Abstract
Selection criteria are proposed for instruments used in monitoring the positional and shape error of surfaces, taking account of the corresponding formulas based on indirect measurements. The permissible measurement errors are determined, as well as the limiting errors of the instruments used in monitoring the positional and shape error of surfaces in new engine components at Yaroslavl Motor Plant.
Similar content being viewed by others
REFERENCES
Leonov, O.A., Shkaruba, N.Z., and Vergazova, Yu.G., Determining the tolerances in fitting for joints with interference, Russ. Eng. Res., 2019, vol. 39, no. 7, pp. 554–547.
Erohin, M., Leonov, O., Kataev, Yu., and Vergazova, Yu., Calculation of fits for cylindrical connections with key for reducers in agricultural machinery, Proc. 18th Int. Sci. Conf. “Engineering for Rural Development,” Jelgava, 2019, pp. 469–474.
Erokhin, M.N., Leonov, O.A., Shkaruba, N.Z., et al., Assessing the relative interchangeability in joints with preload, Russ. Eng. Res., 2020, vol. 40, no. 6, pp. 469–472.
Leonov, O.A., Metrologiya, standartizatsiya i sertifikatsiya (Metrology, Standardization, and Certification), Moscow: Kolos, 2009.
Erokhin, M.N., Leonov, O.A., Kataev, Yu.V., and Mel’nikov, O.M., Tightness and leakage in applying reinforced rubber sleeves to shafts, Russ. Eng. Res., 2019, vol. 39, no. 6, pp. 459–462.
Sukhanov, V.A., Deformations and damages of V‑shaped cylinder blocks and improvement of their reparation to increase the post-reparation resource (based on the ZIL-130 engine), Cand. Sci. (Eng.) Dissertation, Moscow: Moscow Inst. Agric. Eng., 1980.
TK 10-05.0001.026-87. Diseli YaMZ-240B, YaMZ-240BM: Tekhnicheskie trebovaniya na kapital’nyi remont (TK 10-05.0001.026-87. Diesels YaMZ-240B, YaMZ-240BM: Technical Requirements for Overhaul), Moscow: Gos. Nauchno-Issled. Tekhnol. Inst. Remonta Ekspl. Trakt. S-kh Mash., 1989.
Leonov, O.A. and Shkaruba, N.Zh., Metrologiya i tekhnicheskie izmereniya (Metrology and Technical Measurements), Moscow: Ross. Gos. Agrar. Univ., Mosk. S-kh. Akad., 2015.
GOST (State Standard) 2.308–2011: Unified System of Design Documentation. Representation of Limits of Forms and Surface Lay-Out on Drawings, Moscow: Standartinform, 2012.
MI 2083-90 GSI. Izmereniya kosvennye. Opredelenie rezul’tatov izmerenii i otsenivanie ikh pograshnostei (MI 2083-90 GSI. Indirect Measurements. Determination of Measurement Results and Estimation of Their Errors), Moscow: Izd. Standartov, 1991.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by B. Gilbert
About this article
Cite this article
Shkaruba, N.Z., Leonov, O.A. Permissible Measurement Error in Monitoring the Shape and Position of Surfaces. Russ. Engin. Res. 41, 211–214 (2021). https://doi.org/10.3103/S1068798X21030175
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X21030175