ultrajet water–polymer diagnostics.
Similar content being viewed by others
REFERENCES
Kablov, E.N., Modern materials as the basis for innovative modernization of Russia, Met. Evrazii, 2012, no. 3, pp. 10–15.
Nelyub, V.A., The use of polymer composite materials in shipbuilding for the reparation of ship constructions, Remont, Vosstanov., Modernizatsiya, 2013, no. 5, pp. 21–24.
Timoshkov, P.N., Khrul’kov, A.V., and Yazvenko, L.N., Composite materials in the automotive industry (review), Tr. Vseross. Nauchno-Issled. Inst. Aviats. Mater., 2017, no. 6 (54), pp. 61–68.
Doriomedov, M.S., Russian and global markets of polymer composites: a review, Tr. Vseross. Nauchno-Issled. Inst. Aviats. Mater., 2020, nos. 6–7 (89), pp. 29–37.
Kablov, E.N., Strategic plans for development of the materials and their utilization technologies until 2030, Aviats. Mater. Tekhnol., 2012, suppl., pp. 7–17.
Petrov, A.V., Doriomedov, M.S., and Skripachev, S.Yu., Technologies for recycling of polymer composite materials (review), Tr. Vseross. Nauchno-Issled. Inst. Aviats. Mater., 2015, no. 8, art. 9. http://www.viam-works.ru. https://doi.org/10.18577/2307-6046-2015-0-8-9-9
Alifanov, A.V., Burnosov, N.V., Milyukova, A.M., and Tsuran, V.V., Recommendations for the selection of materials for chipper cutters, Tr. Bel. Gos. Tekhnol. Univ., Ser. 2: Lesn. Derevoobrab. Prom-st’, 2014, no. 2, pp. 185–187.
Gogol’, E.V., Mingazetdinov, I.Kh., Gumerova, G.I., et al., Analysis of existing methods of disposal and recycling of polymer wastes, Vestn. Kazan. Tekhnol. Univ., 2013, vol. 16, no. 10, pp. 163–168.
Kravchenko, I.N., Gladkov, V.Yu., Kolomeichenko, A.V., et al., Utilizatsiya i retsikling tekhniki v agropromyshlennom komplekse (Utilization and Recycling of Machines in Agroindustrial Complex), Kravchenko, I.N., Ed., Moscow: Bibkom, 2016.
Korotkov, Yu.V., Tekhnologiya skleivaniya i raschet kleevykh soedinenii rezhushchego instrumenta (Glueing Technology and Calculation of Adhesive Joints of Cutting Tools), Moscow: Vses. Nauchno-Issled. Instrum. Inst., 1982.
Korotkov, Yu.V., Raschet, konstruktsiya, tekhnologiya izgotovleniya i organizatsiya vnedreniya kleevogo rezhushchego instrumenta (Calculation, Design, Manufacturing Technology and Introduction of Adhesive Cutting Tools), Moscow: Vses. Nauchno-Issled. Inst. Mashinostr., 1983.
Barzov, A.A. and Arinchev, P.I., Issledovanie dinamicheskikh svoistv kleenykh rezhushchikh instrumentov (The Dynamic Properties of Glued Cutting Tools), Moscow: Mashinostroenie, 1984.
Bochkarev, S.V., Barzov, A.A., and Galinovskii, A.L., Use of ultrajet diagnostics for quality control of composite materials, Vse Mater., 2020, no. 10, pp. 19–25.
Barzov, A.A., Galinovskiy, A.L., Golubev, E.S., and Filimonov, A.S., Ultrajet diagnostics of the structural and anisotropic features of the parts fabricated by selective laser melting, Russ. Metall. (Engl. Transl.), 2021, vol. 2021, no. 6, pp. 794–800.
Li, S., Galinovskii, Abashin, M.I., and Kravchenko, I.N., Advanced design and diagnostic of tools for utilization of composites, Fundam. Prikl. Probl. Tekh. Tekhnol., 2020, no. 4-2 (342), pp. 23–32.
Galinovskii, A.L., Kravchenko, I.N., Abashin, M.I., Li, S., and Tadzhibov, T.M., RF Patent 203903, 2021.
Funding
Financial support was provided by the Russian Foundation for Basic Research (grant 18-29-18081).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by B. Gilbert
About this article
Cite this article
Xueyan Li, Galinovskii, A.L., Kravchenko, I.N. et al. Replaceable Cutting Inserts for Rotary Crushers. Russ. Engin. Res. 41, 1060–1064 (2021). https://doi.org/10.3103/S1068798X21110265
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X21110265