Abstract
A formula for the theoretical tolerance in fitting is derived by analysis of the components in the model of parametric failure for joints with interference. The formula takes account of the life of the joint and the specified probability of fault-free operation. It is found that selection of the fit without a margin of precision does not ensure the necessary reliability of the joint, while correct selection of the margin of precision extends the fault-free operation of the joint.
Similar content being viewed by others
REFERENCES
Erokhin, M.N., Kazantsev, S.P., Mel’nikov, O.M., and Ignatkin, I.Yu., Detali mahsin (Machine Parts), Moscow: Vseross. Nauchno-Issled. Inst. Gidrotekh. Melioratsii im. A.N. Kostyakova, 2016.
Puchin, E.A., Novikov, V.S., Ochkovskii, N.A., et al., Tekhnologiya remonta mashin (Technology of Machine Reparation), Moscow: Kolos, 2007.
Ivanochkin, P.G., Kolesnikov, I.V., and Chelokh’yan, A.V., Iznashivanie nepodvizhnykh soedinenii (fretting-korroziya) (Wear of Fixed Joints (Fretting Corrosion)), Rostov-on-Don: Rostovsk. Gos. Univ. Putei Soobshch., 2001.
Yakushev, A.I., Bezhelukova, E.F., and Plutalov, V.N., Dopuski i posadki ESDP dlya gladkikh tsilindricheksikh detalei (raschet i vybor) (Limits and Fitting from the Unified System of Limits and Fittings for Smooth Cylindrical Parts: Calculation and Selection), Moscow: Izd. Standartov, 1978.
Belov, V.M., Raschet tochnostnykh parameterov sel’skokhozyaistvennoi tekhniki (Calculation of Accuracy Parameters for Agricultural Machines), Moscow: Mosk. Gos. Agroinzh. Univ., 1990.
Leonov, O.A., Vzaimozamenyaemost’ unifitsirovannykh soedinenii pri remonte sel’skokhozyaistvennoi tkehniki: Monografiya (Interchangeability of Unified Joints in Reparation of Agricultural Machines: Monograph), Moscow: Mosk. Gos. Agroinzh. Univ., 2003.
Erokhin, M.N., Relationship of accuracy and reliability of joints in reparation of agricultural machines, Vestn. Mosk. Gos. Agroinzh. Univ., 2006, no. 2, pp. 22–25.
Pronikov, A.S., Parametricheskaya nadezhnost’ mashin (Parametric Reliability of Machines), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2002.
Dunaev, P.F. and Lelikov, O.P., Raschet dopuskov razmerov (Calculation of Size Limits), Moscow: Mashinostroenie, 2001.
Bulatov, V.P., Fridlender, I.G., Batalov, A.P., et al., Raschet tochnosti mahsin i priborov (Calculation of Accuracy of Machines and Devices), Moscow: Politekhnika, 2001.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated by Bernard Gilbert
About this article
Cite this article
Leonov, O.A., Shkaruba, N.Z. & Vergazova, Y.G. Determining the Tolerances in Fitting for Joints with Interference. Russ. Engin. Res. 39, 544–547 (2019). https://doi.org/10.3103/S1068798X19070116
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X19070116