Skip to main content
SpringerLink
Log in

Fitting Parameters in the Cylindrical Section of Ball-End Mills for Five-Coordinate Machine Tools

  • Published:
Russian Engineering Research Aims and scope

Abstract

The production of the rake surface in different sections of a grinding wheel is considered, with identification of the appropriate fitting parameter. The parameters of the cylindrical section in ball-end mills are plotted against the selected fitting parameter.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.

Similar content being viewed by others

REFERENCES

  1. Ryabov, E.A., Yurasov, S.Yu., and Yurasova, O.I., Parametric modeling of ball end mills, Russ. Eng. Res., 2016, vol. 36, no. 9, pp. 784–785.

    Article  Google Scholar 

  2. Ryabov, E.A., Petrov, S.M., Stupko, V.B., et al., Spherical part of ball end mill with constant tool cutting edge inclination, Int. J. Mech. Prod. Eng. Res. Dev., 2018, vol. 8, no. 8, pp. 450–457.

    Google Scholar 

  3. Ryabov, E.A., Khisamutdinov, R.M., Grechishnikov, V.A., et al., Ball end mill with curved cutting edge and constant cutting geometry, Russ. Eng. Res., 2018, vol. 38, no. 12, pp. 1015–1017

    Article  Google Scholar 

  4. Ryabov, E.A., Khisamutdinov, R.M., and Yurasov, S.Yu., Direction of chip flow for milling of shaped surfaces by ball end mill, IOP Conf. Ser.: Mater. Sci. Eng., 2018, vol. 412, no. 1, art. ID 012060.

  5. Korovin, E.M., Lunyov, A.N., and Khasanov, R.Sh., Optimization of cutting parameters for automatic machines, Russ. Aeronaut., 2006, vol. 49, no. 4, pp. 100–105.

    Google Scholar 

  6. Grechishnikov, V.A., Petukhov, Yu.E., Pivkin, P.M., et al., Trochoidal slot milling, Russ. Eng. Res., 2017, vol. 37, no. 9, pp. 821–823.

    Article  Google Scholar 

  7. Grechishnikov, V.A., Ilyukhin, Yu.V., Isaev, A.V., et al., Increase of accuracy and performance of robotic milling based on trajectory-impedance control, Vestn. Mosk. Gos. Tekhnol. Univ., Stankin, 2016, no. 4 (39), pp. 8–16.

  8. Grigor’ev, S.N., Grechishnikov, V.A., Volosova, M.A., et al., Solid ceramic end milling cutters for hard-to-cut materials machining, Vestn. Mosk. Gos. Tekhnol. Univ., Stankin, 2018, no. 4 (47), pp. 87–93.

  9. Isaev, A.V., Grechishnikov, V.A., Pivkin, P.M., et al., Machining of thin-walled parts produced by additive manufacturing technologies, Procedia CIRP, 2016, vol. 41, pp. 1023–1026.

    Article  Google Scholar 

  10. Grechishnikov, V.A., Isaev, A.V., and Romanov, V.B., Forming method of initial tool surface generatrix of profile milling cutters equipped with cutting inserts positioned along helical line, Vestn. Mosk. Gos. Tekhnol. Univ., Stankin, 2015, no. 1 (32), pp. 8–12.

  11. Grechishnikov, V.A. and Isaev, A.V., Definition of position of the carbide indexable inserts arranged along helical chip flute on body of form milling cutter, Vestn. Mosk. Gos. Tekhnol. Univ., Stankin, 2014, no. 2 (29), pp. 34–39.

  12. Grechishnikov, V.A., Isaev, A.V., et al., Cutting tool solutions for robotic milling, Vestn. Mosk. Gos. Tekhnol. Univ., Stankin, 2017, no. 4 (43), pp. 73–78.

Download references

Author information

Authors and Affiliations

  1. Naberezhnye Chelny Institute, Kazan Federal University, 423812, Naberezhnye Chelny, Russia

    E. A. Ryabov, R. M. Khisamutdinov, S. Yu. Yurasov & Yu. S. Yurasov

  2. Moscow State Technological University “Stankin”, 127055, Moscow, Russia

    Yu. E. Petukhov, A. V. Isaev & P. V. Domnin

  3. Moscow Polytechnic University, 107023, Moscow, Russia

    V. A. Kuznetsov

Authors
  1. E. A. Ryabov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Yu. E. Petukhov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. R. M. Khisamutdinov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. S. Yu. Yurasov
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Yu. S. Yurasov
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. V. A. Kuznetsov
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. A. V. Isaev
    View author publications

    You can also search for this author in PubMed Google Scholar

  8. P. V. Domnin
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to E. A. Ryabov, Yu. E. Petukhov or R. M. Khisamutdinov.

Additional information

Translated by B. Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Ryabov, E.A., Petukhov, Y.E., Khisamutdinov, R.M. et al. Fitting Parameters in the Cylindrical Section of Ball-End Mills for Five-Coordinate Machine Tools. Russ. Engin. Res. 40, 73–75 (2020). https://doi.org/10.3103/S1068798X20010189

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X20010189

Keywords:

Search

Navigation