Abstract
The macrogeometry and microgeometry of a machined surface are investigated as a function of the blank’s surface quality, on the basis of a mathematical model of shaping in the course of piercing.
Similar content being viewed by others
References
Bekaev, A.A., Improving the Machined-Surface Geometry in Broaching (Piercing) by Improving the Dynamic Characteristics of the Drive, Cand. Sci. Dissertation, MAMI Moscow State Technical University, Moscow, 2006.
Shchedrin, A.V., Bekaev, A.A., Skoromnov, V.M., et al., Improving the Efficiency of Combined Drawing by Regularizing the Microgeometry of the Tool’s Working Surface, Vestn. Mashinostr., 2006, no. 11, pp. 58–60.
Shchedrin, A.V., Bekaev, A.A., Skoromnov, V.M., et al., Combined Drawing by a Tool with Regular Microrelief, Vestn. Mashinostr., 2008, no. 4, pp. 78–80.
Shchedrin, A.V., Bekaev, A.A., Ul’yanov, V.V., and Chikhacheva, N.Yu., Improving the Efficiency of Combined Hole Broaching by Regularizing the Surface Microgeometry of the Deforming Elements, Vestn. Mashinostr., 2009, no. 9, pp. 57–60.
Shchedrin, A.V., Bekaev, A.A., Skoromnov, V.M., et al., Improving the Control of Chip Formation in Machining by Deformation and Cutting, Vestn. Mashinostr., 2005, no. 12, pp. 41–42.
Shchedrin, A.V., Bekaev, A.A., Skoromnov, V.M., et al., Bauschinger Effect in Combined Machining of Metal, Vestn. Mashinostr., 2008, no. 8, pp. 71, 72.
Kochetkov, Ya.P. and Kochetkov, Yu.A., Axial Deformation of the Teeth of a Round Broach on Insertion in the Blank, Stanki Instrum., 1971, no. 4, pp. 28–30.
Kochetkov, Ya.P. and Kochetkov, Yu.A., Radial Deformation of the Teeth of a Round Broach, Stanki Instrum., 1972, no. 10, pp. 20–23.
Kochetkov, Ya.P. and Kochetkov, Yu.A., Vzaimosvyaz osevykh i radial’nykh deformatsii zub’ev krugloi protyazhki (Relation between Axial and Radial Deformation of the Teeth of a Round Broach), Available from RZh VINIT, Moscow, 1975, no. 128-75.
Krutyakova, M.V., Improving the Broaching Efficiency by Optimizing the Tool Design on the Basis of Mathematical Modeling, Cand. Sci. Dissertation, MAMI Moscow State Technical University, Moscow, 2004.
Bekaev, A.A., Mikhailov, V.A., and Kuz’minskii, D.L., Dependence of the Hole Quality and Precision after Broaching on the Corresponding Hole Parameters for the Blank, Vestn. Mashinostr., 2011, no. 4, pp. 67–69.
Baranovskii, Yu.V., Brakhman, L.A., Korchemkin, A.D., et al., Rezhimy rezaniya metallov: Spravochnik (Conditions of Metal Cutting: A Handbook), Moscow: NII-Tavtoprom, 1995.
Author information
Authors and Affiliations
Corresponding author
Additional information
Original Russian Text © Yu.V. Maksimov, A.A. Bekaev, V.A. Mikhailov, D.L. Kuz’minskii, 2011, published in Vestnik Mashinostroeniya, 2011, No. 5, pp. 17–20.
About this article
Cite this article
Maksimov, Y.V., Bekaev, A.A., Mikhailov, V.A. et al. Predicting the quality of a machined surface under an impact load at the beginning of piercing. Russ. Engin. Res. 31, 435–438 (2011). https://doi.org/10.3103/S1068798X11050145
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1068798X11050145