Skip to main content
SpringerLink
Log in

Predicting the cutting properties of hard alloys for the manufacture of components used in gas-turbine engines

  • Published:
Russian Engineering Research Aims and scope

Abstract

Hard-alloy tools for the machining of components used in gas-turbine engines are considered. Thermodynamic analysis of the relation between tool wear and mechanical and thermal phenomena provides the basis for an express method of selecting the best tool material.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Makarov, A.D., Iznos i stoikost’ rezhushchego instrumenta (Wear and Durability of Cutting Tools), Moscow: Mashinostroenie, 1966.

    Google Scholar 

  2. Postnov, V.V., Analysis of the pattern of transient processes of metal cutting, Vestn. Ufim. Gos. Aviats. Tekhn. Univ., 2000, no. 2, pp. 203–207.

    Google Scholar 

  3. Pisarenko, G.S. and Lebedev, A.A., Deformirovanie i prochnost’ materialov pri slozhnom napryazhennom sostoyanii (Deformation and Strength of Materials Affected by Complex Stress), Kiev: Naukova Dumka, 1976.

    Google Scholar 

  4. Postnov, V.V. and Khadiullin, S.Kh., Thermodynamic criteria for evaluation of the cutting ability of the tool materials, Vestn. Ufim. Gos. Aviats. Tekhn. Univ., 2007, vol. 9, no. 6, pp. 162–169.

    Google Scholar 

  5. Postnov, V.V., Intensifikatsiya nestatsionarnogo rezaniya trudnoobrabatyvaemykh materialov na osnove termodinamicheskikh uslovii iznashivaniya rezhushchego instrumenta (Improvement of Nonstationary Cutting of Hard Materials by Optimization of Wear Conditions of Cutting Tools), Ufa: Ufim. Gos. Aviats. Tekhn. Univ., 2005.

    Google Scholar 

  6. Khadiullin, S.Kh., Efficiency improvement for use of instrumental hard alloys based on forecasting of cutting properties, Cand. Sci. (Tech.) Dissertation, Ufa: Ufim. State Aviation Tech. Univ., 2011.

    Google Scholar 

  7. Postnov,V.V., Khadiullin,S.Kh., Koev,Yu.A., and Malakhov,E.N., RF Patent 2423205.

  8. Gurevich, Ya.L., Rezhimy rezaniya trudnoobrabatyvaemykh materialov. Spravochnik (Cutting Regimes of Hard Materials: Handbook), Moscow: Mashinostroenie, 1986.

    Google Scholar 

  9. Khadiullin, S.Kh., Microstructure of worn surfaces of a hard-alloy tool, Russ. Eng. Res., 2008, vol. 28, no. 6, pp. 595–597.

    Article  Google Scholar 

  10. Khadiullin, S.Kh., Thermodynamic assessment of the operational efficiency of hard-alloy tools, Russ. Eng. Res., 2009, vol. 29, no. 12, pp. 1290–1292.

    Article  Google Scholar 

  11. Postnov, V.V., Khadiullin, S.Kh., Malakhov, E.N., and Starovoitov, S.V., Analysis of the key parameters of the cutting properties of instrumental hard alloys during treatment of hard materials, Vestn. Ufim. Gos. Aviats. Tekhn. Univ., 2012, vol. 16, no. 8 (53), pp. 118–125.

    Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Ufa State Aviation-Engineering University, Ufa, Russia

    V. V. Postnov, S. Kh. Khadiullin & S. V. Starovoitov

Authors
  1. V. V. Postnov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. S. Kh. Khadiullin
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. S. V. Starovoitov
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to V. V. Postnov.

Additional information

Original Russian Text © V.V. Postnov, S.Kh. Khadiullin, S.V. Starovoitov, 2015, published in STIN, 2015, No. 11, pp. 20–26.

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Postnov, V.V., Khadiullin, S.K. & Starovoitov, S.V. Predicting the cutting properties of hard alloys for the manufacture of components used in gas-turbine engines. Russ. Engin. Res. 36, 496–501 (2016). https://doi.org/10.3103/S1068798X16060174

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1068798X16060174

Keywords

Search

Navigation