Advertisement

Journal of Friction and Wear

, Volume 39, Issue 6, pp 528–534 | Cite as

Improving the Working Capacity Resource for a Roller Cone–Drill Rod Joint of a Drill Bit

  • D. G. Gromakovsky
  • L. V. KudyurovEmail author
  • S. V. Shigin
Article

Abstract

The results of the experimental development and studies on the structure, rigidity and damping capacity of a joint between a roller cone and a drill bit (C–D) are presented. A single-mass and a two-mass mathematical model for the C–D junction dynamics are developed. It is shown, taking into account the experimental data, that the single-mass model is significantly less accurate than the two-mass one in modeling the junction dynamics and, therefore, the two-mass model can be adopted as the basic one for performing calculations concerning the longevity of a modernized drill bit. To increase the service life of the joints, a technical solution is developed that increases the load capacity and longevity of the drill bits, based on introducing a three-layer damping package of intermediate washers into the modernized C–D junction and the use of multilubrication technology. As shown by the tests and calculations, such a modification makes it possible to reduce the deformation energy by 60% compared to the scheme adopted earlier (with one intermediate washer in the joint), which provides an increase in the service life and load capacity of the junction.

Keywords:

experimental studies mathematical model junction dynamics deformation energy longevity 

Notes

REFERENCES

  1. 1.
    Bogomolov, R.M., Borodin, V.S., Gromakovsky, D.G., and Shigin, S.V., Thrust bearing of rock roller bits with higher bearing capacity, Trenie Smazka Mash. Mekh., 2011, no. 3, pp. 31–37.Google Scholar
  2. 2.
    Kalinin, A.G., Burenie neftyanykh i gazovykh skvazhin (Drilling of Oil and Gas Wells), Moscow: TsentrLitNefteGaz, 2008.Google Scholar
  3. 3.
    Gromakovsky, D.G., Shigin, S.V., Borodin, V.S., Karpukhin, M.V., and Khaustov, V.I., Development of composite antiwear and anti-friction gaskets for bearing units, Materialy XVII Mezhdunarodnoi konferentsii “Fizika prochnosti i plastichnosti materialov,” 23–25 iyun’ 2009 g., Tezisy dokladov (Proc. XVII Int. Conf. “Physics of Durability and Plasticity of Materials,” June 23–25, 2009, Abstracts of Papers), Samara: Samar. Gos. Tekh. Univ., 2009, p. 33. ISBN 978-5-7964-1208-4Google Scholar
  4. 4.
    Gromakovsky, D.G., Ibatullin, I.D., Shigin, S.V., Balashov, E.S., and Bogomolov, R.M., RF Patent 2399743, 2010.Google Scholar
  5. 5.
    Ponomarev, Yu.K., Shigin, S.V., Nazarov, M.Kh., Chekmasov, D.A., and Datskov, A.V., The absorbing ability of lubricating layers in plate systems, Trudy Mezhdunarodnoi nauchno-tekhnicheskoi konferentsii “Aktual’nye problemy tribologii,” g. Samara, iyun’ 2007 (Proc. Int. Sci.-Tech. Conf. “Urgent Problems of Tribology,” Samara, June 2007), Samara, 2007, no. 2, pp. 306–315.Google Scholar
  6. 6.
    Burovoi porodorazrushayushchii instrument. Tom 1. Sharoshechnye dolota: Mezhdunarodnyi translyator-spravochnik (Rock Drilling Tools, Vol. 1: Roller Cone Bits: International Compiled Handbook), Kershenbaum, V.Ya., Torgasheva, A.V., and Messer, A.G., Eds., Moscow: Rinko-Al’yans, 2003.Google Scholar
  7. 7.
    Catalog of mining roller cone bits of JSC VBM-Group: User’s manual, 2009. http://www.wbmbits.com.Google Scholar
  8. 8.
    GOST (State Standard) 25 100–2011: Soils. Classification, Moscow: Standartinform, 2013.Google Scholar
  9. 9.
    Kalinin, A.G., Grigoryan, N.A., and Sultanov, B.Z., Burenie naklonnykh skvazhin (Drilling of Inclined Wells), Moscow: Nedra, 1990, pp. 203–204.Google Scholar
  10. 10.
    Bulatov, A.I. and Avetisov, A.G., Spravochnik inzhenera po bureniyu (Drilling Engineer Handbook), Moscow: Nedra, 1993, books 1–4.Google Scholar

Copyright information

© Allerton Press, Inc. 2018

Authors and Affiliations

  • D. G. Gromakovsky
    • 1
  • L. V. Kudyurov
    • 1
    Email author
  • S. V. Shigin
    • 1
  1. 1.Samara State Technical UniversitySamaraRussia

Personalised recommendations