Abstract
The influence of the operating conditions of ring-shaped bundle force elements made of TiNi alloy on the temperature range of shape-memory effects is considered. By adjusting the mechanical load, the functional mechanisms may be operated in specific temperature intervals.
Similar content being viewed by others
REFERENCES
V’yunenko, Yu.N., Mathematical modeling of deformation processes and technological application of the shape memory effect, Fundam. Probl. Sovrem. Materialoved., 2010, vol. 7, no. 3, pp. 28–31.
V’yunenko, Yu.N., Application of the shape memory effect in the production of layered materials, Materialy Mezhdunarodnogo nauchnogo simpoziuma “Perspektivnye materially i tekhnologii” (Proc. Int. Sci. Symp. “Advanced Materials and Technologies”), Vitebsk: Vitebsk. Gos. Tekh. Univ., 2011, pp. 182–184.
Khusainov, M.A., Popov, S.A., and Malukhina, O.A., Optimization of the geometric parameters of spherical segments made of titanium nickelide shape memory alloys, Tech. Phys., 2015, vol. 60, no. 8, pp. 1150–1156.
Resnina, N.N., Belyaev, S.P., Yaparova, E.N., and Andreev, V.A., The effect of stabilization of martensite in TiNi alloys of various compositions, Materialy konferetsii “Splavy s effektom pamyati formy” (Proc. Conf. “Alloys with Shape Memory Effect”), Chelyabinsk: Chelyab. Gos. Univ., 2018, p. 49.
Ivanova, A.B., Yaparova, E.N., Resnina, N.N., and Belyaev, S.P., The effect of martensite stabilization in the Ti–50.0Ni alloy after cooling under load, Materialy Mezhdunarodnogo simpoziuma “Perspektivnye materialy i tekhnologii” (Proc. Int. Symp. “Advanced Materials and Technologies”), Rubanik, V.V., Ed., Vitebsk: Vitebsk. Gos. Tekh. Univ., 2019, p. 291.
V’yunenko, Yu.N., Analysis of the mechanical characteristics of power elements with shape memory effect, Vestn. Tambov. Gos. Univ., Ser.: Estestv. Tekh. Nauki, 2013, vol. 18, no. 4, pp. 2023–2024.
Kollerov, M.Yu., Gusev, D.E., Gurtovoi, S.I., and Burnaev, A.V., Thermomechanical behavior of titanium nickelide-based alloys at a constant counteraction, Russ. Metall. (Engl. Transl.), 2018, vol. 2018, no. 9, pp. 808–814.
Sibirev, A.V., Belyaev, S.P., and Resnina, N.N., Influence of the maximum thermal cycle temperature on martensitic transformations in the TiNi alloy, Materialy Peterburgskikh chtenii po problemam prochnosti (Proc. Petersburg’s Readings on Strength of Materials), St. Petersburg: S.-Peterb. Gos. Politekh. Univ., 2016, pp. 345–347.
Khusainov, M.A., Volnyanskaya, O.Yu., and Malukhina, O.A., Influence of plastic and heat treatment of the TN-1 alloy on the temperatures of martensitic transformations, Trudy IV Mezhdunarodnogo seminara “Sovremennye problemy prochnosti” (Proc. IV Int. Semin. “Modern Problems of Strength”), Malinin, V.G., Ed., Veliky Novgorod, 2000, vol. 2, pp. 244–248.
Author information
Authors and Affiliations
Corresponding authors
Additional information
Translated by B. Gilbert
About this article
Cite this article
Khlopkov, E.A., Dmitrievskiy, A.A., Pomytkin, S.P. et al. Influence of the Mechanical Load on the Operating Temperature of Ring-Shaped Bundle Force Elements. Russ. Engin. Res. 41, 162–165 (2021). https://doi.org/10.3103/S1068798X2102009X
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X2102009X