Skip to main content
SpringerLink
Log in

Improving the performance of metal-cutting tools

  • Published:
Russian Engineering Research Aims and scope

Abstract

A hard-alloy end mill capable of faster machining of curvilinear surfaces — in particular, in the production of gas-turbine blades — is proposed. Options for improving the performance of hard-alloy tools on the basis of ultrasound are discussed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Malyshev, V.I., Stanovlenie i razvitie nauki o rezanii materialov (Formation and Development of the Science of Cutting of Materials), Tolyatti: Tolyat. Gos. Univ., 2015.

    Google Scholar 

  2. Prushkov, B.T., Otechestvennaya nauka i praktika v rabotakh po issledovaniyu i sovershenstvovaniyu geometrii reztsa (National Sciences and Practice in Analysis and Improvement of the Tool Geometry), Saratov: Sarat. Knizh. Izd., 1958.

    Google Scholar 

  3. Sandvik Coromant Company. http://www.sandvik.coromant.com/en-gb/knowledge/general_turning/selection- of-inserts/geometry-information/wiper-inserts.

  4. Khramov, A.V., Leksin, E.N., and Semdyakin, I.V., RF Patent 145350, 2014.

    Google Scholar 

  5. Kirsanov, S.V., Solid carbide axial cutting tools, Inzh. Zh., 2012, no. 3, pp. 2–23.

    Google Scholar 

  6. Kumabe, J., Vibration Cutting, Tokyo: Jikkyou, 1979.

    Google Scholar 

  7. Kiselev, E.S., Efficiency improvement of the mechanical treatment by energy use of low-power module ultrasonic oscillations, Naukoemkie Tekhnol. Mekh. Obrab. Mashinostr., 2013, no. 6, pp. 3–13.

    Google Scholar 

  8. Kiselev, E.S. and Koval’nogov, V.N., Mechanical treatment of billets affected by critical heat mass transfer, in Izbrannye trudy Rossiiskoi shkoly po problemam nauki i tekhnologii (Selected Research Works of the Russian School of Science and Technologies), Moscow: Ross. Akad. Nauk, 2008.

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. HALTEC, Ulyanovsk, Russia

    A. V. Khramov, E. N. Leksin & I. V. Semdyankin

  2. Ulyanovsk State Technical University, Ulyanovsk, Russia

    E. S. Kiselev & M. V. Nazarov

Authors
  1. A. V. Khramov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. E. N. Leksin
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. I. V. Semdyankin
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. E. S. Kiselev
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. M. V. Nazarov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to E. N. Leksin.

Additional information

Original Russian Text © A.V. Khramov, E.N. Leksin, I.V. Semdyankin, E.S. Kiselev, M.V. Nazarov, 2016, published in STIN, 2016, No. 1, pp. 21–26.

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Khramov, A.V., Leksin, E.N., Semdyankin, I.V. et al. Improving the performance of metal-cutting tools. Russ. Engin. Res. 36, 684–689 (2016). https://doi.org/10.3103/S1068798X16080141

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X16080141

Keywords

Search

Navigation