Skip to main content
SpringerLink
Log in

Innovative Assembly and Welding of Large Aluminum-Alloy Freight-Car Components

  • Published:
Russian Engineering Research Aims and scope

Abstract

Developments in the assembly and welding of large railroad-car components are considered. The introduction of a new aluminum-alloy freight-car body is discussed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.

Similar content being viewed by others

REFERENCES

  1. Mitin, E.V., Sul’din, S.P., and Kalyakulin, S.Yu., Vortex head for thread cutting, Russ. Eng. Res., 2020, vol. 40, no. 12, pp. 1091–1093.

    Article  Google Scholar 

  2. Mitin, E.V., Sul’din, S.P., and Kalyakulin, S.Yu., Strength calculation of a general-purpose light trailer in the starting and turning modes, Avtom. Prom-st’., 2019, no. 3, pp. 33–36.

  3. Sul’din, S.P., Mitin, E.V., and Kalyakulin, S.Yu., Strength calculation of a general-purpose light trailer loaded with stacked cargo, operating in the starting and turning modes, Avtom. Sovrem. Tekhnol., 2019, vol. 73, no. 4, pp. 169–171.

    Google Scholar 

  4. Grigor’ev, A., Loginova, O., Sul’din, S., et al., Strength analysis of a tank-car boiler construction using SolidWorks Simulation software, SAPR Graf., 2019, no. 1 (267), pp. 55–58.

  5. Kalyakulin, S.Yu., Kuz’min, V.V., Mitin, E.V., et al., Development of a mathematical model of a part based on graphic systems models, Inzh. Tekhnol. Sist., 2019, vol. 29, no. 1, pp. 67–76.

    Google Scholar 

  6. Mitin, E.V., Sul’din, S.P., Grigor’ev, A.V., and Okunev, D.V., Design of helical drills with channels for coolant supply, Stanki Instrum., 2019, no. 1, pp. 25–27.

  7. Mitin, E.V., Sul’din, S.P., Grigor’ev, A.V., and Okunev, D.V., Design of helical drills with channels for coolant supply, Russ. Eng. Res., 2019, vol. 39, no. 6, pp. 520–522.

    Article  Google Scholar 

  8. Mitin, E.V. and Sul’din, S.P., Hob strength in gear cutting, Stanki Instrum., 2018, no. 2, pp. 24–27.

  9. Mitin, E.V. and Sul’din, S.P., Hob strength in gear cutting, Russ. Eng. Res., 2018, vol. 38, no. 8, pp. 635–637.

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Ogarev Mordovia State University, Saransk, Russia

    E. V. Mitin & S. P. Sul’din

  2. Evsev’ev Mordovia State Pedagogical University, Saransk, Russia

    A. E. Mitina

Authors
  1. E. V. Mitin
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. P. Sul’din
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. E. Mitina
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to E. V. Mitin or A. E. Mitina.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Mitin, E.V., Sul’din, S.P. & Mitina, A.E. Innovative Assembly and Welding of Large Aluminum-Alloy Freight-Car Components. Russ. Engin. Res. 41, 948–951 (2021). https://doi.org/10.3103/S1068798X21100208

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X21100208

Keywords:

Search

Navigation