Advertisement

Automatic Control and Computer Sciences

, Volume 51, Issue 7, pp 614–620 | Cite as

Numerical Simulation of Adiabatic Shear-Band Formation in Composites

Article
  • 14 Downloads

Abstract

The process of plastic flow localization in a composite material consisting of welded steel and copper plates under shear strain is considered. The mathematical model of this physical process is formulated. A new numerical algorithm based on the Courant–Isaacson–Rees scheme is proposed. The algorithm is verified using three test problems. The algorithm efficiency and performance are proved by the test simulations. The proposed algorithm is used for numerical simulation of plastic strain localization on composite materials. The influence of boundary conditions, the initial plastic strain rate, and the width of the materials forming the composite bar on the localization process is studied. It is demonstrated that at the initial stage, the shear velocity for the material layers varies. Theoretical estimates of the oscillation frequency and period are proposed; the calculations using these estimates agree completely with the numerical experiments. It is established that the deformation is localized in the copper part of the composite. One or two localization regions situated at a typical distance from the boundaries are formed, depending on the width of the steel and copper parts, as well as the initial plastic strain rate and the chosen boundary conditions. The dependence of this distance on the initial plastic strain rate is demonstrated and corresponding estimates for boundary conditions of two types are obtained. It is established that in the case of two localization regions, the temperature and deformation in one of them increase much faster than in the other, while at the initial stage these quantities are nearly equal in both regions.

Keywords

shear band plastic flow localization plastic strain numerical simulation 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    Schneider, J. and Nunes, J.A., Characterization of plastic flow and resulting microtextures in a friction stir weld, Metall. Mater. Trans. B., 2004, vol. 35, pp. 777–783.CrossRefGoogle Scholar
  2. 2.
    Seidel, T. and Reynolds, A., Visualization of the material flow in aa2195 friction stir welds using a marker insert technique, Metall. Mater. Trans., 2001, vol. 32A, pp. 2879–2884.CrossRefGoogle Scholar
  3. 3.
    Moss, G., Shear strains, strain rates, temperature changes in adiabatic shear bands, in Waves and High Strain Rate Phenomena in Metals, Meyers, L. and MurrShock, L., Eds., Springer, 1981.Google Scholar
  4. 4.
    Rogers, H.C., Adiabatic plastic deformation, Annu. Rev. Mater. Sci., 1979, vol. 9.Google Scholar
  5. 5.
    Bai, Y. and Dodd, B., Adiabatic Shear Localization, Pergamon Press, Oxford, 1992.Google Scholar
  6. 6.
    Lee, W.S., Liu, C.Y., and Chen, T.C., Adiabatic shearing bends havior of different steels under extreme high shear loading, J. Nuclear Mater., 2008, vol. 374, pp. 313–319.CrossRefGoogle Scholar
  7. 7.
    Gupta, G., Was, G.S., and Alexandreanu, B., Grain boundary engineering of ferritiction martensitic alloy T91, Metall. Mater. Trans. A, 2004, vol. 35, pp. 717–719.CrossRefGoogle Scholar
  8. 8.
    Rittel, D., Adiabatic shear failure of a syntactic polymeric foam, Mater. Lett., 2005, vol. 59, pp. 723–732.CrossRefGoogle Scholar
  9. 9.
    Shockey, D.A., et al., Shear failure of inconel 718 under dynamic loads, Exp. Mech., 2007, vol. 47, pp. 723–732.CrossRefGoogle Scholar
  10. 10.
    Wright, T.W., The Physics and Mathematics of Adiabatic Shear Bands, Cambridge University Press, 2002.MATHGoogle Scholar
  11. 11.
    Marchand, A. and Duffy, J., An experimental study of the formation process of adiabatic shear bands in a structural steel, J. Mech. Phys. Solids, 1988, vol. 36, pp. 251–283.CrossRefGoogle Scholar
  12. 12.
    Kolsky, H., An investigation of the mechanical properties of materials at very. High rates of loading, Proc. Phys. Soc., 1949, vol. 62-B, p. 676.CrossRefGoogle Scholar
  13. 13.
    Nesterenko, V.F. and Bondar, M.P., Investigation of deformation localization by the ‘thick-walled cylinder’ method, DYMAT J., 1994, vol. 1, pp. 245–251.Google Scholar
  14. 14.
    Zhou, F., Wright, T.W., and Ramesh, K.T., A numerical methodology for investigating the formation of adiabatic shear bands, J. Mech. Phys. Solids, 2006, vol. 54, pp. 904–926.CrossRefMATHGoogle Scholar
  15. 15.
    Zhou, F., Wright, T.W., and Ramesh, K.T., The formation of multiple adiabatic shear bands, J. Mech. Phys. Solids, 2006, vol. 54, pp. 1376–1400.CrossRefMATHGoogle Scholar
  16. 16.
    Batra, R.C. and Wei, Z.G., Shear bands due to heat flux prescribed at boundaries, Int. J. Plast., 2006, vol. 22, pp. 1–15.CrossRefMATHGoogle Scholar
  17. 17.
    Kudryashov, N.A., Ryabov, P.N., and Zakharchenko, A.S., Self-organization of adiabatic shear bands in OFHC copper and HY-100 steel, J. Mech. Phys. Solids, 2015, vol. 76, pp. 180–192.MathSciNetCrossRefGoogle Scholar
  18. 18.
    Walter, J.W., Numerical experiments on adiabatic shear band formation in one dimension, Int. J. Plast., 1992, vol. 8, pp. 657–693.CrossRefGoogle Scholar
  19. 19.
    Rozhdestvenskii, B.L. and Yanenko, N.N., Sistemy kvazilineinykh uravnenii i ikh prilozheniya k gazovoi dinamike (Systems of Quasilinear Equations and Their Applications to Gas Dynamics), Moscow: Nauka, 1978.MATHGoogle Scholar
  20. 20.
    Koshkin, V.I., Kudryashov, N.A., and Ryabov, P.N., Numerical simulation of the formation of adiabatic shear bands under deformations, Yad. Fiz. Inzh., 2010, vol. 1, pp. 465–474.Google Scholar

Copyright information

© Allerton Press, Inc. 2017

Authors and Affiliations

  • N. A. Kudryashov
    • 1
  • R. V. Muratov
    • 1
  • P. N. Ryabov
    • 1
  1. 1.National Nuclear Research University MEPhI (Moscow Engineering Physics Institute)MoscowRussia

Personalised recommendations