Advertisement

Journal of Zhejiang University-SCIENCE A

, Volume 19, Issue 9, pp 676–690 | Cite as

Parameters optimization of a parallel-flow heat exchanger with a new type of anti-vibration baffle and coiled wire using Taguchi method

  • Chu-lin Yu
  • Zhi-wen Ren
  • Min Zeng
  • Min-dong Ji
Article

Abstract

This study presents the thermal-hydraulic optimization of the design parameters of a parallel-flow shell-and-tube heat exchanger with a new type of anti-vibration hexagon clamping baffle and equilateral triangle cross-sectioned coiled wire. A periodic flow unit duct with non-staggered tube layout is adopted as the numerical analysis model by Fluent. The Taguchi method is used to explore the influence of five geometric parameters including baffle distance (A), baffle width (B), coil diameter (C), coil pitch (D), and the side length of the equilateral triangle (E). An L18 (35) orthogonal array is chosen to carry out the numerical simulation. The comprehensive thermal-hydraulic performance evaluation criterion (PEC) is set as the optimization goal. The results show that the order of the factor effectiveness for the Nusselt number is E>C>A>D>B, for the flow friction is C>E>A>B>D and for the PEC is C>E>A>B>D. This means that the coil pitch has a great influence while the baffle width and the coil diameter have a trifling effect. Finally, the optimal factor combination for PEC is obtained. The PEC of the optimal combination is 0.19%–1.92% higher than the model with better comprehensive performance among 18 cases for Reynolds number in the range from 14 465 to 32 547.

Key words

Optimization Parallel-flow Anti-vibration Hexagon clamping baffle Coiled wire Taguchi method 

基于田口方法的带新型防振折流板和线圈的平行流换热器参数优化

摘要

目 的

圆形折流杆管壳式换热器容易发生流体诱发振动, 从而引起管束失效。 本文旨在探索壳程采用正三角形截面的线圈和六边形防振折流板的平行流换热器的传热特性和传热强化机理。

创新点

  1. 1.

    提出一种具有防振功能的带六边形折流板和正三角形截面螺旋线圈的平行流管壳式换热器;

     
  2. 2.

    采用田口方法揭示几何参数对传热和流动性能的影响;

     
  3. 3.

    以提高换热器的综合性能为目标函数, 得出最优的几何参数组合。

     

方 法

  1. 1.

    采用数值模拟方法和田口方法, 分析带六边形防振折流板和正三角形截面线圈的平行流换热器几何参数对传热流动特性的影响;

     
  2. 2.

    综合对比分析速度、 压力、 温度和湍流场分布的影响, 揭示传热强化机理。

     

结 论

  1. 1.

    得到了不同几何参数对传热和流动的影响程度; 其中, 线圈的节距对传热和流动的影响程度最大, 而六边形夹持防振折流板厚度的影响最小。

     
  2. 2.

    采用田口方法优化后的结构较原结构的综合 性能提高0.19%~1.92%。

     

关键词

优化 平行流 六边形夹持 抗振折流板 圆形线圈 田口方法 

CLC number

TK124 

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. Bas H, Ozceyhan V, 2014. Optimization of parameters for heat transfer and pressure drop in a tube with twisted tape inserts by using Taguchi method. Arabian Journal for Science and Engineering, 39(2):1177–1186.  https://doi.org/10.1007/s13369-013-0648-4 CrossRefGoogle Scholar
  2. Bovand M, Rashidi S, Esfahani JA, 2015. Enhancement of heat transfer by nanofluids and orientations of the equilateral triangular obstacle. Energy Conversion and Management, 97:212–223.  https://doi.org/10.1016/j.enconman.2015.03.042 CrossRefGoogle Scholar
  3. Chen YP, Sheng YJ, Dong C, et al., 2013. Numerical simulation on flow field in circumferential overlap trisection helical baffle heat exchanger. Applied Thermal Engineering, 50(1):1035–1043.  https://doi.org/10.1016/j.applthermaleng.2012.07.031 CrossRefGoogle Scholar
  4. Deng XH, Deng SJ, 1998. Investigation of heat transfer enhancement of roughened tube bundles supported by ring or rod supports. Heat Transfer Engineering, 19(2):21–27.  https://doi.org/10.1080/01457639808939917 CrossRefGoogle Scholar
  5. Dong QW, Wang YQ, Liu MS, 2008. Numerical and experimental investigation of shellside characteristics for RODbaffle heat exchanger. Applied Thermal Engineering, 28(7):651–660.  https://doi.org/10.1016/j.applthermaleng.2007.06.038 CrossRefGoogle Scholar
  6. El Maakoul A, Laknizi A, Saadeddine S, et al., 2016. Numerical comparison of shell–side performance for shell and tube heat exchangers with trefoil–hole, helical and segmental baffles. Applied Thermal Engineering, 109: 175–185.  https://doi.org/10.1016/j.applthermaleng.2016.08.067 Google Scholar
  7. Gentry CC, 1990. Rodbaffle heat exchanger technology. Chemical Engineering Progress, 86(7):48–57.Google Scholar
  8. Gunes S, Manay E, Senyigit E, et al., 2011. A Taguchi approach for optimization of design parameters in a tube with coiled wire inserts. Applied Thermal Engineering, 31(14–15):2568–2577.  https://doi.org/10.1016/j.applthermaleng.2011.04.022 CrossRefGoogle Scholar
  9. Huang YQ, Yu XL, Lu GD, 2008. Numerical simulation and optimization design of the EGR cooler in vehicle. Journal of Zhejiang University–SCIENCE A, 9(9):1270–1276.  https://doi.org/10.1631/jzus.A0820223 CrossRefzbMATHGoogle Scholar
  10. Hutagalung FF, 2014. Vibration vulnerability of rod baffle type heat exchanger: case study badak LNG MCR aftercooler. Proceedings of ASME International Mechanical Engineering Congress and Exposition, 13:V013T16A005.  https://doi.org/10.1115/imece2014-39673 Google Scholar
  11. Keklikcioglu O, Ozceyhan V, 2016. Experimental investigation on heat transfer enhancement of a tube with coiled–wire inserts installed with a separation from the tube wall. International Communications in Heat and Mass Transfer, 78:88–94.  https://doi.org/10.1016/j.icheatmasstransfer.2016.08.024 CrossRefGoogle Scholar
  12. Keklikcioglu O, Ozceyhan V, 2017. Entropy generation analysis for a circular tube with equilateral triangle cross sectioned coiled–wire inserts. Energy, 139:65–75.  https://doi.org/10.1016/j.energy.2017.07.145 CrossRefGoogle Scholar
  13. Li J, Liu MS, Dong QW, 2005. Numerical investigation of an innovative vibration–proof baffle element for a heat exchanger with longitudinal flows at the shell side. Journal of Engineering for Thermal Energy and Power, 20(6): 579–583 (in Chinese).  https://doi.org/10.3969/j.issn.1001-2060.2005.06.006 Google Scholar
  14. Liu JC, Zhang SY, Zhao XY, et al., 2015. Influence of fin arrangement on fluid flow and heat transfer in the inlet of a plate–fin heat exchanger. Journal of Zhejiang University–SCIENCE A (Applied Physics & Engineering), 16(4):279–294.  https://doi.org/10.1631/jzus.A1400270 CrossRefGoogle Scholar
  15. Master BI, Chunangad KS, Pushpanathan V, 2003. Fouling mitigation using helixchanger heat exchangers. Proceedings of the ECI Conference on Heat Exchanger Fouling and Cleaning: Fundamentals and Applications, 1:317–322.Google Scholar
  16. Promvonge P, 2008. Thermal performance in circular tube fitted with coiled square wires. Energy Conversion and Management, 49(5):980–987.  https://doi.org/10.1016/j.enconman.2007.10.005 CrossRefGoogle Scholar
  17. Sheng YJ, Chen YP, Cao RB, et al., 2012. Experimental study on shell–side heat transfer and flow resistance performance of heat exchangers with non–round orifice baffles. Journal of Southeast University (Natural Science Edition), 42(2):318–322.  https://doi.org/10.3969/j.issn.1001-0505.2012.02.024 Google Scholar
  18. Wang H, Liu YW, Yang P, et al., 2016. Parametric study and optimization of H–type finned tube heat exchangers using Taguchi method. Applied Thermal Engineering, 103:128–138.  https://doi.org/10.1016/j.applthermaleng.2016.03.033 CrossRefGoogle Scholar
  19. Wang LK, Sundén B, 2002. Performance comparison of some tube inserts. International Communications in Heat and Mass Transfer, 29(1):45–56.  https://doi.org/10.1016/s0735-1933(01)00323-2 CrossRefGoogle Scholar
  20. Wang QW, Chen QY, Chen GD, et al., 2009. Numerical investigation on combined multiple shell–pass shell–andtube heat exchanger with continuous helical baffles. International Journal of Heat and Mass Transfer, 52(5–6): 1214–1222.  https://doi.org/10.1016/j.ijheatmasstransfer.2008.09.009 CrossRefzbMATHGoogle Scholar
  21. Wang YQ, Dong QW, Liu MS, 2007. Characteristics of fluid flow and heat transfer in shellside of heat exchangers with longitudinal flow of shellside fluid with different supporting structures. International Conference on Power Engineering, p.474–479.  https://doi.org/10.1007/978-3-540-76694-0_87 Google Scholar
  22. Wang YS, Liu ZC, Huang SY, 2011. Experimental investigation of shell–and–tube heat exchanger with a new type of baffles. Heat and Mass Transfer, 47(7):833–839.  https://doi.org/10.1007/s00231-010-0590-x CrossRefGoogle Scholar
  23. Yan LW, Wu JX, Wang ZW, 2004. Industrially experimental investigations and development of the curve–ROD baffle heat exchanger. Journal of Shanghai University (English Edition), 8(3):337–341.  https://doi.org/10.1007/s11741-004-0075-6 CrossRefGoogle Scholar
  24. Yang J, Liu W, 2015. Numerical investigation on a novel shell–and–tube heat exchanger with plate baffles and experimental validation. Energy Conversion and Management, 101:689–696.  https://doi.org/10.1016/j.enconman.2015.05.066 CrossRefGoogle Scholar
  25. You YH, Chen YQ, Xie MQ, et al., 2015. Numerical simulation and performance improvement for a small size shell–and–tube heat exchanger with trefoil–hole baffles. Applied Thermal Engineering, 89:220–228.  https://doi.org/10.1016/j.applthermaleng.2015.06.012 CrossRefGoogle Scholar
  26. Yun JY, Lee KS, 2000. Influence of design parameters on the heat transfer and flow friction characteristics of the heat exchanger with slit fins. International Journal of Heat and Mass Transfer, 43(14):2529–2539.  https://doi.org/10.1016/s0017-9310(99)00342-7 CrossRefzbMATHGoogle Scholar
  27. Zeng M, Tang LH, Lin M, et al., 2010. Optimization of heat exchangers with vortex–generator fin by Taguchi method. Applied Thermal Engineering, 30(13):1775–1783.  https://doi.org/10.1016/j.applthermaleng.2010.04.009 CrossRefGoogle Scholar
  28. Zhang JF, He YL, Tao WQ, 2009. 3D numerical simulation on shell–and–tube heat exchangers with middle–overlapped helical baffles and continuous baffles–part I: numerical model and results of whole heat exchanger with middleoverlapped helical baffles. International Journal of Heat and Mass Transfer, 52(23–24):5371–5380.  https://doi.org/10.1016/j.ijheatmasstransfer.2009.07.006 CrossRefzbMATHGoogle Scholar
  29. Zhang JF, Guo SL, Li ZZ, et al., 2013. Experimental performance comparison of shell–and–tube oil coolers with overlapped helical baffles and segmental baffles. Applied Thermal Engineering, 58(1–2):336–343.  https://doi.org/10.1016/j.applthermaleng.2013.04.009 MathSciNetCrossRefGoogle Scholar

Copyright information

© Zhejiang University and Springer-Verlag GmbH Germany, part of Springer Nature 2018

Authors and Affiliations

  1. 1.Clean Combustion and Flue Gas Purification Key Laboratory of Sichuan ProvinceDongfang Boiler Group Co., Ltd.ChengduChina
  2. 2.MOE Key Laboratory of Thermo-Fluid Science and EngineeringXi’an Jiaotong UniversityXi’anChina

Personalised recommendations