Skip to main content
SpringerLink
Log in

Theory of Intermittent Cutting. 3. Description of Tool Exit from the Blank

  • Published:
Russian Engineering Research Aims and scope

Abstract

Vorontsov’s plastic-flow method permits the derivation of a model of cutting for the region where the tool exits the blank. The stress–strain state of the blank is determined, and the dimensions of the plastic-deformation zone are calculated. The main cutting parameters are shown to be variable.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Vorontsov, A.L., Albagachiev, A.Yu., and Sultan-Zade, N.M., Teoreticheskie osnovy obrabotki metallov v mashinostroenii (Theoretical Basis of Metal Processing in Machine Engineering), Staryi Oskol: TNT, 2014.

    Google Scholar 

  2. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting. 1. Introduction, Russ. Eng. Res., 2008, vol. 28, no. 1, pp. 48–59.

    Google Scholar 

  3. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 2. A review of cutting theory, Russ. Eng. Res., 2008, vol. 28, no. 2, pp. 144–155.

    Google Scholar 

  4. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting. 3. Current theory of failure with plastic deformation, Russ. Eng. Res., 2008, vol. 28, no. 3, pp. 243–250.

    Google Scholar 

  5. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 4. General principles of a new theory of cutting, Russ. Eng. Res., 2008, vol. 28, no. 4, pp. 346–351.

    Article  Google Scholar 

  6. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 5. Determining the kinematic, stress, and strain states of the blank, Russ. Eng. Res., 2008, vol. 28, no. 5, pp. 461–471.

    Article  Google Scholar 

  7. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting: 6. Determining the basic parameters of cutting, Russ. Eng. Res., 2008, vol. 28, no. 6, pp. 571–578.

    Article  Google Scholar 

  8. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 7. Mathematical description of the formation of different chips, pulsation of the cutting force, and contact parameters of the machined billet surface and the rear cutter surface, Russ. Eng. Res., 2008, vol. 28, no. 7, pp. 674–680.

    Article  Google Scholar 

  9. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 8. Chip-breaker design, Russ. Eng. Res., 2008, vol. 28, no. 8, pp. 786–792.

    Article  Google Scholar 

  10. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 9. Practical calculations of cutting parameters in turning, Russ. Eng. Res., 2008, vol. 28, no. 9, pp. 878–888.

    Article  Google Scholar 

  11. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 10. Planing and broaching, Russ. Eng. Res., 2008, vol. 28, no. 10, pp. 984–986.

    Article  Google Scholar 

  12. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 11. Calculation of cylindrical-milling parameters, Russ. Eng. Res., 2008, vol. 28, no. 10, pp. 987–993.

    Article  Google Scholar 

  13. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 12. Calculation of complex-milling parameters, Russ. Eng. Res., 2008, vol. 28, no. 11, pp. 1104–1108.

    Article  Google Scholar 

  14. Vorontsov, A.L., Sultan-Zade, N.M., and Albagachiev, A.Yu., Development of a new theory of cutting 13. Calculation of end-milling parameters, Russ. Eng. Res., 2008, vol. 28, no. 12, pp. 1207–1216.

    Article  Google Scholar 

  15. Solodkov, V.A., Effect of diffusion processes on the performance of a carbide tool with intermittent cutting, Stanki Instrum., 2006, no. 6, pp. 13–15.

    Google Scholar 

  16. Loladze, T.N., Prochnost’ i iznosostoikost’ rezhushchego instrumenta (Strength and Wear Resistance of Cutting Tools), Moscow: Mashinostroenie, 1982.

    Google Scholar 

  17. Ambrosimov, S.K. and Bol’shakov, A.N., Cutter exit from machining zone in discontinuous free orthogonal cutting, Russ. Eng. Res., 2014, vol. 34, no. 9, pp. 592–595.

    Article  Google Scholar 

  18. Subich, V.N., Shestakov, N.A., Demin, V.A., et al., Raschet i proektirovanie protsessov ob”emnoi shtampovki (Calculation and Design of Bulk Forging Processes), Moscow: Mosk. Gos. Ind. Univ., 2007.

    Google Scholar 

  19. Vorontsov, A.L., Teoriya i raschety protsessov obrabotki metallov davleniem (Theory and Calculations of Metal Forming by Pressure), Moscow: Mosk. Gos. Tekh. Univ. im. N.E. Baumana, 2014, vol. 1.

    Google Scholar 

  20. Krokha, V.A., Krivye uprochneniya metallov pri kholodnoi deformatsii (Curves of Hardening of Metals during Cold Deformation), Moscow: Mashinostroenie, 1968.

    Google Scholar 

  21. Krokha, V.A., Uprochnenie metallov pri kholodnoi plasticheskoi deformatsii: Spravochnik (Strengthening of Metals in Cold Plastic Deformation: Handbook), Moscow: Mashinostroenie, 1980.

    Google Scholar 

  22. Bol’shakov, A.N., The edge effect that occurring during the tooth leaving from the treatment zone, Trenie Smazka Mash. Mekh., 2013, no. 10, pp. 41–45.

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Bunin Yelets State University, Yelets, Russia

    A. N. Bol’shakov

Authors
  1. A. N. Bol’shakov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to A. N. Bol’shakov.

Additional information

Original Russian Text © A.N. Bol’shakov, 2018, published in Vestnik Mashinostroeniya, 2018, No. 4, pp. 60–66.

For parts 1 and 2, see Steel Transl., nos. 5 and 6, 2018.

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Bol’shakov, A.N. Theory of Intermittent Cutting. 3. Description of Tool Exit from the Blank. Russ. Engin. Res. 38, 519–525 (2018). https://doi.org/10.3103/S1068798X18070043

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X18070043

Keywords

Search

Navigation