Skip to main content
Log in

Mix design and fresh properties for high-performance printing concrete

Materials and Structures Aims and scope Submit manuscript

Abstract

This paper presents the experimental results concerning the mix design and fresh properties of a high-performance fibre-reinforced fine-aggregate concrete for printing concrete. This concrete has been designed to be extruded through a nozzle to build layer-by-layer structural components. The printing process is a novel digitally controlled additive manufacturing method which can build architectural and structural components without formwork, unlike conventional concrete construction methods. The most critical fresh properties are shown to be extrudability and buildability, which have mutual relationships with workability and open time. These properties are significantly influenced by the mix proportions and the presence of superplasticiser, retarder, accelerator and polypropylene fibres. An optimum mix is identified and validated by the full-scale manufacture of a bench component.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16

Similar content being viewed by others

References

  1. Okamura H, Ouchi M (2003) Self-compacting concrete. J Adv Concr Technol 1:5–15

    Article  Google Scholar 

  2. RILEM Technical Committee (2006) Final report of RILEM TC 188-CSC ‘Casting of self compacting concrete’. Mater Struct 39:937–954

    Article  Google Scholar 

  3. Austin SA, Robins P, Goodier CI (1999) The rheological performance of wet-process sprayed mortars. Mag Concr Res 51:341–352

    Article  Google Scholar 

  4. Austin SA, Robins P, Goodier CI (2002) Construction and repair with wet-process sprayed concrete and mortar. Technical Report 56. The Concrete Society UK

  5. Buswell R, Soar RC, Gibb A, Thorpe T (2007) Freeform construction: mega-scale rapid manufacturing for construction. Autom Constr 16:224–231

    Article  Google Scholar 

  6. Lim S, Le T, Webster J, Buswell R, Austin S, Gibb A, Thorpe T (2009) Fabricating construction components using layer manufacturing technology. Proc Int Conf Glob Innov Constr, Loughborough, pp 512–520

    Google Scholar 

  7. Austin S, Robins P, Goodier CI (2005) Low-volume wet-process sprayed concrete: pumping and spraying. Mater Struct 38:229–237

    Google Scholar 

  8. Jacobsen S (2009) Flow conditions of fresh mortar and concrete in different pipes. Cem Concr Res 39:997–1006

    Article  Google Scholar 

  9. Mu B et al (1999) Cementitious composite manufactured by extrusion technique. Cem Concr Res 29:237–240

    Article  Google Scholar 

  10. Shao Y et al (2011) Microstructure of extruded cement-bonded fibreboard. Cem Concr Res 31:1153–1161

    Article  Google Scholar 

  11. Lombois-Burger H et al (2006) Kneading and extrusion of dense polymer–cement pastes. Cem Concr Res 36:2086–2097

    Article  Google Scholar 

  12. Tattersall GH, Banfill PFG (1983) The rheology of fresh concrete. Pitman Books Ltd., London

    Google Scholar 

  13. British Standards Institution (1990) BS 1377-9:1990 methods of test for soils for civil engineering purposes. Milton Keynes

  14. Previte RW (1977) Concrete slump loss. ACI Mater J 74:361–367

    Google Scholar 

  15. Ravina D et al (1994) Slump loss and compressive strength of concrete made with WRR and HRWR admixtures and subjected to prolonged mixing. Cem Concr Res 24:1455–1462

    Article  Google Scholar 

  16. Kim BG, Jiang SP, Aitcin PC (2000) Slump improvement mechanism of alkalies in PNS superplasticized cement pastes. Mater Struct 33:363–369

    Article  Google Scholar 

  17. Alhozaimy MA (2009) Effect of absorption of limestone aggregates on strength and slump loss of concrete. Cem Concr Compos 31:470–473

    Article  Google Scholar 

  18. Le T, Soutsos MN, Millard SG, Barnett SJ (2007) UHPFRC—optimisation of mix proportions. Proc Concr Platf Int Conf, Belfast, pp 339–348

    Google Scholar 

  19. Tarmac Limited (2007) CEMROK 40A—product information

  20. British Standards Institution (2009) BS EN 12390-3:2009 testing hardened concrete. Milton Keynes

Download references

Acknowledgments

This project is funded by Engineering and Physical Sciences Research Council of the UK (EPSRC) Grant (EP/E002323/1) through the IMCRC at Loughborough University. The authors gratefully acknowledge the supply of materials from Weber (St Gobain), Hanson Cement, BASF and Grace Construction Products and the assistance in designing the freeform components from Foster + Partners and Buro Happold. The authors are also grateful for the laboratory assistance of John Webster, Jonathan Hales and David Spendlove.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to T. T. Le.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Le, T.T., Austin, S.A., Lim, S. et al. Mix design and fresh properties for high-performance printing concrete. Mater Struct 45, 1221–1232 (2012). https://doi.org/10.1617/s11527-012-9828-z

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1617/s11527-012-9828-z

Keywords

Navigation