Abstract
The influence of dressing of the abrasive tool and the table’s direction on the final surface roughness R a in deep grinding of titanium alloys by a silicon-carbide wheel is investigated. Formulas are derived by dispersional analysis of R a measurements over the length of the blank.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Starkov, V.K., Shlifovanie vysokoporistymi krugami (Grinding by Highly Porous Wheels), Moscow: Mashinostroenie, 2007.
Poletaev, V.A. and Volkov, D.I., Glubinnoe shlifovanie lopatok turbin: biblioteka tekhnologa (Deep Grinding of Turbine Blades: Technologists’ Library), Moscow: Mashinostroenie, 2006.
Poklad, V.A., Abysov, I.A., Starkov, V.K., and Ryabtsev, S.A., Surface-layer properties of turbine blade tailpiece in deep grinding by highly porous wheels, Russ. Eng. Res., 2010, vol. 30, no. 11, pp. 1132–1136.
Nosenko, V.A. and Nosenko, S.V., Unidirectional and opposing deep grinding of titanium alloy with periodic wheel adjustment, Russ. Eng. Res., 2010, vol. 30, no. 10, pp. 1016–1021.
Nosenko, V.A. and Nosenko, S.V., Deep grinding of titanium alloy with continuous wheel correction, Russ. Eng. Res., 2010, vol. 30, no. 11, pp. 1124–1128.
Nosenko, V.A., Zhukov, V.K., Zotova, S.A., and Nosenko, S.V., Removal of material at different stages of deep plane grinding, Russ. Eng. Res., 2008, vol. 28, no. 6, pp. 606–610.
Starkov, V.K., Deep grinding with continuous tool correction, Russ. Eng. Res., 2010, vol. 30, no. 12, pp. 1218–1221.
Nosenko, V.A., Avilov, A.V., and Nosenko, S.V., Variation of force in deep plane grinding, Svarochn., Inzh. Zh., 2009, no. 7, pp. 10–26.
Nosenko, V.A. and Nosenko, S.V., Mathematical models of operating time and cutting capacity for various stages of flat creep feed grinding of horizontal surface by circle of direct profile, J. Machin. Manuf. Rel., 2010, vol. 39, no. 4, pp. 380–385.
Kobzar’, A.I., Prikladnaya matematicheskaya statistika. Dlya Inzhenerov i nauchnykh rabotnikov (Applied Statistics for Engineers), Moscow: Fizmatlit, 2006.
Nosenko, V.A. and Nosenko, S.V., Deep grinding of slots in titanium-alloy blanks with continuous dressing of the grinding wheel, Vestn. Mashinostr., 2013, no. 4, pp. 74–79.
Nosenko, V.A., Vasil’ev, A.A., and Nosenko, S.V., Surface roughness for deep grinding of titanium alloy, Izv. Vyssh. Uchebn. Zaved., Mashinostr., 2007, no. 9, pp. 66–70.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © S.V. Nosenko, V.A. Nosenko, A.A. Bairamov, 2015, published in STIN, 2015, No. 1, pp. 21–26.
About this article
Cite this article
Nosenko, S.V., Nosenko, V.A. & Bairamov, A.A. Factors affecting the surface roughness in the deep grinding of titanium alloys. Russ. Engin. Res. 35, 549–553 (2015). https://doi.org/10.3103/S1068798X15070151
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X15070151