Skip to main content
SpringerLink
Log in

Quality Maintenance in Turning Antifrictional F-4UV20 Composite Plastic

  • Published:
Russian Engineering Research Aims and scope

Abstract

When turning F-4UV20 composite plastic, the influence of its strength, elasticity, and abrasive properties on the cutting processes is studied. High quality is ensured by a lathe cutter with a rear angle of at least 6°, when the cutting depth is 0.5–2 mm, the longitudinal supply is 0.05–0.2 mm/turn (Ra = 2.5–4.5 µm), and the cutting speed is 250–300 m/min, in the presence of water–emulsion working fluid. In this case, the surface roughness obtained corresponds practically to the diameter of the chaotically distributed discrete fibers. In other words, it takes the minimum possible value.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.

Similar content being viewed by others

REFERENCES

  1. Kozyrev, Yu.P. and Sedakova, E.B., Antifrictional nanocomposites based on polymers with a multilayer disperse filler, Russ. Eng. Res., 2011, vol. 31, no. 1, pp. 22–24.

    Article  Google Scholar 

  2. Otmakhov, D.V. and Zakharychev, S.P., Properties of reinforced antifrictional epoxy-fluoroplastic materials, Russ. Eng. Res., 2014, vol. 34, no. 11, pp. 687–690.

    Article  Google Scholar 

  3. Dal’skii, A.M., Kosilova, A.G., Meshcheryakov, R.K., et al., Spravochnik tekhnologa-mashinostroitelya (Handbook of Technologist-Machine Engineer), Moscow: Mashinostroenie, 2001, vol. 2.

  4. Perepelkin, K.E., Armiruyushchie volokna i voloknistye polimernye kompozity (Reinforcing Fibers and Fibrous Polymer Composites), St. Petersburg: Nauchnye Osnovy Tekhnol., 2009.

  5. Belousov, V.E., Modeling of tool interaction power during cutting, Stroit. Mekh. Inzh. Konstr. Sooruzh., 2016, no. 4, pp. 62–68.

Download references

Funding

Financial support was provided by the Russian Ministry of Science and Higher Education (project FSNM-2020-0028).

Author information

Authors and Affiliations

  1. Perm National Research Polytechnic University, Perm, Russia

    D. I. Tokarev, A. A. Drozdov, L. D. Sirotenko, E. V. Matygullina & E. S. Shlykov

Authors
  1. D. I. Tokarev
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. A. Drozdov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. L. D. Sirotenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. E. V. Matygullina
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. E. S. Shlykov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to D. I. Tokarev, A. A. Drozdov, L. D. Sirotenko, E. V. Matygullina or E. S. Shlykov.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Tokarev, D.I., Drozdov, A.A., Sirotenko, L.D. et al. Quality Maintenance in Turning Antifrictional F-4UV20 Composite Plastic. Russ. Engin. Res. 41, 439–441 (2021). https://doi.org/10.3103/S1068798X21050245

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X21050245

Keywords:

Search

Navigation