Skip to main content
SpringerLink
Log in

Kinetic study of the intermetallic compound formation between eutectic Sn−3.5Ag alloys and electroplated Ni metallization in flip-chip solder joints

  • Article
  • Published:
Journal of Materials Research Aims and scope Submit manuscript

Abstract

Ni-based under-bump metallization (UBM) has attracted wide attention due to its low reaction rate with Sn, compared with Cu and Cu alloy. In this study, the interfacial reactions between eutectic Sn–3.5Ag solder and Ni-based UBM, including electroplated Ni (EP-Ni) and electroless Ni (EL-Ni) are investigated. Morphology and growth kinetics of Ni3Sn4 intermetallic compounds are studied at different reflow temperatures and durations. The growth rate and the growth activation energy of Ni3Sn4 were measured for the two sets of samples. The activation energies are measured to be 25 kJ/mol and 38 kJ/mol for the Ni3Sn4 growth on EP-Ni and EL-Ni, respectively. The Ni3Sn4 on EP-Ni UBMs shows a slower growth rate and the Ni3Sn4/solder interface is void free even after 20-min reflow at 240 °C. On the other hand, the interface of Ni3Sn4/EL-Ni has a lot of microvoids after reflowing at 240 °C for 20 min.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

FIG. 1
FIG. 2
FIG. 3
FIG. 4
TABLE I.
FIG. 5
FIG. 6
FIG. 7
FIG. 8
FIG. 9
FIG. 10

Similar content being viewed by others

References

  1. K.N. Tu, A.M. Gusak, and M. Li: Physics and materials challenges for lead-free solders. J. Appl. Phys. 93, 1335 (2003).

    Article  CAS  Google Scholar 

  2. D. Suraski and K. Seelig: The current status of lead-free solder alloys. IEEE Trans. Electron. Packag. Manuf. 24 (4), 244 (2001).

    Article  CAS  Google Scholar 

  3. K. Zeng and K.N. Tu: Six cases of reliability study of Pb-free solder joints in electronic packaging technology. Mater. Sci. Eng., R 38, 55 (2002).

    Article  Google Scholar 

  4. S.K. Kang and V. Ramachandran: Growth kinetics of intermetallic phases at the liquid Sn and solid Ni interface. Scr. Mater. 14, 421 (1980).

    CAS  Google Scholar 

  5. M.O. Alam, Y.C. Chan, and K.C. Hung: Interfacial reaction of Pb–Sn solder and Sn–Ag solder with electroless Ni deposit during reflow. J. Electron. Mater. 31, 1117 (2002).

    Article  CAS  Google Scholar 

  6. J.W. Yoon, S.W. Kim, and S.B. Jung: Effect of reflow time on interfacial reaction and shear strength of Sn–0.7Cu solder/Cu and electroless Ni–P BGA joints. J. Alloy. Comp. 385, 192 (2004).

    Article  CAS  Google Scholar 

  7. K.N. Tu and K. Zeng: Tin–lead (SnPb) solder reaction in flip chip technology. Mater. Sci. Eng., R 34 (1), 1 (2001).

    Article  Google Scholar 

  8. H.K. Kim and K.N. Tu: Rate of consumption of Cu in soldering accompanied by ripening. Appl. Phys. Lett. 67, 2002 (1995).

    Article  CAS  Google Scholar 

  9. A.A. Liu, K.N. Kim, and P.A. Totta: Spalling of Cu6Sn5 spheroids in the soldering reaction of eutectic SnPb on Cr/Cu/Au thin films. J. Appl. Phys. 80, 2774 (1996).

    Article  CAS  Google Scholar 

  10. H.K. Kim, K.N. Tu, and P.A. Totta: Ripening-assisted asymmetric spalling of Cu–Sn compound spheroids in solder joints on Si wafers. Appl. Phys. Lett. 68 (16), 2204 (1996).

    Article  CAS  Google Scholar 

  11. R.J.K. Wassink: Soldering in Electronics, 2nd ed. (Electrochemical Publications, United Kingdom, 1984).

    Google Scholar 

  12. P.G. Kim, J.W. Jang, T.Y. Lee, and K.N. Tu: Interfacial reaction and wetting behavior in eutectic SnPb solder on Ni/Ti thin films and Ni foils. J. Appl. Phys. 86, 6746 (1999).

    Article  CAS  Google Scholar 

  13. K.L. Lin and Y.C. Liu: Reflow and property of Al/Cu/electroless nickel/Sn–Pb solder bumps. IEEE Trans. Adv. Packag. 22 (4), 568 (1992).

    Google Scholar 

  14. J.W. Yoon and S.B. Jung: Growth kinetics of Ni3Sn4 and (NiP)-P-3 layer between Sn–3.5Ag solder and electroless Ni–P substrate. J. Alloy. Comp. 376, 105 (2004).

    Article  CAS  Google Scholar 

  15. C.Y. Lee and K.L. Lin: The interaction kinetics and compound formation between electroless Ni–P and solder. Thin Solid Films 249 (2), 201 (1994).

    Article  CAS  Google Scholar 

  16. J.W. Jang, P.G. Kim, and K.N. Tu: Solder reaction-assisted crystallization of electroless Ni–P under bump metallization in low cost flip chip technology. J. Appl. Phys. 85 (12), 8456 (1999).

    Article  CAS  Google Scholar 

  17. K.C. Hung, Y.C. Chen, C.W. Tang, and H.C. Ong: Correlation between Ni3Sn4 intermetallics and Ni3P due to solder reaction-assisted crystallization of electroless Ni–P metallization in advanced packages. J. Mater. Res. 15 (11), 2534 (2000).

    Article  CAS  Google Scholar 

  18. K.C. Hung and Y.C. Chen: Study of Ni3P growth due to solder reaction-assisted crystallization of electroless Ni–P metallization. J. Mater. Sci. Lett. 19, 1755 (2000).

    Article  CAS  Google Scholar 

  19. P.L. Liu and J.K. Shang: A comparative fatigue study of solder/electroless-nickel and solder/copper interfaces. J. Mater. Res. 15 (11), 2347 (2000).

    Article  CAS  Google Scholar 

  20. S.P. Peng, C. Andersson, and X.C. Wei: High temperature aging study of intermetallic compound formation of Sn–3.5Ag and Sn–4.0Ag–0.5Cu solders on electroless Ni(P) metallization. J. Alloy. Comp. 452, 191 (2006).

    Google Scholar 

  21. S.P. Peng, W.H. Wu, C.E. Ho, and Y.M. Huang: Comparative study between Sn37Pb and Sn3Ag0.5Cu soldering with Au/Pd/Ni(P) tri-layer structure. J. Alloy. Comp. 493, 431 (2009).

    Article  CAS  Google Scholar 

  22. J.W. Jang, D.R. Peter, T.Y. Lee, and K.N. Tu: Morphology of interfacial reaction between lead-free solders and electroless Ni–P under bump metallization. J. Appl. Phys. 88, 6359 (2000).

    Article  CAS  Google Scholar 

  23. M. He, W.H. Lau, G. Qi, and Z. Chen: Intermetallic compound formation between Sn–3.5Ag solder and Ni-based metallization during liquid state reaction. Thin Solid Films 462–, 376 (2004).

    Article  CAS  Google Scholar 

  24. Y.C. Lin, T.Y. Shih, S.K. Tien, and J.G. Duh: Suppressing Ni–Sn–P growth in SnAgCu/Ni–P solder joints. Scr. Mater. 56, 49 (2007).

    Article  CAS  Google Scholar 

  25. A. Sharif, Y.C. Chan, M.N. Islam, and M.J. Rizvi: Dissolution of electroless Ni metallization by lead-free solder alloys. J. Alloy. Comp. 388, 75 (2005).

    Article  CAS  Google Scholar 

  26. M. He, A. Kumar, P.T. Yeo, G.J. Qi, and Z. Chen: Interfacial reaction between Sn-rich solders and Ni-based metallization. Thin Solid Films 462–, 387 (2004).

    Article  CAS  Google Scholar 

  27. G. Ghosh: Coarsening kinetics of Ni3Sn4 scallops during interfacial reaction between liquid eutectic solders and Cu/Ni/Pd metallization. J. Appl. Phys. 88, 6887 (2000).

    Article  CAS  Google Scholar 

  28. P.L. Tu, Y.C. Chan, K.C. Hung, and J.K.L. Lai: Effect of cooling rate on the isothermal fatigue behavior of CBGA solder joints in shear. Scr. Mater. 44, 317 (2001).

    Article  CAS  Google Scholar 

  29. G. Ghosh: Dissolution and interfacial reactions of thin-film Ti/Ni/Ag metallizations in solder joints. Acta Mater. 49, 2609 (2001).

    Article  CAS  Google Scholar 

  30. J.F. Li, S.H. Mannan, M.P. Clode, K. Chen, D.C. Whalley, C. Liu, and D.A. Hutt: Comparison of interfacial reactions of Ni and Ni–P in extended contact with liquid Sn–Bi-based solders. Acta Mater. 55, 737 (2007).

    Article  CAS  Google Scholar 

  31. G. Ghosh: Interfacial microstructure and the kinetics of interfacial reaction in diffusion couples between Sn–Pb solder and Cu/Ni/Pd metallization. Acta Mater. 48, 3719 (2000).

    Article  CAS  Google Scholar 

  32. J. Shen, Y.C. Chan, and S.Y. Liu: Growth mechanism of Ni3Sn4 in a Sn/Ni liquid/solid interfacial reaction. Acta Mater. 57, 5196 (2009).

    Article  CAS  Google Scholar 

  33. Y.C. Lin, K.J. Wang, and J.G. Duh: Detailed phase evolution of phosphorous-rich layer and formation of Ni–Sn–P compound in SnAgCu/electroplated Ni–P solder joint. J. Electron. Mater. 39, 283 (2010).

    Article  CAS  Google Scholar 

  34. Y. Takaku, X.J. Liu, I. Ohnuma, R. Kainuma, and K. Ishida: Interfacial reaction and morphology between molten Sn base solders and Cu substrate. Mater. Trans. 45, 646 (2004).

    Article  CAS  Google Scholar 

  35. R.H. Dauskardt, F. Haubensak, and R.O. Ritchie: On the interpretation of the fractal character of fracture surfaces. Acta Mater. 38 (2), 143 (1990).

    Article  CAS  Google Scholar 

  36. H.K. Kim and K.N. Tu: Kinetic analysis of the soldering reaction between eutectic SnPb alloy and Cu accompanied by ripening. Phys. Rev. B 53, 16027 (1996).

    Article  CAS  Google Scholar 

  37. S.K. Kang, R.S. Rai, and S. Purushothaman: Interfacial reactions during soldering with lead–tin eutectic and lead (Pb)–free, tin-rich solders. J. Electron. Mater. 25, 1113 (1996).

    Article  CAS  Google Scholar 

  38. D. Gur and M. Bamberger: Reactive isothermal solidification in the Ni–Sn system. Acta Mater. 46, 4917 (1998).

    Article  CAS  Google Scholar 

  39. Y.D. Jeon, K.W. Paik, K.S. Bok, W.S. Choi, and C.L. Cho: Studies of electroless nickel under bump metallurgy—Solder interfacial reactions and their effects on flip chip solder joint reliability. J. Electron. Mater. 31, 520 (2002).

    Article  CAS  Google Scholar 

  40. C.M. Chen and S.W. Chen: Electromigration effect upon the Sn–0.7 wt% Cu/Ni and Sn–3.5 wt% Ag/Ni interfacial reactions. J. Appl. Phys. 90 (3), 1208 (2001).

    Article  CAS  Google Scholar 

  41. C.E. Ho, S.C. Yang, and C.R. Kao: Interfacial reaction issues for lead-free electronic solders. J. Mater. Sci. Mater. Electron. 18, 155 (2007).

    Article  CAS  Google Scholar 

Download references

ACKNOWLEDGMENTS

The authors thank the National Science Council of Republic of China for the financial support through Grant No. 98-2221-E-009-MY3.

Author information

Authors and Affiliations

  1. Department of Materials Science and Engineering, National Chiao Tung University, Hsinchu, 30010, Taiwan, Republic of China

    Hsiao-Yun Chen & Chih Chen

Authors
  1. Hsiao-Yun Chen
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Chih Chen
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Chih Chen.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Chen, HY., Chen, C. Kinetic study of the intermetallic compound formation between eutectic Sn−3.5Ag alloys and electroplated Ni metallization in flip-chip solder joints. Journal of Materials Research 27, 1169–1177 (2012). https://doi.org/10.1557/jmr.2012.22

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1557/jmr.2012.22

Search

Navigation