Skip to main content
SpringerLink
Log in

Stamping of Nonuniform Channels. 2. Theoretical Analyses of Nonuniform-Channel Extrusion: A Review

  • Published:
Russian Engineering Research Aims and scope

Abstract

Theoretical analyses of extrusion are reviewed in the case where the punch and matrix are misaligned. It is found that the formulas obtained do not permit successful design of extrusion processes.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.
Fig. 7.

Similar content being viewed by others

REFERENCES

  1. Vorontsov, A.L., Stamping of nonuniform channels. 1. Comparison of methods of channel production, Russ. Eng. Res., 2021, vol. 41, no. 4, pp. 308–311.

    Article  Google Scholar 

  2. Vorontsov, A.L., Teoriya shtampovki vydavlivaniem (Theory of Extrusive Stamping), Moscow: Mashinostroenie, 2004.

  3. Vorontsov, A.L., The mechanics of a deformable solid and its technological applications. 9. The deformation degree and accumulated deformation. Deformed state of the billet and hardening during upsetting and indentation into the semi-space, Part 1, Proizvod. Prokata, 2011, no. 2, pp. 41–48.

  4. Vorontsov, A.L., Teoriya i raschety protsessov obrabotki metallov davleniem (Theory and Calculations of Metal Forming by Pressure), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2014, vol. 1.

  5. Vorontsov, A.L., The mechanics of a deformable solid and its technological applications. 5. Extreme principles and verification of theoretical studies of metal pressure forming, Proizvod. Prokata, 2010, no. 7, pp. 3–13.

  6. Vorontsov, A.L., The mechanics of a deformable solid and its technological applications. 6. The application of the plasticity theory to the analysis of metal pressure, Proizvod. Prokata, 2010, no. 8, pp. 2–12.

  7. Prozorov. L.V., Cold extrusion of thin-walled products, in Novye issledovaniya v oblasti kuznechnoi tekhnologii (New Studies in Forging Technology), Moscow: Mashgiz, 1950, book 32, pp. 87–96.

  8. Kudo, H., An upper-bound approach to plane-strain forging and extrusion—II, Int. J. Mech. Sci., 1960, vol. 1, nos. 2–3, pp. 229–252.

    Article  Google Scholar 

  9. Evstratov, V.A., Kulikov, I.V., and Ivanov, O.M., Influence of tool misalignment on the character of deformation, power mode, and loads affecting the punch during extrusion, Vestn. Khar’k. Politekh. Inst., 1977, no. 131, pp. 38–44.

  10. Kulikov, I.V., The influence of backpressure on the form change and force mode during flat asymmetric extrusion, Vestn. Khar’k. Politekh. Inst., 1977, no. 131, pp. 45–48.

  11. Evstratov, V.A., Kirillov, G.I., and Chegrinets, O.A., Extrusion of the parts such as glasses in conditions of misalignment of the tool, Vestn. Khar’k. Politekh. Inst., 1985, no. 225, pp. 49–51.

  12. Kravtsova, F.O., Deformed state of a billet during asymmetric piercing, Izv. Vyssh. Uchebn. Zaved., Mashinostr., 1986, no. 2, pp. 137–142.

  13. Evstratov, V.A., Analysis of the force mode of extrusion of parts such as glasses in conditions of misaligned arrangement of the tool, Vestn. Khar’k. Politekh. Inst., 1988, no. 261, pp. 53–56.

  14. Semenov, E.I. and Snimshchikov, V.E., The influence of the tool deviation from the alignment on the deformation character and technological force during reverse extrusion with a conical punch, Vestn. Mashinostr., 1990, no. 10, pp. 64–66.

  15. Semenov, E.I. and Snimshchikov, V.E., The effects of misalignment of a truncated conical punch and matrix on the flow kinematics and force characteristics during reverse extrusion, Vestn. Mashinostr., 1995, no. 4, pp. 30–32.

  16. Tarnovskii, I.Ya., Pozdeev, A.A., Ganago, O.A., et al., Teoriya obrabotki metallov davleniem (Theory of the Metal Pressuring), Moscow: Metallurgizdat, 1963.

  17. Kholodnaya ob’’emnaya shtampovka: Spravochnik (Cold Bulk Stamping: A Handbook), Navrotskii, G.A., Ed., Moscow: Mashinostroenie,1973.

    Google Scholar 

  18. Kovka i shtampovka: Spravochnik. T. 3. Kholodnaya ob’’emnaya shtampovka (Forging and Stamping: A Handbook, Vol. 3: Cold Bulk Stamping), Navrotskii, G.A., Ed., Moscow: Mashinostroenie, 1987.

Download references

Author information

Authors and Affiliations

  1. Bauman Moscow State Technical University, Moscow, Russia

    A. L. Vorontsov

Authors
  1. A. L. Vorontsov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. L. Vorontsov.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Vorontsov, A.L. Stamping of Nonuniform Channels. 2. Theoretical Analyses of Nonuniform-Channel Extrusion: A Review. Russ. Engin. Res. 41, 410–415 (2021). https://doi.org/10.3103/S1068798X21050269

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X21050269

Keywords:

Search

Navigation