Abstract
The deformation of a protrusion by a peripheral annular punch is mathematically described. The protrusion is formed as a result of central-punch introduction in the manufacture of large disks or hard-to-deform disks by plastic deformation. The maximum force at the end of deformation is found. The relative radius of the annular punch ensuring equal stamping forces for the central and annular punches is determined.
Similar content being viewed by others
REFERENCES
Vorontsov, A.L., Production of large disks from cylindrical blanks by plastic deformation. 1. Formulation of the problem, Russ. Eng. Res., 2019, vol. 39, no. 6, pp. 477–479.
Vorontsov, A.L., Production of large disks from cylindrical blanks by plastic deformation. 2. The introduction of the central punch at the stage of concavity formation, Vestn. Mashinostr., 2019, no. 4, pp. 54–57.
Vorontsov, A.L., Production of large disks from cylindrical blanks by plastic deformation. 3. The final stage of the introduction of the central punch, Vestn. Mashinostr., 2019, no. 5, pp. 49–52.
Vorontsov, A.L., Analysis of kinematic, stressed, and deformed states of the billet during punching of the cylindrical punching into half space, Vestn. Mashinostr., 1998, no. 7, pp. 44–47.
Vorontsov, A.L., New solution of complex variational problems by the description of the shape change of the blank during firmware, Kuznechno-Shtampovochnoe Proizvod.–Obrab. Mater. Davleniem, 2009, no. 10, pp. 3–8.
Vorontsov, A.L., Teoriya i raschety protsessov obrabotki metallov davleniem (Theory and Calculations of Processing of Metals by Pressure), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2014, vol. 1.
Vorontsov, A.L., Teoriya i raschety protsessov obrabotki metallov davleniem (Theory and Calculations of Processing of Metals by Pressure), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2014, vol. 2.
Vorontsov, A.L., Mechanics of a deformable solid and its technological applications. 7. Axisymmetric problem of the theory of plasticity. Stress and kinematic state with the draft of a cylindrical billet with friction on the ends. Work balance method: Part 1, Proizvod. Prokata, 2010, no. 9, pp. 2–13.
Vorontsov, A.L., Mechanics of a deformable solid and its technological applications. 7. Axisymmetric problem of the theory of plasticity. Stress and kinematic state with the draft of a cylindrical billet with friction on the ends. Work balance method: Part 2, Proizvod. Prokata, 2010, no. 10, pp. 2–14.
Dmitriev, A.M. and Vorontsov, A.L., Friction coefficients for the calculation of extrusion process parameters, Kuznechno-Shtampovochnoe Proizvod.-Obrab. Mater. Davleniem, 2004, no. 1, pp. 23–26.
Semenov, E.I., Kovka i ob”emnaya shtampovka (Forging and Bulk Stamping), Moscow: Vysshaya Shkola, 1972.
Vorontsov, A.L., The approximation of the hardening curves, Proizvod. Prokata, 2001, no. 3, pp. 21–25.
Dmitriev, A.M. and Vorontsov, A.L., Approximation of the hardening curves of metals, Kuznechno-Shtampovochnoe Proizvod.-Obrab. Mater. Davleniem, 2002, no. 6, pp. 16–22.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by Bernard Gilbert
About this article
Cite this article
Vorontsov, A.L. Production of Large Disks from Cylindrical Blanks by Plastic Deformation. 4. Deformation of a Protrusion by an Annular Punch. Russ. Engin. Res. 39, 745–748 (2019). https://doi.org/10.3103/S1068798X19090247
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X19090247