Skip to main content
SpringerLink
Log in

Software for Simulation of Low-Speed Machining

  • Published:
Russian Engineering Research Aims and scope

Abstract

Software for the simulation of low-speed machining based on the SolidWorks and Deform-3D CAD/CAE systems is analyzed. The following properties are established: the optimal finite-element size; the influence of epilam nanofilms on thermal processes in different machining conditions; and the influence of the frictional force on the stress at the tool’s working contact surface.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.

Similar content being viewed by others

REFERENCES

  1. Kirichek, A.V. and Zvyagina, E.A., The effect of epilamization on increasing the durability of an axial tool, Uprochnyayushchie Tekhnol. Pokryatiya, 2007, no. 1 (25), pp. 30–35.

  2. Kirichek, A.V. and Selemenev, M.F., Use of epilam nanofilms to improve the efficiency of machining and tool strength, Nanoinzheneriya, 2012, no. 5 (11), pp. 7–14.

  3. Kirichek, A.V., Selemenev, M.F., and Selemeneva, O.V., Effect of epilams (surfactants) on the physical and technical properties of tools at low-speed machining, Fundam. Prikl. Probl. Tekhn. Tekhnol., 2017, no. 2 (322), pp. 85–96.

  4. Vokhidov, A.S., Epilam multifunctional nanosized protective films: synergy effect of antiadhesive and anti-frictional properties, Int. J. Nanotechnol., 2018, vol. 15, nos. 4–5, pp. 417–421.

    Article  Google Scholar 

  5. Vodin, D.V., The use of nanocoatings to increase the durability of cutting tools and the main methods of their application, Avtom. Proekt. Mashinostr., 2014, no. 2, pp. 67–68.

  6. Selemenev, M.F., Velichko, S.A., Kravchenko, I.N., et al., Coatings to improve hole production by mandrels, Russ. Eng. Res., 2021, vol. 41, no. 3, pp. 269–271.

    Article  Google Scholar 

  7. Kireinov, A.V. and Esov, V.B., Modern trends in the use of lubricating and cooling technological means during blade machining of refractory materials, Inzh. Zh.: Nauka Innovatsii, 2017, no. 2 (62). https://doi.org/10.18698/2308-6033-2017-2-1591

  8. Khudobin, L.V., Babichev, A.P., and Bulyzhev, E.M., Smazochno-okhlazhdayushchie tekhnologicheskie sredstva i ikh primenenie pri obrabotke rezaniem: Spravochnik (Lubricating and Cooling Technological Means and Their Use for Cutting: Handbook), Khudobin, L.V., Ed., Moscow: Mashinostroenie, 2006.

    Google Scholar 

  9. Kirichek, A.V., Selemenev, M.F., Selemenev, K.F., et al., Simulation of technological processes of cutting and rolling of threads in SAE systems (DEFORM-3D), Fundam. Prikl. Probl. Tekhn. Tekhnol., 2010, no. 5 (283), pp. 35–38.

  10. Katyshev, S.I., Application of the DEFORM-3D software package for modeling of milling, Materialy XXI Mezhdunarodnoi zaochnoi nauchno-prakticheskoi konferentsii “Eksperimental’nye i teoreticheskie issledovaniya v sovremennoi nauke” (Proc. XXI Int. Extramural Sci.-Pract. Conf. “Modern Experimental and Theoretical Scientific Studies”), Novosibirsk: Sib. Akad. Kniga, 2018, pp. 14–22.

  11. Novikov, A.D., Tarapanov, A.S., and Selemenev, M.F., The dynamics of stress state and temperature in the area of forming of thread rolling, Sovrem. Mater., Tekhn. Tekhnol., 2019, no. 1 (22), pp. 39–44.

  12. Gorbunov, I.V., Efremenkov, I.V., Lent’ev, V.L., and Gismetulin, A.R., Modeling of machining operations in SAE systems, Izv. Samar. Nauchn Tsentra, Ross. Akad. Nauk, 2013, vol. 15, no. 4 (4), pp. 846–853.

  13. Gismetulin, A.R., Gorbunov, I.V., and Efremenkov, I.V., Development of a preprocessor for simulation of machining operations in the LS-DYNA SAE system, Izv. Samar. Nauchn Tsentra, Ross. Akad. Nauk, 2014, vol. 16, no. 1 (5), pp. 1338–1342.

  14. Novoselova, Yu.I., Paukov, A.M., Sheryshev, M.A., et al., 3D modeling in CAD systems by the example of modeling in SolidWorks software, Usp. Khim. Khim. Tekhnol., 2018, vol. 32, no. 6 (202), pp. 120–122.

  15. Zinov’ev, D.V., Osnovy modelirovaniya v SolidWorks (Modeling Principles in SolidWorks), Azanov, M.I., Ed., Moscow: DMK Press, 2017.

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Turgenev Orel State University, Orel, Russia

    M. F. Selemenev, E. A. Prosolov & E. M. Selemeneva

  2. Russian State Agrarian University–Timiryazev Moscow Agricultural Academy, Moscow, Russia

    I. N. Kravchenko

  3. Parakhin Orel State Agrarian University, Orel, Russia

    Yu. A. Kuznetsov

  4. Ogarev Mordovia State University, Saransk, Russia

    S. A. Velichko

  5. Blagonravov Institute of Mechanical Engineering, Russian Academy of Sciences, Moscow, Russia

    M. N. Erofeev

  6. MIREA Russian Technological University, Moscow, Russia

    T. N. Borovik

Authors
  1. M. F. Selemenev
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. I. N. Kravchenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Yu. A. Kuznetsov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. S. A. Velichko
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. M. N. Erofeev
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. T. N. Borovik
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. E. A. Prosolov
    View author publications

    You can also search for this author in PubMed Google Scholar

  8. E. M. Selemeneva
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to I. N. Kravchenko.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Selemenev, M.F., Kravchenko, I.N., Kuznetsov, Y.A. et al. Software for Simulation of Low-Speed Machining. Russ. Engin. Res. 41, 832–835 (2021). https://doi.org/10.3103/S1068798X21090240

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X21090240

Keywords:

Search

Navigation