Abstract
The photothermal experiments on the incident light angle dependence are carried out using simulated solar light on thin films of both iron oxides (Fe3O4 and Fe3O4@Cu2-xS) and porphyrin compounds (chlorophyll and chlorophyllin). Fe3O4 and Fe3O4@Cu2-xS are synthesized using various solution methods that produce mono-dispersed nanoparticles on the order of 10 nm. Chlorophyll is extracted from fresh spinach and chlorophyllin sodium copper is a commercial product. These photothermal (PT) materials are dispersed in polymethyl methacrylate (PMMA) solutions and deposited on glass substrates via spin coating that result in clear and transparent thin films. The iron-oxide based thin films show distinctive absorption spectra; Fe3O4 exhibits a strong peak near UV and gradually decreases into the visible and NIR regions; the absorption of Fe3O4@Cu2-xS is similar in the UV region but shows a broad absorption in the NIR region. Both chlorophyll and chlorophyllin are characterized with absorption peaks near UV and NIR showing a “U”-shaped spectrum, ideally required for efficient solar harvest and high transparency in energy-efficient single-pane window applications. Upon coating of the transparent PT films on the window inner surfaces, solar irradiation induces the photothermal effect, consequently raising the film temperature. In this fashion, the thermal loss through the window can be significantly lowered by reducing the temperature difference between the window inner surface and the room interior, based on a new concept of so-called optical thermal insulation (OTI) without any intervention medium, such as air/argon, as required in the glazing technologies. Single-panes are therefore possible to replace double- or triple panes. As OTI is inevitably affected by seasonal and daily sunlight changes, an incident light angle dependence of the photothermal effect is crucial in both thin film and window designs. It is found that the heating curves reach their maxima at small angles of incidence while the photothermal effect is considerably reduced at large angles. This angle dependence is well explained by light reflection by the thin film surface, however, deviated from what is predicted by the Fresnel's law, attributable to non-ideal surfaces of the substrates. The angle dependence data provide an important reference for OTI that window exposure to the sun is greater at winter solstice while that is considerably reduced in the summer. This conclusion indicates much enhanced solar harvesting and heat conversion via optically insulated windows in the winter season, resulting in much lower U-factors.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.References
EIA: Consumption & Efficiency. U.S. Energy Information Administration (2015). https://www.eia.gov/consumption/ (accessed March 10, 2020).
A.A.F. Husain, W.Z.W. Hasan, S. Shafie, M.N. Hamidon, and S.S. Pandey: A review of transparent solar photovoltaic technologies. Renew. Sust. Energy Rev. 94, 779–791 (2018).
S.Y. Chang, P. Cheng, G. Li, and Y. Yang: Transparent polymer photovoltaics for solar energy harvesting and beyond. Joule 2, 1039–1054 (2018).
D. Shi, M.E. Sadat, A.W. Dunn, and D.B. Mast: Photo-fluorescent and magnetic properties of iron oxide nanoparticles for biomedical applications. Nanoscale 7, 8209–8232 (2015).
I. Sartori, A. Napolitano, and K. Voss: Net zero energy buildings: a consistent definition framework. Energy Build. 48, 220–232 (2012).
L. Wang, J. Gwilliam, and P. Jones: Case study of zero energy house design in UK. Energy Build 41, 1215–1222 (2009).
S. Attia, E. Gratia, A. De Herde, and J.L.M. Hensen: Simulation-based decision support tool for early stages of zero-energy building design. Energy Build 49, 2–15 (2012).
Y. Zhao, M.E. Sadat, A. Dunn, H. Xu, C.H. Chen, W. Nakasuga, R.C. Ewing, and D. Shi: Photothermal effect on Fe3O4 nanoparticles irradiated by white-light for energy-efficient window applications. Sol. Energy Mater. Sol. Cells 161, 247–254 (2017).
Y. Zhao, A.W. Dunn, and D. Shi: Effective reduction of building heat loss without insulation materials via the photothermal effect of a chlorophyll thin film coated Green Window. MRS Commun. 9, 675–681 (2019).
J. Lin, Y. Zhao, and D. Shi: Optical thermal insulation via the photothermal effects of Fe3O4 and Fe3O4@Cu2-xS thin films for energy-efficient single-pane windows. MRS Commun. 10, 155–163 (2020).
J. Wang and D. Shi: Spectral selective and photothermal nano structured thin films for energy efficient windows. Appl. Energy 208, 83–96 (2017).
J.S. Choi, B.G. Choi, J.H. Kim, S.T. Ryu, C.T. Rim, and Y.S. Kim: New curved reflectors for significantly enhanced solar power generation in four seasons. Energies 12, 4602 (2019).
National Fenestration Rating Council: Procedure for Determining Fenestration Product U-factors (2013). https://www.nfrccommunity.org/store/ViewProduct.aspx?id=1380591 (accessed March 10, 2020).
E. Energy Star: ENERGY STAR Program Requirements for Residential Windows, Doors, and Skylights. https://www.energystar.gov/sites/default/files/Windows_Doors_and_Skylights_Program_Requirements%20v6.pdf (accessed March 12, 2020).
Y. Zhao, J. Lin, D.M. Kundrat, M. Bonmarin, J. Krupczak Jr., S.V. Thomas, M. Lyu, and D. Shi: Photonically-activated molecular excitations for thermal energy conversion in porphyrinic compounds. J. Phys. Chem. C 124, 1575–1584 (2020).
Solar Energy: http://www.inforse.org/europe/dieret/Solar/solar.html (accessed March 13, 2020).
Working with Solar Fabircs: https://ecofabrix.com/fabric-guide/ (accessed March 07, 2020).
Y.M. Chen, C.H. Lee, and H.C. Wu: Calculation of the optimum installation angle for fixed solar-cell panels based on the genetic algorithm and the simulated-annealing method. IEEE Trans. Energy Convers 20, 467–473 (2005).
M. Born, E. Wolf, A.B. Bhatia, P.C. Clemmow, D. Gabor, A.R. Stokes, A.M. Tayler, P.A. Wayman, and W.L. Wilcock: Principles of Optics. 7th ed. (Cambridge University Press, England, 1999).
The Carbon Neutral Design Project, Society of Building Science Educators, American Institute of Architects: Carbon Neutral Design Strategies (2012). http://www.tboake.com/carbon-aia/strategies1a.html (accessed March 11, 2020).
Solar Geometry: http://mypages.iit.edu/~maslanka/SolarGeo.pdf (accessed March 13).
W.B. Stine and M. Geyer: Power from the Sun (eBook, 2001). http://www.powerfromthesun.net/book.html (accessed March 11, 2020).
A. El-Sebaii and A.E.M. Khallaf: Mathematical modeling and experimental validation for square pyramid solar still. Environ. Sci. Pollut. Res. Published online 11 Jan 2020. doi:10.1007/s11356-019-07587-5
M. Khan: Solar still distillate productivity enhancement by using reflector and design optimization experimental investigation of nucleate pool boiling heat transfer enhancement of TiO2-water based nanofluids view project. Innov. Ener. Res. 8, 222 (2019).
M.J. Yun, Y.H. Sim, S.I. Cha, S.H. Seo, and D.Y. Lee: 3-Dimensional dye sensitized solar cell sub-module with oblique angled cell array for enhanced power and energy density output utilizing non-linear relation in cosine law of light incident angle. Sol. Energy 177, 355–363 (2019).
Y.Q. Liu, D. Wei, H.L. Cui, and D.Q. Wang: Photovoltaic effect related to methylammonium cation orientation and carrier transport properties in high-performance perovskite solar cells. ACS Appl. Mater. Interfaces 12, 3563–3571 (2020).
J.X. Liu, Q. Tian, J. Hu, Y. Zhu, R. Zou, and Z. Chen: Sub-10 nm Fe3O4@ Cu2-xS core-shell nanoparticles for dual-modal imaging and photothermal therapy. J. Am. Chem. Soc. 135, 8571–8577 (2013).
S. Upadhyay, K. Parekh, and B. Pandey: Influence of crystallite size on the magnetic properties of Fe3O4 nanoparticles. J. Alloys Compd. 678, 478–485 (2016).
S. Ali, S.A. Khan, J. Eastoe, S.R. Hussaini, M.A. Morsy, and Z.H. Yamani: Synthesis, characterization, and relaxometry studies of hydrophilic and hydrophobic superparamagnetic Fe3O4 nanoparticles for oil reservoir applications. Colloids Surfaces A Physicochem. Eng. Asp 543, 133–143 (2018).
K. Nee Koo, A. Fauzi Ismail, M. Hafiz Dzarfan Othman, M.A. Rahman, and T. Zhong Sheng: Preparation and characterization of superparamagnetic magnetite (Fe3O4) nanoparticles: a short review. Malays. J. Fundam. Appl. Sci. 15, 23–31 (2019).
A. Nagaraja, Y.M. Puttaiahgowda, A. Kulal, A.M. Parambil, and T. Varadavenkatesan: Synthesis, characterization, and fabrication of hydrophilic antimicrobial polymer thin film coatings. Macromol. Res. 27, 301–309 (2019).
W.R. Wu, C.J. Su, W.T. Chuang, Y.C. Huang, P.W. Yang, P.C. Lin, C.Y. Chen, T.Y. Yang, A.C. Su, K.H. Wei, C.M. Liu, and U.S. Jeng: Surface layering and supersaturation for top-down nanostructural development during spin coating of polymer/fullerene thin films. Adv. Energy Mater. 7, 1601842 (2017).
S. Wang, X. Zhao, Y. Tong, Q. Tang, and Y. Liu: Directly spin coating a low-viscosity organic semiconductor solution onto hydrophobic surfaces: toward high-performance solution-processable organic transistors. Adv. Mater. Interfaces 7, 1901950 (2020).
M.V. Kelso, N.K. Mahenderkar, Q. Chen, J.Z. Tubbesing, and J.A. Switzer: Spin coating epitaxial films. Science 364, 166–169 (2019).
H. Inoue, H. Yamashita, K. Furuya, Y. Nonomura, N. Yoshioka, and S. Lib: Determination of copper(II) chlorophyllin by reversed-phase high-performance liquid chromatography. J. Chromatogr. A 679, 99–104 (1994).
E. Yuliarita and A. Zulys: Utilization of natural compounds (chlorophyll and carotene extracts) as an octane-boosting additive in gasoline. IOP Conf. Ser. Mater. Sci. Eng. 496, 012048 (2019).
B. Zhang, Y. Shan, and K. Chen: A facile approach to fabricate of photothermal functional Fe3O4@CuS microspheres. Mater. Chem. Phys. 193, 82–88 (2017).
J. Singh: Optical Properties of Condensed Matter and Applications (Wiley, Chichester, UK, 2006).
R.C. Rai: Analysis of the Urbach tails in absorption spectra of undoped ZnO thin films. J. Appl. Phys. 113, 153508 (2013).
C. Boxall, G. Kelsall, and Z. Zhang: Photoelectrophoresis of colloidal iron oxides: Part 2. - Magnetite (Fe3O4). J. Chem. Soc. - Faraday Trans. 92, 791–802 (1996).
W.F.J. Fontijn, P.J. van der Zaag, L.F. Feiner, R. Metselaar, and M.A.C. Devillers: A consistent interpretation of the magneto-optical spectra of spinel type ferrites. J. Appl. Phys. 85, 5100–5105 (1999).
K.R. Nemade, and S.A. Waghuley: Band gap engineering of CuS nanoparticles for artificial photosynthesis. Mater. Sci. Semicond. Process 39, 781–785 (2015).
D. Miyazaki: Fresnel Equations (2014). https://link.springer.com/content/pdf/10.1007%2F978-0-387-31439-6_569.pdf (accessed March 11).
E. Hecht: Optics. 3rd ed. (Addison-Wesley Longman, Inc., Boston, MA, 1998).
A.A. Maradudin and E.R. Méndez: Light scattering from randomly rough surfaces. Sci. Prog. 90, 161–221 (2007).
D. Nolan, W. Senaratne, D. Baker, and L. Liu: Optical Scattering from Nanostructured Glass Surfaces. Int. J. Appl. Glas. Sci. 6, 345–355 (2015).
D.G. Stavenga: Thin film and multilayer optics cause structural colors of many insects and birds. Mater. Today: Proc. 1, 109–121 (2014).
G.A. Atkinson and E.R. Hancock: Shape estimation using polarization and shading from two views. In IEEE Transactions on Pattern Analysis and Machine Intelligence (IEEE, 29, Piscataway, New Jersey, US, 2007), pp. 2001–2017.
Acknowledgments
This research is supported by National Science Foundation CMMI-1635089. We would like to thank Dr. Andrew J. Steckl for the Perkin-Elmer spectrophotometer.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Lyu, M., Lin, J., Krupczak, J. et al. Light angle dependence of photothermal properties in oxide and porphyrin thin films for energy-efficient window applications. MRS Communications 10, 439–448 (2020). https://doi.org/10.1557/mrc.2020.39
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/mrc.2020.39