Skip to main content
SpringerLink
Log in

Relation between the Programmed and Actual Feed Motions in Internal Grinding

  • Published:
Russian Engineering Research Aims and scope

Abstract

A model is proposed for calculating the actual radial feed in internal grinding on a CNC machine. The model establishes the relation between the actual and programmed feed, as a function of the cutting forces, the elastic deformation of the machining system, the cutting conditions, the wheel–workpiece contact geometry, the wheel characteristics, and other parameters. The model is used to predict the change in radius of the machined hole surface in the workpiece, from the initial to the final value for a specified automatic cycle, in various internal-grinding conditions. The model provides the basis for multiparametric optimization of the grinding cycles in multidimensional control-parameter space.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.

Similar content being viewed by others

REFERENCES

  1. Obshchemashinostroitel’nye normativy rezhimov rezaniya dlya tekhnicheskogo normirovaniya rabot na metallorezhushchikh stankakh. Chast’ 3. Protyazhnye, shlifoval’nye i dovodochnye stanki (General Machine engineering Standards of Cutting Regimes for Technical Standardization of Operations on Metal Cutting Machines, Part 3: Broaching, Grinding, and Finishing Machines), Moscow: Mashinostroenie, 1978.

  2. Ardashev, D.V., Anel’chik, D.E., Butorin, G.I., et al., Rezhimy rezan’ya na raboty, vypolnyaemye na shlifoval’nykh i dovodochnykh stankakh s ruchnym upravleniem i poluavtomatakh (Cutting Regimes for Grinding and Finishing Machines with Manual and Semi-Automatic Control), Chelyabinsk: Atokso, 2007.

  3. Novoselov, Yu.K., Dinamika formoobrazovaniya poverkhnostei pri abrazivnoi obrabotke (Dynamics of Surface Abrasive Shaping), Sevastopol: Sevast. Nats. Tekh. Univ., 2012.

  4. Guzeev, V.I. and Nurkenov, A.K., Researching the CNC-machine stiffness impact on the grinding cycle design, Procedia Eng., 2016, vol. 150, pp. 815–820.

    Article  Google Scholar 

  5. Nishimura, T., Inasaki, I., and Yamamoto, N., Study on optimization of internal grinding cycle, Trans. Jpn. Soc. Mech. Eng., 1989, vol. 55, pp. 1808–18013.

    Article  Google Scholar 

  6. Fomin, A.A., Kinematics of surface formation in milling, Russ. Eng. Res., 2013, vol. 33, no. 11, pp. 660–662.

    Article  Google Scholar 

  7. Pereverzev, P.P. and Akintseva, A.V., Optimal internal grinding cycles in multidimensional control-parameter space, Russ. Eng. Res., 2016, vol. 3636, no. 11, pp. 974–978.

    Article  Google Scholar 

  8. Bellman, R., Dynamic Programming, Princeton, NJ: Princeton Univ. Press, 1957.

    MATH  Google Scholar 

  9. Pereverzev, P.P. and Akintseva, A.V., Modeling of metal removal during an internal grinding in view of kinematics cutting features, Russ. Eng. Res., 2016, vol. 36, no. 10, pp. 888–893.

    Article  Google Scholar 

  10. Pereverzev, P.P. and Akintseva, A.V., Model of formation of processing errors intragrinding, Russ. Eng. Res., 2016, vol. 36, no. 12, pp. 1048–1053.

    Article  Google Scholar 

  11. Pereverzev, P.P. and Pimenov, D.Yu., A grinding force model allowing for dulling of abrasive wheel cutting grains in plunge cylindrical grinding, J. Frict. Wear, 2016, vol. 37, no. 1, pp. 60–65.

    Article  Google Scholar 

  12. Korchak, S.N., Proizvoditel’nost’ protsessa shlifovaniya stal’nykh detalei (Grinding Performance of Steel Parts), Moscow: Mashinostroenie, 1974.

  13. Danilenko, M.V. and Nosenko, V.A., Dynamic probability theory model of cutting force during grinding, Izv. Volgograd. Gos. Tekh. Univ., 2017, no. 12 (207), pp. 31–33.

  14. Pereverzev, P.P. and Popova, A.V., Analytical modeling of the relationship the cutting force at internal grinding with the basic technological factors, Metalloobrabotka, 2013, no. 3, pp. 24–30.

  15. Feodos’ev, V.I., Soprotivlenie materialov (Strength of Materials), Moscow: Nauka, 1979.

Download references

Author information

Authors and Affiliations

  1. South Ural State University, 454080, Chelyabinsk, Russia

    A. V. Akintseva, A. V. Prokhorov, S. V. Omel’chenko & S. N. Kononov

Authors
  1. A. V. Akintseva
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. V. Prokhorov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. V. Omel’chenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. S. N. Kononov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to A. V. Akintseva, A. V. Prokhorov, S. V. Omel’chenko or S. N. Kononov.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Akintseva, A.V., Prokhorov, A.V., Omel’chenko, S.V. et al. Relation between the Programmed and Actual Feed Motions in Internal Grinding. Russ. Engin. Res. 40, 508–513 (2020). https://doi.org/10.3103/S1068798X20060039

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X20060039

Keywords:

Search

Navigation