Abstract—The failure of cutting tools is investigated. A generalized approach to describing failure is proposed, on the basis of the theory of random point processes. Two mechanisms by which the abrasive particles act on the tool’s cutting edge are considered. The corresponding dynamics of damage accumulation is described.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
REFERENCES
Holopov, V., Kushnir, A., Kumasov, E., et al., Development of digital production engineering monitoring system based on equipment state index, Proc. 2017 IEEE Conf. of Russian Young Researchers in Electrical and Electronic Engineering (EIConRus), Piscataway, NJ: Inst. Electr. Electron. Eng., 2017, pp. 863–868. https://doi.org/10.1109/EIConRus.2017.7910692
Kurnasov, E.V., Object attachment of devices in SCADA systems, Russ. Eng. Res., 2013, vol. 33, no. 3, pp. 152–155. https://doi.org/10.3103/S1068798X1303009X
Romanov, M.P., Romanov, A.M., Kashirskaya, E.N., et al., A novel architecture for the executive-level control systems for a discrete machinery production, Mekhatron., Avtom., Upr., 2017, vol. 18, no. 1, pp. 64–72.
Romanov, A., Romanov, M., Kharchenko, A., and Kholopov, V., Unified architecture of execution level hardware and software for discrete machinery manufacturing control systems, Proc. 2016 IEEE Student Conf. on Research and Development (SCOReD), Piscataway, NJ: Inst. Electr. Electron. Eng., 2016, pp. 1–6.
Kashirskaya, E.N., The effect of fatigue stresses on the resistance of a metal-cutting tool, Materialy II Mezhdunarodnoi konferentsii “Aktual’nye problemy mekhaniki sploshnoi sredy” (Proc. II Int. Conf. “Urgent Problems of Mechanics of Solid Media”), Yerevan, 2010, vol. 1, pp. 283–286.
Albagachiev, Yu.A. and Makhmudov, M.A., Modeling of setting during cutting and friction, Vestn. MIREA—Ross. Tekhnol. Univ., 2015, vol. 2, no. 3 (8), pp. 36–41.
Arutyunyan, R.A., Probabilistic methods of solution the fatigue problem, Vestn. Ross. Fonda Fundam. Issled., 2006, no. 2, vol. 46, pp. 45–58.
Kashirskaya, E.N. and Kholopov, V.A., Tool management in multi-item small batch production based on durability adjustment, Vestn. Mosk. Gos. Akad. Priborostr. Inf., 2005, no. 2, pp. 41–47.
Kurnasov, E.V., Design of housing components in NCCAD system, Russ. Eng. Res., 2009, vol. 29, no. 8, pp. 841–847. https://doi.org/10.3103/S1068798X09080218
Kumasov, E.V., Creation of plastic zones and their cross sections in NC CAD equipment, Russ. Eng. Res., 2009, vol. 29, no. 2, pp. 191–193. https://doi.org/10.3103/S1068798X09020178
Funding
Financial support was provided by the Russian Ministry of Education and Science (project identifier PNIER RFMEFI58016X0008).
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by Bernard Gilbert
About this article
Cite this article
Kashirskaya, E.N. Influence of Alternating Stress on the Life of Metal-Cutting Tools. Russ. Engin. Res. 39, 866–868 (2019). https://doi.org/10.3103/S1068798X19100125
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X19100125