Abstract
A method is proposed for determining the parameters of the cut-layer cross section in oblique turning by a single-edge tool with a curved rear surface. The results are plotted as a function of the supply, the cutting depth, the cutter inclination, and the curvature of the rear surface.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Bobrov, V.F., Vliyanie ugla naklony glavnoi rezhushchei kromki instrumenta na protsess rezaniya metallov (Influence of the Inclination of the Tool’s Primary Cutting Edge on Metal Cutting), Moscow: Mashgiz, 1962.
Bobrov, V.F. and Ierusalimov, D.E., Rezanie metallov Samovrashchayushchimisya reztsami (Cutting Metals by Rotating Cutters), Moscow: Mashinostroenie, 1972.
Galoyan, G.P., Theoretical Principles of a New Diagonal Turning Process, with Practical Considerations, Cand. Sci. Dissertation, Leninakan, 1986.
Granovskii, G.I. and Granovskii, V.G., Rezanie metallov (Metal Cutting), Moscow: Vysshaya Shkola, 1985.
Efimov, K.V., Kratkii kurs analiticheskoi geometrii (Brief Course in Analytical Geometry), Moscow: Nauka, 1969.
Klimenko, S.A. and Manokhin, A.S., Hard turning of shaving type, Sverkhtverd. Mater., 2009, no. 1, pp. 58–74.
Konovalov, E.G., Sidorenko, V.A., and Sous’, A.V., Progressivnye skhemy rotatsionnogo rezaniya metallov (Progressive Approaches to the Rotary Cutting of Metals), Minsk: Nauka i Tekhnika, 1972.
Minasyan, G.S., Surface roughness in turning by a BRM-1 single-edge tool, Izv. Akad. Nauk ASSR, 1970, vol. 23, no. 4, pp. 3–6.
Petrushin, S.I. and Filippov, A.V., Analysis of the geometry of oblique sharpening of single-edge tools, Obrab. Met., Tekhnol., Oborud., Instrum., 2013, no. 2, pp. 8–14.
Podgorkov, V.V., Final turning by single-edge tools, Stanki Instrum., 1974, no. 1, pp. 30–31.
Ryvkin, G.M. and Samoilov, B.I., Final turning by tools with a variable cutting plate, Stanki Instrum., 1952, no. 4, pp. 20–22.
Filippov, A.V., 3D modeling of the geometry in oblique turning, Innovatsii v mashinostroenii: Sb. trudov mezhdunar, mol. konf. (Innovation in Manufacturing: Proceedings of an International Conference), Tomsk: Izd. TPU, 2012, pp. 178–182.
Filippov, A.V., Cut-layer cross section in oblique turning by a single-edge tool, Russ Eng. Res., 2014, vol. 34, no. 11, pp. 718–721.
Yashcheritsyn, P.I., Borisenko, A.V., Drivotin, I.G., and Lebedev, V.Ya., Rotatsionnoe rezanie metallov (Rotary Cutting of Metals), Minsk: Nauka i Tekhnika, 1987.
Grzesik, W., A real picture of plastic deformation concentrated in the chip produced by continuous straightedged oblique cutting, Int. J. Mach. Tools Manuf., 1991, vol. 31, no. 3, pp. 329–344.
Grzesik, W. and Zak, K., Investigations of surface texture produced by oblique machining of different workpiece materials, Arch. Mater. Sci. Eng., 2011, no. 52, pp. 46–53.
Filippov, A.V., Constructing a model of the equivalent wedge oblique cutting edge, Appl. Mechan. Mater., 2013, vol. 379, pp. 138–144.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © A.V. Filippov, 2014, published in STIN, 2014, No. 11, pp. 24–28.
About this article
Cite this article
Filippov, A.V. Cut-layer cross section in oblique turning by a single-edge tool with a curved rear surface. Russ. Engin. Res. 35, 385–388 (2015). https://doi.org/10.3103/S1068798X15050135
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X15050135