Abstract
Mathematical models are been proposed to simulate the thermal and metallurgical behaviors of the strip occurring on the run-out table (ROT) in a hot strip mill. A variational method is utilized for the discretization of the governing transient conduction-convection equation, with heat transfer coefficients adaptively determined by the actual mill data. To consider the thermal effect of phase transformation during cooling, a constitutive equation for describing austenite decomposition kinetics of steel in air and water cooling zones is coupled with the heat transfer model. As the basic required inputs in the numerical simulations, thermal material properties are experimentally measured for three carbon steels and the least squares method is used to statistically derive regression models for the properties, including specific heat and thermal conductivity. The numerical simulation and experimental results show that the setup accuracy of the temperature prediction system of ROT is effectively improved.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Chen, S.X., Fu, X., Zou, J., 2006. Study on finishing temperature setting system and self-adaptation of hot strip mill. Iron and Steel, 41:44–48 (in Chinese).
Han, H.N., Lee, J.K., Kim, H.J., 2002. A model for deformation, temperature and phase transformation behavior of steels on ROT in hot strip mill. Journal of Materials Processing Technology, 128(1–3):216–225. [doi:10.1016/S0924-0136(02)00454-5]
Moaveni, S., 2005. Finite Element Analysis. Pearson Education, Inc., New York, p.322–323 (in Chinese).
Mukhopadhyay, A., Sikdar, S., 2005. Implementation of on-line ROT model in a hot strip mill. Journal of Materials Processing Technology, 169(2):164–172. [doi:10.1016/j.jmatprotec.2005.04.039]
Prieto, M.M., Ruiz, L.S., Menendez, J.A., 2001. Thermal performance of numerical model of hot strip mill runout table. Ironmaking and Steelmaking, 28(6):474–480. [doi:10.1179/030192301678352]
Serajzadeh, S., 2003. Prediction of temperature distribution and phase transformation on the ROT in the process of hot strip rolling. Applied Mathematical Modelling, 27(11):861–875. [doi:10.1016/S0307-904X(03)00085-4]
Serajzadeh, S., 2006. Prediction of temperature variations and kinetics of austenite phase change on the ROT. Materials Science Engineering A, 421(1–2):260–267. [doi:10.1016/j.msea.2006.01.071]
Singh, A., Singh, I.V., Prakash, R., 2006. Numerical solution of temperature dependent thermal conductivity problems using a meshless method. Numerical Heat Transfer Part A: Applications, 50(2):125–145. [doi:10.1080/10407780500507111]
Sun, C.G., Han, H.N., Lee, J.K., 2002. A finite element model for the prediction of thermal and metallurgical behavior of strip on ROT in hot rolling. ISIJ International, 42(4):392–400. [doi:10.2355/isijinternational.42.392]
Tan, X., Conway, P.P., Sarvar, F., 2005. Thermo-mechanical properties and regression models of alloys: AISI 305, CK 60, CuBe2 and Laiton MS 63. Journal of Materials Processing Technology, 168:152–163.
Zhang, Y.T., Li, D.Z., Li, Y.Y., 2006. Modeling of austenite decomposition in plain carbon steels during hot rolling. Journal of Materials Processing Technology, 171(2):175–179. [doi:10.1016/j.jmatprotec.2005.07.003]
Author information
Authors and Affiliations
Corresponding author
Additional information
Project supported by the National Basic Research Program (973) of China (No. 2006CB705400) and the National Natural Science Foundation of China (No. 50575200)
Rights and permissions
About this article
Cite this article
Chen, Sx., Zou, J. & Fu, X. Coupled models of heat transfer and phase transformation for the run-out table in hot rolling. J. Zhejiang Univ. Sci. A 9, 932–939 (2008). https://doi.org/10.1631/jzus.A0720046
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1631/jzus.A0720046