Abstract
The article presents a design for a tool block. The cutters of the tool block are located asymmetrically. Cutters carry out butt-end turning of holes. The tool block has a high durability, makes it possible to produce shallow bores with flat bottoms, increases manufacturing capability and precision, and reduces the form of deviation and asperity of a finished surface.
Similar content being viewed by others
REFERENCES
Granovskii, G.I. and Granovskii, V.G., Rezanie metallov (Metal Cutting), Moscow: Vysshaya Shkola, 1985.
Sakharov, G.I., Arbuzov, O.V., Borovoi, Yu.L., et al., Metallorezhushchie instrumenty (Metal-Cutting Tools), Moscow: Mashinostroenie, 1989.
Sandvik Coromant becomes premium partner of DMG Mori, Manuf. Eng. Mag., 2017, vol. 158, no. 2, pp. 25–25.
Sandvik Coromant becomes new ISTMA global partner, Adv. Mater. Process., 2008, vol. 166, no. 8, pp. 19–19.
Artamonov, V.V., Bykov, A.O., Bykov, P.O., and Artamonov, V.P., Measurement of the tap density of metal powders, Powder Metall. Met. Ceram., 2013, vol. 52, nos. 3–4, pp. 237–239.
Cep, R., Janasek, A., Sliva, A., Neslusan, M., and Binder, M., Experimental tool life tests of indexable inserts for stainless steel machining, Tehn. Vjesn.-Tech. Gaz., 2013, vol. 20, no. 6, pp. 933–940.
Filippov, A.V., Shamarin, N.N., Podgornykh, O.A., and Chazov, P.A., Cross section of the cut layer in oblique single-edge boring by a radial cutter, Russ. Eng. Res., 2017, vol. 37, no. 4, pp. 367–371.
Dudak, N., Taskarina, A., Kasenov, A., Itybaeva, G., et al., Hole machining based on using an incisive built-up reamer, Int. J. Precis. Eng. Manuf., 2017, vol. 18, no. 10, pp. 1425–1432.
Dudak, N.S., Itybaeva, G.T., Musina, Z.K., et al., A new pass-through lathe cutter, Russ. Eng. Res., 2014, vol. 34, no. 11, pp. 705–707.
Borovskii, V.G., Neginskii, E.A., Ott, O.S., and Maslov, A.R., Drilling of hard rock by means of polycrystalline diamond inserts, Russ. Eng. Res., 2018, vol. 38, no. 1, pp. 33–35.
Dudak, N.S., Kasenov, A.Z., Musina, Z.K., et al., Processing of holes with a reamer-broach, Life Sci. J., 2014, vol. 11, no. 10, pp. 282–288.
Berezyuk, V.G., Kuzembayev, S.B., Sherov, K.T., et al., Increase of precision of casting blocks by applying acoustical oscillations in gas-impulsive molding, J. Vibroeng., 2015, vol. 17, no. 5, pp. 2178–2186.
Dudak, N.S. and Tastenov, E.K., KZ Patent 20211, Byull. Izobret., 2008, no. 11.
Dudak, N.S., KZ Patent 22032, Byull. Izobret., 2009, no. 12.
Dudak, N.S. and Yanyushkin, A.S., Method and cutting head for high-performance face turning of holes, Sist., Metody. Tekhnol., 2011, no. 9, pp. 78–86.
Dudak, N.S., Mukanov, R.B., Mendebaev, T.M., et al., Hole machining by assembled cutting head, Vestn. Gos. Univ. im. Shakarima Goroda Semei, 2017, vol. 1, no. 2 (78), pp. 57–61.
Author information
Authors and Affiliations
Corresponding authors
Additional information
The article was translated by the authors.
About this article
Cite this article
Mukanov, R.B., Kasenov, A.Z., Itybaeva, G.T. et al. Face Turning of Holes. Russ. Engin. Res. 39, 75–78 (2019). https://doi.org/10.3103/S1068798X19010064
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X19010064