Skip to main content
SpringerLink
Log in

Water-Jet Cutting of Fiberglass Sheet

  • Published:
Russian Engineering Research Aims and scope

Abstract

The water-jet cutting of fiberglass is studied experimentally. On that basis, the splitting of the fiberglass sheet is related to the cutting conditions. That permits decrease in fiberglass waste and improvement in product quality.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.

Similar content being viewed by others

REFERENCES

  1. Galinovskii, A.L., Tarasov, V.A., and Elfimov, V.M., Minimization of the technological cost of waterjet cutting taking into account the cost and technological parameters of the machining process, Izv. Vyssh. Uch. Zaved., Mashinostr., 2011, no. 4, pp. 46–54.

  2. Barsukov, G.V. and Mikheev, A.V., The productivity of waterjet cutting taking into account the characteristics of the abrasive grain, Spravochnik. Inzh. Zh., 2008, no. 1, pp. 9–14.

  3. Stepanova, E.Yu., Barsukov, G.V., and Stepanov, Yu.S., Advanced technologies of a new generation for shaping of spatially complex surfaces of high-tech products, Izv. Tul’sk. Gos. Univ., Tekh. Nauki, 2016, no. 8-2, pp. 243–249.

  4. Stepanov, Y.S., Barsukov, G.V., and Bishutin, S.G., Technological fundamentals for efficiency control of hydroabrasive cutting, Procedia Eng., 2016, vol. 150, pp. 717–725.

    Article  Google Scholar 

  5. Barsukov, G.V., Kozhus, O.G., and Zhuravleva, T.A., Increasing of efficiency of environmentally friendly technology of AWJ of a glass fiber plastic, IOP Conf. Ser.: Earth Environ. Sci., 2017, vol. 50, no. 1, art. ID 012001.

  6. Barsukov, G.V., Kozhus, O.G., and Zhuravleva, T.A., Quality of hydroabrasive waterjet cutting machinability, Procedia Eng., 2017, vol. 206, pp. 1034–1038.

    Article  Google Scholar 

  7. Barsukov, G.V., Kozhus, O.G., and Zhuravleva, T.A., Methodics of quality of hydroabrasive waterjet cutting machinability assessment, Proc. 4th Int. Conf. on Industrial Engineering (ICIE 2018), New York: Springer-Verlag, 2018, pp. 1677–1685.

  8. Hashish, M., The waterjet as a tool, Proc. 14th Int. Conf. on Jetting Technology. Brugge, BHR Group Conf. Ser. no. 32, London: Professional Engineering, 1998, no. 32, pp. 1–3.

  9. Barsukov, G.V. and Zhuravleva, T.A., The influence of technological modes of waterjet cutting on the surface layering of fiberglass parts, Fundam. Prikl. Probl. Tekh. Tekhnol., 2013, no. 4 (300), pp. 47–56.

  10. Zhuravleva, T.A., Barsukov, G.V., Korotkii, O.A., and Sidorov, V.B., Development of technological recommendations for waterjet cutting of fiberglass, Radiopromyshlennost’, 2014, no. 4, pp. 153–165.

  11. Barsukov, G.V., Zhuravleva, T.A., and Stepanov, Yu.S., Quality assurance of complex contour waterjet cutting of fiberglass parts, Izv. Tul’sk. Gos. Univ., Tekh. Nauki, 2016, no. 8-2, pp. 235–242.

Download references

Funding

This work was supported by the Russian Science Foundation, grant 20-79-00347.

Author information

Authors and Affiliations

  1. Turgenev Orel State University, 302026, Orel, Russia

    G. V. Barsukov & O. G. Kozhus

  2. Kaluga Branch, Bauman Moscow State Technical University, 248004, Kaluga, Russia

    T. A. Zhuravleva

Authors
  1. G. V. Barsukov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. A. Zhuravleva
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. O. G. Kozhus
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to T. A. Zhuravleva or O. G. Kozhus.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Barsukov, G.V., Zhuravleva, T.A. & Kozhus, O.G. Water-Jet Cutting of Fiberglass Sheet. Russ. Engin. Res. 40, 963–965 (2020). https://doi.org/10.3103/S1068798X20110040

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X20110040

Keywords:

Search

Navigation