Skip to main content
SpringerLink
Log in

Testing Procedure for the Tribological Properties of Axial Bearings

  • EXPERIMENTAL MECHANICS, DIAGNOSTICS, AND TESTING
  • Published:
Journal of Machinery Manufacture and Reliability Aims and scope Submit manuscript

Abstract

The testing procedures of tribological properties of axial bearings are discussed. A protector with a heavy-duty axial bearing for high-speed impeller pumps has been selected as the study object. The experimental specimen is comprised of a Michell thrust block and a thrust journal. In the course of the experiments, the main operability properties have been determined.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1.
Fig. 2.
Fig. 3.
Fig. 4.
Fig. 5.
Fig. 6.

Similar content being viewed by others

REFERENCES

  1. Yushin, E.S., Nasosnoe oborudovanie sistemy truboprovodnogo transporta nefti i nefteproduktov (Pumping Equipment of the Pipeline System for Transporting Oil and Oil Products), Ukhta: Ukhtinskii Gos. Tekh. Univ., 2019.

  2. Vetokhin, V.I., New-generation submersible induction motor of open design of AMV NGS type for oil and gas wellbores, Morskoi Vestn., 2011, no. 3, p. 51.

  3. Chichinadze, A.V., Braun, E.D., Bushe, N.A., et al., Osnovy tribologii (trenie, iznos, smazka) (Foundations of Tribology: Friction, Wear, and Lubrication), Chichinadze, A.V., Ed., Moscow: Mashinostroenie, 2001.

    Google Scholar 

  4. Shikhvatov, A.M., Stability of gas-dynamic thrust bearings with spiral grooves, J. Mach. Manuf. Reliab., 2004, no. 6, pp. 24–30.

  5. Emel’yanov, I.A., Increasing the operational characteristics of thrust gasdynamic bearings, Cand. Sci. (Eng.) Dissertation, Kaluga: Bauman State Technical University (Kaluga Branch), 2001.

  6. Qiu, Y. and Khonsari, M.M., Investigation of tribological behaviors of annular rings with spiral groove, Tribol. Int., 2011, vol. 44, no. 12, pp. 1610–1619. https://doi.org/10.1016/j.triboint.2011.05.008

    Article  Google Scholar 

  7. Suh, M., Chae, Y., Kim, S., Hinoki, T., and Kohyama, A., Effect of geometrical parameters in micro-grooved crosshatch pattern under lubricated sliding friction, Tribol. Int., 2010, vol. 43, no. 8, pp. 1508–1517. https://doi.org/10.1016/j.triboint.2010.02.012

    Article  Google Scholar 

  8. Peskovatskov, M.N., Splavskii, I.S., and Voronin, N.A., Model triboanalysis of perspective materials for high-speed thrust plain bearings, Fundamental’nye issledovaniya i innovatsionnye tekhnologii v mashinostroenii, Nauchnye Trudy VII Mezhdunarodnoi nauchnoi konferentsii (Fundamental Studies and Innovation Technologies in Mechanical Engineering: Proc. 7th Int. Sci. Conf.), 2021, p. 189.

  9. Korchak, A.V., Modeling and calculation software of thrust foil bearings, Vestn. Voronezh. Gos. Tekh. Univ., 2011, vol. 7, no. 4, pp. 138–142.

  10. Sytin, A.V., Kirichek, A.A., and Tyurin, V.O., Dynamic model of thrust foil gas dynamic bearing taking into account axial impacts, Izv. Tul. Gos. Univ. Tekh. Nauki, 2021, no. 4, pp. 93–100. https://doi.org/10.24412/2071-6168-2021-4-93-100

  11. Splavskiy, I.S. and Kulakov, O.I., Ways for improving the tribotechnical properties of thrust plain bearings, XXXII Mezhdunarodnaya innovatsionnaya konferentsiya molodykh uchenykh i studentov po problemam mashinovedeniya (32nd Int. Innovation Conf. of Young Researchers and Students on Problems of Mechanical Engineering), Moscow, 2021, Moscow: Inst. Mashinovedeniya im. A.A. Blagonravova, Ross. Akad. Nauk, 2021, pp. 241–246.

  12. Prokopenko, A.A., Martsinkovskii, V.S., and Lazarenko, A.D., Providing the economic efficiency and ecological safety of turbocompressors of synthesis gas, Issledovanie, konstruirovanie i tekhnologiya izgotovleniya kompressornykh mashin. Trudy XI Mezhdunarodnoi nauchno-tekhnicheskoi konferentsii molodykh spetsialistov (Research, Design, and Technology of Manufacturing of Compressor Machines: Proc. 11th Int. Sci.-Tech. Conf. of Young Specialists), Kazan, 2022, Kazan: Vizard, 2022, pp. 123–133.

Download references

Author information

Authors and Affiliations

  1. Moscow, Russia

    E. M. Cheremisinov

  2. Mechanical Engineering Research Institute of the Russian Academy of Sciences, 101900, Moscow, Russia

    I. S. Splavskiy

Authors
  1. E. M. Cheremisinov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. I. S. Splavskiy
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to I. S. Splavskiy.

Ethics declarations

The authors declare that they have no conflicts of interest.

Additional information

Translated by I. Moshkin

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Cheremisinov, E.M., Splavskiy, I.S. Testing Procedure for the Tribological Properties of Axial Bearings. J. Mach. Manuf. Reliab. 52, 281–285 (2023). https://doi.org/10.3103/S1052618823020024

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.3103/S1052618823020024

Keywords:

Search

Navigation