Abstract
A new method is proposed for the design of grinding operations—that is, the selection of tool characteristics and machining conditions. In this approach, tool performance is predicted, and combinations of wheel characteristics and grinding conditions are selected on that basis, with simultaneous satisfaction of all the constraints on the grinding operations and the specifications in the drawing of the part. By variant design of the grinding operations, the tool best suited to specific grinding conditions may be identified during preproduction.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
D’yakonov, A.A., Capabilities of internal-grinding wheels, Russ. Eng. Res., 2014, vol. 34, no. 12, pp. 781–784.
Dabrowski, L. and Marciniak, M., Efficiency of special segmental grinding wheel, J. Mater. Process. Technol., 2001, vol. 109, no. 3, pp. 264–269.
Kumar, S. and Choudhury, S.K., Prediction of wear and surface roughness in electro-discharge diamond grinding, J. Mater. Process. Technol., 2007, vol. 191, pp. 206–209.
Garcia, E., Meresse, D., Pombo, I., Sanches, J.-A., and Dubar, L.E., Complementary tribometers for the analysis of contact phenomena in grinding, J. Mater. Process. Technol., 2014, vol. 214, pp. 1787–1797.
Warren, L.T., Fengming, T., Qu, J., and Blau, P.J., Grinding wheel condition monitoring with boosted minimum distance classifiers, Mech. Syst. Signal Process., 2008, vol. 22, pp. 217–232.
Ardashev, D.V., Standardization of grinding wheels, Russ. Eng. Res., 2011, vol. 31, no. 9, pp. 910–912.
Dyakonov, A.A., Simulated stochastic thermo-physical model of grinding process, Proc. World Congr. on Engineering and Computer Science (WCECS 2014), October 22–24, 2014, San Francisco, Hong Kong: Newswood Academic, 2014, pp. 871–875.
Shipulin, L.V., Complex model of surface grinding, Proc. Int. Multi-Conf. of Engineers and Computer Scientists 2012 (IMECS 2012), March 14–16, 2012, Hong Kong, 2012, pp. 1325–1327.
Ardashev, D.V., Description of the operational capabilities of grinding wheels, Vestn. Yuzh.-Ural. Gos. Univ., Ser. Mashinostr., 2012, no. 33, pp. 113–116.
Ardashev, D.V., Group abrasive machining in flexible production, Russ. Eng. Res., 2015, vol. 35, no. 4, pp. 305–306.
Ardashev, D.V., Anel’chik, D.E., Butorin, G.I., et al., Rezhimy rezaniya na raboty, vypolnyaemye na shlifoval’nykh i dovorodnykh stankakh s ruchnym upravleniem i poluavtomatakh: Spravochnik (Cutting Modes for Operations Performed on Grinding and Finishing Machines with Hand and Semiautomatic Control: Handbook), Chelyabinsk: Atokso, 2007.
Korchak, S.N., Proizvoditel’nost’ protsessa shlifovaniya stal’nykh detalei (Efficiency of Grinding of the Steel Parts), Moscow: Mashinostroenie, 1974.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © D.V. Ardashev, V.I. Guzeev, 2016, published in STIN, 2016, No. 11, pp. 32–35.
About this article
Cite this article
Ardashev, D.V., Guzeev, V.I. Variative designing of grinding operations. Russ. Engin. Res. 37, 459–461 (2017). https://doi.org/10.3103/S1068798X17050045
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X17050045