Skip to main content
SpringerLink
Log in

Selection of Representative Parts in Production Design

  • Published:
Russian Engineering Research Aims and scope

Abstract

The manufacturing efficiency resulting from production design by a reduced program is considered. In a reduced program, the production design is based on a small number of representative parts, rather than all of the parts within the specified program. A method is recommended for dividing the parts corresponding to the specified program into groups and selecting a representative part for each group. The representative part is best chosen as an aggregate part reflecting the maximum characteristics and constraints relevant to all the parts in the group.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.

Similar content being viewed by others

REFERENCES

  1. Egorova, M.E., Osnovy proektirovaniya mashinostroitel’nykh zavodov. Uchebnik dlya mashinostroitel’nykh vuzov (Design Principles of Machine Engineering Plants: Manual for Machine Engineering Higher Education Institutions), Moscow: Vysshaya Shkola, 1969.

  2. Mel’nikov, G.N. and Voronenko, V.P., Proektirovanie mekhanosborochnykh tsekhov: uchebnik dlya studentov mashinostroitel’nykh spetsial’nostei vuzov (Design of Machine Assembly Shops: Manual for Students of Machine Engineering Specialties), Dal’skii, A.M., Ed., Moscow: Mashinostroenie, 1990.

  3. Voronenko, V.P., Solomentsev, Yu.M., and Skhirtladze, A.G., Proektirovanie mashinostroitel’nogo proizvodstva (Designing of Machine Engineering Manufacture), Solomentsev, Yu.M., Ed., Moscow: Drofa, 2006.

    Google Scholar 

  4. Voronenko, V.P., Sedykh, M.I., and Igonov, A.V., Modern automated production at the engineering stage, Materialy XII Mezhdunarodnoi konferentsii “Mashinostroenie: traditsii i innovatsii” (MTI–2019) (Proc. XII Int. Conf. “Machine Engineering: Traditions and Innovations” (MTI–2019)), Moscow: Mosk. Gos. Tekhnol. Univ., Stankin, 2019.

  5. Klassifikator ESKD. Klassy 71–75. Illyustrirovannyi opredelitel’ detalei. Poyasnitel’naya zapiska (Classifier of a Unified System for Design Documentation. Classes 71–75. Illustrated Guide for Identification of the Parts. Explanatory Note). Moscow: Izd. Standartov, 1986.

Download references

Author information

Authors and Affiliations

  1. Mechanical Engineering Research Institute of the Russian Academy of Sciences (IMASH RAN), Moscow, Russia

    B. M. Bazrov & N. A. Rodionova

Authors
  1. B. M. Bazrov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. N. A. Rodionova
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to B. M. Bazrov.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Bazrov, B.M., Rodionova, N.A. Selection of Representative Parts in Production Design. Russ. Engin. Res. 41, 363–366 (2021). https://doi.org/10.3103/S1068798X21040055

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X21040055

Keywords:

Search

Navigation