Skip to main content
SpringerLink
Log in

Turning of F-4UV20 Composite Plastic

  • Published:
Russian Engineering Research Aims and scope

Abstract

The turning of F-4UV20 composite plastic is investigated. Continuous chip is formed in all the experimental conditions: cutting speed 16–100 m/min; supply 0.05–0.2 mm/turn; cutting depth 0.5–2 mm. The wear of the cutting insert is uniform (0.1 mm at the rear surface and 0.3 mm at the front surface), with no traces of adhesion. After turning, carbon fibers remain on the machined surface, conferring antifrictional properties without significant effect on the roughness.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.

Similar content being viewed by others

REFERENCES

  1. Zubarev, Yu.M., Priemyshev, A.V., and Zaostrovskii, A.S., Blade cutting by cutting of billets from polymer composite materials, Naukoemkie Tekhnol. Mashinostr., 2018, no. 2, pp. 40–47.

  2. Gubbels, G.P.H., Diamond turning of glassy polymers, PhD Thesis, Eindhoven: Tech. Univ. Eindhoven, 2006, pp. 35–39.

  3. Eneyew, E.D. and Ramulu, M., Experimental study of surface quality and damage when drilling unidirectional CFRP composites, J. Mater. Res. Technol., 2014, vol. 3, pp. 354–362.

    Article  Google Scholar 

  4. Ravikanth Raju, P. and Karna Soma Shankar, Optimization of various process parameters for CFRP composite materials machining, J. Mech. Civ. Eng., 2016, vol. 13, no. 6, pp. 35–40.

    Google Scholar 

  5. Xiao, K.Q. and Zhang, L.C., The role of viscous deformation in the machining of polymers, Int. J. Mech. Sci., 2002, vol. 44, nos. 2317–2336, pp. 123–131.

Download references

Author information

Authors and Affiliations

  1. Perm National Research Polytechnic University, Perm, Russia

    T. R. Ablyaz, E. V. Matygullina, L. D. Sirotenko, D. I. Tokarev & A. A. Drozdov

Authors
  1. T. R. Ablyaz
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. E. V. Matygullina
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. L. D. Sirotenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. D. I. Tokarev
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. A. A. Drozdov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to E. V. Matygullina, L. D. Sirotenko, D. I. Tokarev or A. A. Drozdov.

Additional information

Translated by Bernard Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Ablyaz, T.R., Matygullina, E.V., Sirotenko, L.D. et al. Turning of F-4UV20 Composite Plastic. Russ. Engin. Res. 39, 884–885 (2019). https://doi.org/10.3103/S1068798X19100034

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X19100034

Keywords:

Search

Navigation