Abstract
In this paper, we consider the application of optimization algorithms to solve the problem of determining the operating area of a robot with mechanisms of relative manipulation based on a plane 3-RPR mechanism and a tripod mechanism. A method for approximating the set of solutions to a system of nonlinear inequalities describing constraints on the geometric parameters of the robot is considered. Algorithms for constructing the operating areas of individual mechanisms were synthesized. The orientation effect of the output link on the size and shape of the operating area of each mechanism is analyzed. The operating area of the robot is obtained taking into account the constraints on the geometric parameters of the workpiece being in a moving coordinate system located in the center of the flat 3-RPR mechanism, as well as taking into account design constraints, intersections of links, and special positions.
Similar content being viewed by others
REFERENCES
Kong, H. and Gosselin, C.M., Type Synthesis of Parallel Mechanisms, Springer, 2007.
Merlet, J.-P., Parallel Robots, Springer, 2007, 2nd ed., p. 269.
Aleshin, A.K., Glazunov, V.A., Rashoyan, G.V., and Shai, O., Analysis of kinematic screws that determine the topology of singular zones of parallel-structure robots, J. Mach. Manuf. Reliab., 2016, vol. 45, no. 4, p. 291.
Merlet, J.P., Determination of 6D workspace of gough-type parallel manipulator and comparison between different geometries, Int. J. Rob. Res., 1999, vol. 18, no. 9, p. 902.
Evtushenko, Yu.G., A numerical method for finding the global extremum of functions (enumeration on a nonuniform grid), Zh. Vychisl. Mat. Mat. Fiz., 1971, vol. 11, no. 6, p. 1390.
Evtushenko, Y., Posypkin, M., Rybak, L., and Turkin, A., Approximating a solution set of nonlinear inequalities, J. Global Optim., 2018, vol. 7, p. 129.
Evtushenko, Y., Posypkin, M., Turkin, A., and Rybak, L., The non-uniform covering approach to manipulator workspace assessment, Proceedings of the 2017 IEEE Russia Section Young Researchers in Electrical and Electronic Engineering Conference (ElConRus 2017), 2017, p. 386.
Rybak, L.A., Posypkin, M.A., and Turkin, A.V., Method for approximating the workspace of the parallel robot, Int. J. Pharm. Technol., 2016, vol. 8, no. 4, p. 25045.
Arakelian, V., Briot, S., and Glazunov, V., Increase of singularity-free zones in the workspace of parallel manipulators using mechanisms of variable structure, Mech. Mach. Theory, 2008, vol. 43, p. 1129.
Glazunov, V.A., Shalyukhin, K.A., Levin, S.V., and Kostereva, S.D., RU Patent 2415744, 2011.
Pundru Srinivasa Rao and Nalluri Mohan Rao, Position analysis of spatial 3-RPS parallel manipulator, Int. J. Mech. Eng. Rob. Res., 2013, vol. 2, no. 2, p. 80.
Virabyan, L.G., Khalapyan, S.Yu., and Kuz’mina, V.S., Optimization of the positioning trajectory of the output link of a planar parallel robot, Vestn. Belgorod. Gos. Tekh. Univ. im. V. G. Shukhova, 2018, no. 9, p. 106.
Chablat, D. and Wenger, P., Moveability and collision analysis for fully-parallel manipulators, Proceedings of the 12th CISM-IFTOMM Symposium, Paris, 1998, p. 61.
Wenger, P. and Chablat, D., Workspace and assembly modes in fully parallel manipulators: A descriptive study, in Advances in Robot Kinematics: Analysis and Control, Dordrecht: Springer, 1998, p. 117.
Merlet, J-P., Analysis of the influence of wire interference on the workspace of wire robots, in Advances in Robot Kinematics: Analysis and Control, Sestri-Levante, 2004, pp. 211–218.
Cortes, J. and Simeon, T., Probabilistic motion planning for parallel mechanisms, Proceedings of the IEEE International Conference on Robotics and Automation, 2003, p. 4354.
Merlet, J.P. and Daney, D., Legs interference checking of parallel robots over a given workspace or trajectory, Proceedings of the IEEE International Conference on Robotics and Automation, 2006, p. 757.
Merlet, J.-P., Geometrical determination of the workspace of a constrained parallel manipulator, in Advances in Robot Kinematics: Analysis and Control, Ferrare, 1992, pp. 326–329.
Masory, O. and Wang, J., Workspace evaluation of Stewart platform, Adv. Rob., 1995, vol. 9, no. 4, p. 443.
Murali, K.K., Aravind, B., Rangaprasad, A.S., and Sandipan, B., Computation of the safe working zones of planar and spatial parallel manipulators, Robotica, 2019, vol. 38, no. 5, p. 861.
Aleshin, A.K., Glazunov, V.A., Rashoyan, G.V., and Offer Shai, Analysis of kinematic screws that determine the topology of singular zones of parallel-structure robots, J. Mach. Manuf. Reliab., 2016, vol. 45, pp. 291–296.
Gosselin, C. and Angeles, J., Singularity analysis of closed-loop kinematic chains, IEEE Trans. Rob. Autom., 1990, vol. 6, no. 3, p. 281.
Funding
This work was supported by the Russian Science Foundation, project nos. 16-19-00148 and 17-79-10512.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors declare that they have no conflict of interest.
Additional information
Translated by A. Ivanov
About this article
Cite this article
Gaponenko, E.V., Rybak, L.A. & Malyshev, D.I. Numerical Method for Determining the Operating Area of a Robot with Relative Manipulation Mechanisms. J. Mach. Manuf. Reliab. 49, 474–489 (2020). https://doi.org/10.3103/S1052618820060035
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1052618820060035