Skip to main content
SpringerLink
Log in

High-quality tools in the machining of commutators

  • Published:
Russian Engineering Research Aims and scope

Abstract

The design of tools for machining the commutators of electric motors is considered. To improve machining quality and the productivity of commutator repair, the finishing operations—grinding and polishing—may be replaced by final turning with a cutter sharpened by superblade technology.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Zakharchenko, D.D. and Rotanov, N.A., Tyagovye elektricheskie mashiny: uchebnoe posobie dlya vuzov (Traction Electric Machines: Manual for Higher Education Institutions), Moscow: Transport, 1991.

    Google Scholar 

  2. Soldatkin, A.V., Improvement of commutation stability of traction electric machines by improvement of reparation technology of collectors, Extended Abstract of Cand. Sci. (Tech.) Dissertation, Omsk, 2013.

    Google Scholar 

  3. Duyun, T.A., Vibrational stability during turning of contact surface of collector of electric engine, Izv. Tul’sk. Gos. Univ., Tekh. Nauki, 2009, no. 4, pp. 43–48.

    Google Scholar 

  4. Belan, D.Yu. and Luzin, V.M., Reliability improvement of operation of collector-commutator brush assembly of traction electric engines, Izv. Transsiba, 2010, no. 4 (4), pp. 6–11.

    Google Scholar 

  5. Popov, A.Yu., Rechenko, D.S., Vasil’ev, E.V., et al., The technology of diamond grinding of carbide products, Vestn. Ufimsk. Gos. Aviats. Tekh. Univ., 2012, vol. 16, no. 4 (49), pp. 24–29.

    Google Scholar 

  6. Kosilova, A.G. and Meshcheryakov, R.K., Spravochnik tekhnologa-mashinostroitelya (Handbook of Technologist- Mechanician), Moscow: Mashinostroenie, 1985, vol. 2.

    Google Scholar 

  7. Grechishnikov, V.A., Korotkov, I.A., Skhirtladze, A.G., and Gorokhov, V.A., Proektirovanie rezhushchego instrumenta: uchebnoe posobie (Design of Cutting Tools: Manual), Moscow: Korvet, 2005.

    Google Scholar 

  8. Smennye plastiny i instrument SANDVIK-MKTS: Katalog V-100.04 rus. (Changeable Plates and Tools of SANDVIK MKTS: Catalogue V-100.04, RUS), Moscow: SANDVIK MKTS, 2000.

Download references

Author information

Authors and Affiliations

  1. Omsk State University of Railroad Transportation, Omsk, Russia

    D. Yu. Belan & V. V. Dyundin

  2. Omsk State Technical University, Omsk, Russia

    D. S. Rechenko & Yu. V. Titov

Authors
  1. D. Yu. Belan
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. V. V. Dyundin
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. D. S. Rechenko
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Yu. V. Titov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to D. Yu. Belan.

Additional information

Original Russian Text © D.Yu. Belan, V.V. Dyundin, D.S. Rechenko, Yu.V. Titov, 2016, published in STIN, 2016, No. 5, pp. 15–18.

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Belan, D.Y., Dyundin, V.V., Rechenko, D.S. et al. High-quality tools in the machining of commutators. Russ. Engin. Res. 36, 948–950 (2016). https://doi.org/10.3103/S1068798X16110058

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X16110058

Keywords

Search

Navigation