Skip to main content
SpringerLink
Log in

Control of Surface Quality in High-Speed Machining

  • Published:
Russian Engineering Research Aims and scope

Abstract

Control of the surface quality by decreasing the influence of plastic deformation on the surface roughness is proposed. Analytical formulas are presented for the plastic burring in the cutting of a number of materials. The influence of the cutting speed on the microhardness of the surface layer after high-speed machining is investigated.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.

Similar content being viewed by others

REFERENCES

  1. Nasad, T.G., Kiryushin, I.E., and Kiryushin, D.E., Vysokoskorostnaya obrabotka trudnoobrabatyvaemykh materialov: monografiya (High-Speed Processing of Refractory Materials: Monograf), Saratov: Sarat. Gos. Tekhnol. Univ., 2009.

  2. Kiryushin, D.E., Kiryushin, I.E., and Nasad, T.G., High-speed end milling of titanium alloys, Russ. Eng. Res., 2008, vol. 28, no. 10, pp. 1022–1025.

    Article  Google Scholar 

  3. Nasad, T.G., Surface quality after high-speed processing with heat, Tekhnol. Mashinostr., 2004, no. 3 (27), pp. 11–13.

Download references

Author information

Authors and Affiliations

  1. Gagarin Saratov State Technical University, Saratov, Russia

    T. G. Nasad, A. N. Vasin, A. A. Kazinskii, A. A. Ignat’ev, B. M. Iznairov, G. A. Kozlov, D. A. Tikhonov, E. M. Samoilova, O. P. Reshetnikova, Yu. O. Glushkova, O. Yu. Davidenko & V. A. Melent’ev

Authors
  1. T. G. Nasad
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. N. Vasin
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. A. A. Kazinskii
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. A. A. Ignat’ev
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. B. M. Iznairov
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. G. A. Kozlov
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. D. A. Tikhonov
    View author publications

    You can also search for this author in PubMed Google Scholar

  8. E. M. Samoilova
    View author publications

    You can also search for this author in PubMed Google Scholar

  9. O. P. Reshetnikova
    View author publications

    You can also search for this author in PubMed Google Scholar

  10. Yu. O. Glushkova
    View author publications

    You can also search for this author in PubMed Google Scholar

  11. O. Yu. Davidenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  12. V. A. Melent’ev
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to T. G. Nasad, A. N. Vasin, A. A. Kazinskii or A. A. Ignat’ev.

Additional information

Translated by Bernard Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Nasad, T.G., Vasin, A.N., Kazinskii, A.A. et al. Control of Surface Quality in High-Speed Machining. Russ. Engin. Res. 38, 1077–1079 (2018). https://doi.org/10.3103/S1068798X18120286

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X18120286

Keywords:

Search

Navigation