Skip to main content
SpringerLink
Log in

Laser Machining of Tool Steels

  • Published:
Russian Engineering Research Aims and scope

Abstract

Laser quenching and application of wear-resistant powder to the cutting edge of a hob is considered, with careful positioning of the laser spot. Experimental data are analyzed. The quality of quenching and powder surfacing depends on the machining conditions; the quality of the laser radiation; the energy characteristics of the laser system; and the precision in positioning the laser focus.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.

Similar content being viewed by others

REFERENCES

  1. Zvezdin, V.V., Pesoshin, V.A., Saubanov, R.R., and Rakhimov, R.R., Control of a laser technological complex of tool hardening, Vestn. Chuvash. Gos. Univ., 2016, no. 3, pp. 188–193.

  2. Zvezdin, V.V., Khisamutdinov, R.M., Israfilov, I.Kh., and Rakhimov, R.R., Control of the position of the laser radiation focus during the welding of the teeth of the cutter, Materialy mezhdunarodnoi nauchno-tekhnicheskoi konferentsii “Innovatsionnye mashinostroitel’nye tekhnologii, oborudovanie i materialy” (Proc. Int. Sci.-Tech. Conf. “Innovative Machine Engineering Technologies, Equipment, and Materials”), Kazan, 2016, pp. 72–76.

  3. Chernova, M.A., Khisamutdinov, R.M., Zvezdin, V.V., et al., Metallographic studies of laser deposition of wear-resistant powders on the tool, Fundam. Issled., 2015, no. 114, pp. 753–758.

  4. Zvezdin, V.V., Samorsky, V.V., Pesoshin, V.A., et al., Improvement of combined laser-plasma welding, Izv. Vyssh. Uchebn. Zaved., Fiz.,2015, vol. 58, no. 9–2, pp. 36–39.

  5. Khisamutdinov, R.M., Zvezdin, V.V., and Khisamutdinov, M.R., Laser surfacing of special powders to increase the wear resistance of the teeth of cutter, Mezhdunar. Zh. Prikl. Fundam. Issled., 2017, no. 4–3, pp. 482–485.

  6. Zvezdin, V.V., Israfilov, D.I., Portnov, S.M., et al., Automatic control system of high-precision welding of preparations by the laser radiation at influence of the plasma torch, Izv. Vyssh. Uchebn. Zaved., Fiz., 2015, vol. 58, no. 9-3, pp. 51–54.

  7. Tekhnologicheskie lazery. Tom 1. Raschet, proektirovanie i ekspluatatsiya (Technological Lasers, Vol. 1: Calculation, Design, and Exploitation), Abil’siitov, G.A., Ed., Moscow: Mashinostroenie, 1991.

  8. Zvezdin, V.V., Khamadeev, A.V., Fardiev, R.K., et al., Effect of mode composition of laser radiation on the heat-affected zone in metals, Vestn. Kazan. Gos. Tekh. Univ. im. A.A. Tupoleva, 2007, no. 2, pp. 84–85.

  9. Grechishnikov, V.A., Sedov, B.E., and Romanov, V.B., Proektirovanie diskovoi frezy dlya obrabotki vintovoi kanavki sverla. Metodicheskie ukazaniya dlya vypolneniya kursovoi raboty (Design of a Milling Cutter for Treatment of Helical Groove of a Drill: Methodological Recommendations for the Course Graduate Work), Moscow: Mosk. Gos. Tekhnol. Univ., Stankin, 2007.

Download references

Author information

Authors and Affiliations

  1. Naberezhnye Chelny Institute, Kazan Federal University, Kazan, Russia

    V. V. Zvezdin, R. M. Khisamutdinov, R. R. Saubanov, I. Kh. Israfilov, S. M. Portnov & S. Yu. Yurasov

  2. Stankin Moscow State Technical University, Moscow, Russia

    V. A. Grechishnikov

Authors
  1. V. V. Zvezdin
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. R. M. Khisamutdinov
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. V. A. Grechishnikov
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. R. R. Saubanov
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. I. Kh. Israfilov
    View author publications

    You can also search for this author in PubMed Google Scholar

  6. S. M. Portnov
    View author publications

    You can also search for this author in PubMed Google Scholar

  7. S. Yu. Yurasov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to V. V. Zvezdin, R. M. Khisamutdinov, V. A. Grechishnikov, R. R. Saubanov, I. Kh. Israfilov, S. M. Portnov or S. Yu. Yurasov.

Additional information

Translated by Bernard Gilbert

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zvezdin, V.V., Khisamutdinov, R.M., Grechishnikov, V.A. et al. Laser Machining of Tool Steels. Russ. Engin. Res. 38, 1038–1041 (2018). https://doi.org/10.3103/S1068798X18120213

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X18120213

Keywords:

Search

Navigation