Abstract
The cutting of convex–concave conjugate surfaces of a globoid pair with an initial cylindrical gear is considered. Experimental assessment confirms the practical utility of the proposed approach. That permits the manufacture of globoid gears with increased load capacity when the hardness of the contacting surfaces is very different, without the need for globoid mills.
Similar content being viewed by others
REFERENCES
Fedotov, B.F., Dumilin, S.V., Shchegol’kov, N.N., and Belyakov, V.N., Improvement of the cutting technology of modified globoid gears with a localized contact patch, Izv. Mosk. Gos. Tekh. Univ., MAMI, 2014, vol. 2, no. 1 (19), pp. 96–99.
Gudov, E.A., Lagutin, S.A., and Fedotov, B.F., Load capacity of modified globoid gears, Vestn. Nats. Tekh. Univ., KhPI, 2011, no. 29, pp. 41–52.
Sandler, A.I., Lagutin, S.A., and Gudov, E.A., Teoriya i praktika proizvodstva chervyachnykh peredach obshchego vida: Uchebno-prakticheskoe posobie (Theory and Practice of Manufacturing of Worm Gears of General View: Practical Manual), Lagutin, S.A., Ed., Moscow: Infra-Inzheneriya, 2016.
Litvin, F.L., Teoriya zubchatykh zatsepenii (Theory of Gear Coupling), Moscow: Nauka, 1968.
Kudryavtsev, Yu.V., Ulitin, N.I., and Fradkin, E.I., Globoid cutter with higher durability, Stanki Instrum., 1975, no. 5, pp. 17–18.
Sandler, A.I., Lagutin, S.A., and Verkhovskii, A.V., Proizvodstvo chervyachnykh peredach (Production of Worm Gears), Lagutin, S.A., Ed., Moscow: Mashinostroenie, 2008.
Parubets, V.I., Globoid transmissions: state, trends, and prospective development of scientific and technical researches, Reduktory Privody, 2008, no. 1 (7), pp. 76–77.
Krivenko, I.S., Novye tipy chervyachnykh peredach na sudakh (New Types of Worm Gears on Ships), Leningrad: Sudostroenie, 1967.
Zhukov, I.P., Technological and instrumental support of the forming process of the globoid-type gears of new geometry, Cand. Sci. (Eng.) Dissertation, St. Petersburg, 2003.
Parubets, V.I., Globoid transmissions: state, trends and prospective development of scientific and technical researches in Russia, Reduktory Privody, 2006, no. 1 (4), pp. 53–54.
Popov, V.A., The design and technology of gear processing of the globoid transmission with higher stability of the original geometry, Extended Abstract of Cand. Sci. (Eng.) Dissertation, Moscow, 1975.
Sakharov, G.N., Obkatochnye instrumenty (Running Test Tools), Moscow: Mashinostroenie, 1983.
Barantsev, A.S., Aravin, B.P., Golubev, K.B., Klo-chko, V.I., and Smirnov, V.I., USSR Inventor’s Certificate no. 745592, Byull. Izobret., 1980, no. 25.
Pavlov, V.A. and Vinogradov, A.B., Proektirovanie i izgotovlenie globoidnoi peredachi s iskhodnymi tsilindricheskim kolesom (Design and Manufacture of a Globoid Gear with an Original Cylindrical Wheel), Novosibirsk: Sib. Gos. Univ. Putei Soobshch., 2007.
Author information
Authors and Affiliations
Corresponding authors
Additional information
Translated by B. Gilbert
About this article
Cite this article
Mal’ko, L.S., Sutyagin, A.V., Trifanov, I.V. et al. Gear Cutting in a Globoid Pair with an Initial Cylindrical Involute Gear. Russ. Engin. Res. 40, 1087–1090 (2020). https://doi.org/10.3103/S1068798X20120400
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X20120400