Abstract
Research has shown that the post-peak tensile strength behaviour of Steel Fibre-Reinforced Concrete (SFRC) elements is significantly affected by the distribution of fibres in the section. The pursuit towards the effective and optimal application of SFRC in practice necessitates a thorough understanding of the influence of fibre spatial distribution on composite performance. In this research, the influence of fibre length and volume content on the spatial distribution of fibres was investigated using a photometric image analysis technique. A unique approach was developed that utilises Voronoi diagrams as the geometric descriptor quantifying fibre spatial distribution. The resulting parameters characterised the sectional dispersion of fibres as well as the degree of clustering and were related to the flexural performance of notched beams tested under three-point loading. The findings of the study highlight the role of fibre length and volume content on the spatial distribution of fibres and it is revealed that the sectional uniformity, inter-batch spatial variability, and degree of clustering are dependent on the number of fibres in the cross section. Furthermore, the results demonstrated the considerable influence of fibre distribution on the flexural performance of SFRC. It was concluded that the variability in flexural strength reduced as the variation in fibre spatial distribution reduced and that extensive clustering had an adverse effect on the effective resistance provided by fibres.
Similar content being viewed by others
References
Laranjeira F, Grünewald S, Walraven J, Blom C, Molins C, Aguado A (2011) Characterization of the orientation profile of steel fiber reinforced concrete. Mater Struct 44(6):1093–1111
Parmentier B, Vandewalle L, Van Rickstal F (2008) Evaluation of the scatter of the postpeak behaviour of fibre reinforced concrete in bending: a step towards reliability. In: Gettu R (ed) BEFIB 2008: 7th RILEM international symposium on fibre reinforced concrete, 2008. RILEM Publications SARL, pp 133–143
Di Prisco M, Plizzari G, Vandewalle L (2009) Fibre reinforced concrete: new design perspectives. Mater Struct 42(9):1261–1281
Ferrara L, Ozyurt N, Di Prisco M (2011) High mechanical performance of fibre reinforced cementitious composites: the role of “casting-flow induced” fibre orientation. Mater Struct 44(1):109–128
Zhou B, Uchida Y (2017) Relationship between fiber orientation/distribution and post-cracking behaviour in ultra-high-performance fiber-reinforced concrete (UHPFRC). Cem Concr Compos 83:66–75
Segura-Castillo L, Cavalaro SHP, Goodier C, Aguado A, Austin S (2018) Fibre distribution and tensile response anisotropy in sprayed fibre reinforced concrete. Mater Struct 51(1):29
Yoo D-Y, Kang S-T, Yoon Y-S (2014) Effect of fiber length and placement method on flexural behavior, tension-softening curve, and fiber distribution characteristics of UHPFRC. Constr Build Mater 64:67–81
RILEM TC 162-TDF (2002) Recommendations of RILEM TC 162-TDF: test and design methods for steel fibre reinforced concrete: bending test. Mater Struct 35(9):579–582
Barr B, Lee M, de Place Hansen EJ, Dupont D, Erdem E, Schaerlaekens S, Schnütgen B, Stang H, Vandewalle L (2003) Round-robin analysis of the RILEM TC 162-TDF beam-bending test: part 1—test method evaluation. Mater Struct 36(9):609–620
Barr B, Lee M, de Place Hansen EJ, Dupont D, Erdem E, Schaerlaekens S, Schnütgen B, Stang H, Vandewalle L (2003) Round-robin analysis of the RILEM TC 162-TDF beam-bending test: part 3—fibre distribution. Mater Struct 36(9):631–635
Li VC (1992) A simplified micromechanical model of compressive strength of fiber-reinforced cementitious composites. Cem Concr Compos 14(2):131–141
Naaman AE, Shah SP (1976) Pull-out mechanism in steel fiber-reinforced concrete. ASCE J Struct Div 102(8):1537–1548
Rusch T, Hornik K, Mair P (2018) Assessing and quantifying clusteredness: the OPTICS Cordillera. J Comput Graph Stat 27(1):220–233
Akkaya Y, Peled A, Shah S (2000) Parameters related to fiber length and processing in cementitious composites. Mater Struct 33(8):515–524
Akkaya Y, Shah SP, Ankenman B (2001) Effect of fiber dispersion on multiple cracking of cement composites. J Eng Mech 127(4):311–316
Ozyurt N, Woo LY, Mason TO, Shah SP (2006) Monitoring fiber dispersion in fiber-reinforced cementitious materials: comparison of AC-impedance spectroscopy and image analysis. ACI Mater J 103(5):340
Žirgulis G, Švec O, Sarmiento EV, Geiker MR, Cwirzen A, Kanstad T (2016) Importance of quantification of steel fibre orientation for residual flexural tensile strength in FRC. Mater Struct 49(9):3861–3877
Lee BY, Kang S-T, Yun H-B, Kim YY (2016) Improved sectional image analysis technique for evaluating fiber orientations in fiber-reinforced cement-based materials. Mater 9(1):42
Andries J, Van Itterbeeck P, Vandewalle L, Van Geysel A (2015) Influence of concrete flow on spatial distribution and orientation of fibres in steel fibre reinforced self-compacting concrete. In: fib symposium, Copenhagen, Denmark
Bernasconi A, Cosmi F, Hine P (2012) Analysis of fibre orientation distribution in short fibre reinforced polymers: a comparison between optical and tomographic methods. Compos Sci Technol 72(16):2002–2008
Liu J, Li C, Liu J, Cui G, Yang Z (2013) Study on 3D spatial distribution of steel fibers in fiber reinforced cementitious composites through micro-CT technique. Constr Build Mater 48:656–661
Ponikiewski T, Katzer J (2016) X-ray computed tomography of fibre reinforced self-compacting concrete as a tool of assessing its flexural behaviour. Mater Struct 49(6):2131–2140
Ozyurt N, Mason TO, Shah SP (2007) Correlation of fiber dispersion, rheology and mechanical performance of FRCs. Cem Concr Compos 29(2):70–79
Otsu N (1979) A threshold selection method from gray-level histograms. IEEE Trans Syst Man Cybern 9(1):62–66
Vincent L, Soille P (1991) Watersheds in digital spaces: an efficient algorithm based on immersion simulations. IEEE Trans Pattern Anal Mach Intell 6:583–598
De Berg M (2008) Computational geometry: algorithms and applications, 3rd edn. Springer, Berlin
Jasiūnienė E, Cicėnas V, Grigaliūnas P, Rudžionis Ž, Navickas AA (2018) Influence of the rheological properties on the steel fibre distribution and orientation in self-compacting concrete. Mater Struct 51(4):103
Blanco A, Cavalaro S, De la Fuente A, Grünewald S, Blom C, Walraven J (2015) Application of FRC constitutive models to modelling of slabs. Mater Struct 48(9):2943–2959
Yoo D-Y, Zi G, Kang S-T, Yoon Y-S (2015) Biaxial flexural behavior of ultra-high-performance fiber-reinforced concrete with different fiber lengths and placement methods. Cem Concr Compos 63:51–66
Nakagami M (1960) The m-distribution—a general formula of intensity distribution of rapid fading. In: Hoffman WG (ed) Statistical methods in radio wave propagation. Permagon Press, Oxford, pp 3–36
Barros JA, Cunha VM, Ribeiro AF, Antunes J (2005) Post-cracking behaviour of steel fibre reinforced concrete. Mater Struct 38(1):47–56
Nayar SK, Gettu R, Krishnan S (2014) Characterisation of the toughness of fibre reinforced concrete–revisited in the Indian context. Indian Concr J 88(2):8–23
Alberti M, Enfedaque A, Gálvez J (2017) On the prediction of the orientation factor and fibre distribution of steel and macro-synthetic fibres for fibre-reinforced concrete. Cem Concr Compos 77:29–48
Dupont D, Vandewalle L (2005) Distribution of steel fibres in rectangular sections. Cem Concr Compos 27(3):391–398
Kooiman AG (2000) Modelling steel fibre reinforced concrete for structural design. PhD, Delft University of Technology, Delft, Netherlands
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Below is the link to the electronic supplementary material.
Rights and permissions
About this article
Cite this article
Bosman, T., Kearsley, E.P. The influence of fibre spatial characteristics on the flexural performance of SFRC. Mater Struct 52, 51 (2019). https://doi.org/10.1617/s11527-019-1351-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1617/s11527-019-1351-z