Abstract
The crystallization behavior of melt-spun ribbons and bulk samples of the Cu36Zr48Al8Ag8 glassy alloy on heating is presented here. The crystallization kinetics and structural changes in the Cu36Zr48Al8Ag8 glassy alloy were studied using x-ray diffraction, transmission electron microscopy, differential scanning, and isothermal calorimetry methods. A clear comparison is made of the differences in the crystallization kinetics of the melt-spun ribbons and the copper-mold-cast bulk rod samples. It was suggested that the kinetics of crystallization in the rod sample, at any given temperature, are somewhat different than in the ribbon samples, probably because of size and free volume effects. Differences in the crystallization behavior of this alloy with other Cu-Zr-Al-Ag alloys have also been discussed.
Similar content being viewed by others
References
A. Inoue: High strength bulk amorphous alloys with low critical cooling rates. Mater. Trans., JIM36, 866 (1995).
W.L. Johnson: Bulk glass-forming metallic alloys: Science and technology. MRS Bull. 24 (10), 42 (1999).
A. Inoue: Stabilization of metallic supercooled liquid and bulk amorphous alloys. Acta Mater. 48, 279 (2000).
D.H. Xu, G. Duan, and W.L. Johnson: Unusual glass-forming ability of bulk amorphous alloys based on ordinary metal copper. Phys. Rev. Lett. 92, 245504 (2004).
D. Turnbull and M.H. Cohen: Free-volume model of the amorphous phase: Glass transition. J. Chem. Phys. 34, 120 (1961).
Z.P. Lu and C.T. Liu: A new glass-forming ability criterion for bulk metallic glasses. Acta Mater. 50, 3501 (2002).
D.V. Louzguine-Luzgin and A. Inoue: Nano-devitrification of glassy alloys. J. Nanosci. Nanotechnol. 5, 999 (2005).
A. Inoue and W. Zhang: Formation, thermal stability and mechanical properties of Cu-Zr and Cu-Hf binary glassy alloy rods. Mater. Trans. 45, 584 (2004).
D. Xu, B. Lohwongwatana, G. Duan, W.L. Johnson, and C. Garland: Bulk metallic glass formation in binary Cu-rich alloy series–Cu100−’xZrx (x=34, 36, 38.2, 40 at.%) and mechanical properties of bulk Cu64Zr36 glass. Acta Mater. 52, 2621 (2004).
D. Wang, Y. Li, B.B. Sun, M.L. Sui, K. Lu, and E. Ma: Bulk metallic glass formation in the binary Cu–Zr system. Appl. Phys. Lett. 84, 4029 (2004).
A. Inoue, W. Zhang, and J. Saida: Synthesis and fundamental properties of Cu-Based bulk glassy alloys in binary and multi-component systems. Mater. Trans. 45, 1153 (2004).
A. Inoue, W. Zhang, T. Tsurui, A.R. Yavari, and A.L. Greer: Unusual room-temperature compressive plasticity in nanocrystal-toughened bulk copper-zirconium glass. Philos. Mag. Lett. 85, 221 (2005).
A. Inoue, W. Zhang, T. Zhang, and K. Kurosaka: High-strength Cu-based bulk glassy alloys in Cu–Zr–Ti and Cu–Hf–Ti ternary systems. Acta Mater. 49, 2645 (2001).
A. Inoue and W. Zhang: Formation, thermal stability and mechanical properties of Cu-Zr-Al bulk glassy alloys. Mater. Trans. 43, 2921 (2002).
W. Zhang and A. Inoue: Formation and mechanical strength of new Cu-based bulk glassy alloys with large supercooled liquid region. Mater. Trans. 45, 1210 (2004).
A. Inoue, T. Negishi, H.M. Kimura, T. Zhang, and A.R. Yavari: High packing density of Zr- and Pd-based bulk amorphous alloys. Mater. Trans., JIM 39, 318 (1998).
R. Busch, E. Bakke, and W.L. Johnson: Viscosity of the supercooled liquid and relaxation at the glass transition of the Zr46.75Ti8.25Cu7.5Ni10Be27.5 bulk metallic glass forming alloy. Acta Mater. 46, 4725 (1998).
A.L. Greer: Metallic glasses. Science 267, 1947 (1995).
Q. Zhang, W. Zhang, and A. Inoue: Preparation of Cu36Zr48Ag8Al8 bulk metallic glass with a diameter of 25 mm by copper mold casting. Mater. Trans. 48, 629 (2007).
Z. Altounian, T. Guo-hua, and J.O. Strom-Olsen: Crystallization characteristics of Cu-Zr metallic glasses from Cu70Zr30 to Cu25Zr75. J. Appl. Phys. 53, 4755 (1982).
N. Mattern, A. Schops, U. Kuhn, J. Acker, O. Khvostikova, and J. Eckert: Structural behavior of CuxZr100-x metallic glass (x = 35–70). J. Non-Cryst. Solids 354, 1054 (2008).
D. Nagahama, T. Ohkubo, T. Mukai, and K. Hono: Characterization of nanocrystal dispersed Cu60Zr30Ti10 metallic glass. Mater. Trans. 46, 1264 (2005).
J.Z. Jiang, J. Saida, H. Kato, T. Ohsuna, and A. Inoue: Is Cu60Ti10Zr30 a bulk glass-forming alloy? Appl. Phys. Lett. 82, 4041 (2003).
D.V. Louzguine and A. Inoue: Nanocrystallization of Cu-(Zr or Hf)-Ti metallic glasses. J. Mater. Res. 17, 2112 (2002).
D.V. Louzguine and A. Inoue: Evaluation of the thermal stability of a Cu60Hf25Ti15 metallic glass. Appl. Phys. Lett. 81, 2561 (2002).
M. Kasai, J. Saida, M. Matsushita, T. Osuna, E. Matsubara, and A. Inoue: Structure and crystallization of rapidly quenched Cu-(Zr or Hf)-Ti alloys containing nanocrystalline particles. J. Phys.: Condens. Matter 14, 13867 (2002).
J.Z. Jiang, B. Yang, K. Saksl, H. Franz, and N. Pryds: Crystallization of Cu60Ti20Zr20 metallic glass with and without pressure. J. Mater. Res. 18, 895 (2003).
G.J. Fan, L.F. Fu, D.C. Qiao, H. Choo, P.K. Liaw, N.D. Browning, and J.F. Loffler: Effect of microalloying on the glass-forming ability of Cu60Zr30Ti10 bulk metallic glass. J. Non-Cryst. Solids 353, 4218 (2007).
D.V. Louzguine and A. Inoue: Influence of Ni and Co additions on supercooled liquid region, devitrification behaviour and mechanical properties of Cu-Zr-Ti bulk metallic glass. J. Metastable & Nanocrystalline Mater. 15–16, 31 (2003).
Y. Yokoyama, H. Inoue, K. Fukaura, and A. Inoue: Relationship between the liquidus surface and structures of Zr-Cu-Al bulk amorphous alloys. Mater. Trans. 43, 575 (2002).
D. Ma, H. Tan, D. Wang, Y. Li, and E. Ma: Strategy for pinpointing the best glass-forming alloys. Appl. Phys. Lett. 86, 191906 (2005).
J. Das, M.B. Tang, K.B. Kim, R. Theissmann, F. Baier, W.H. Wang, and J. Eckert: “Work-Hardenable” ductile bulk metallic glass. Phys. Rev. Lett. 94, 205501 (2005).
J. Das, S. Pauly, C. Duhamel, B.C. Wei, and J. Eckert: Microstructure and mechanical properties of slowly cooled Cu47.5Zr47.5Al5. J. Mater. Res. 22, 326 (2007).
S. Pauly, J. Das, C. Duhamel, and J. Eckert: Martensite formation in a ductile Cu47.5Zr47.5Al5 bulk metallic glass composite. Adv. Eng. Mater. 9, 487 (2007).
W. Zhang and A. Inoue: High glass-forming ability and good mechanical properties of new bulk glassy alloys in Cu-Zr-Ag ternary system. J. Mater. Res. 21, 234 (2006).
G. Duan, K. De Blauwe, M.L. Lind, J.P. Schramm, and W.L. Johnson: Compositional dependence of thermal, elastic, and mechanical properties in Cu–Zr–Ag bulk metallic glasses. Scr. Mater. 58, 159 (2008).
F. Jia, W. Zhang, and A. Inoue: Effects of additional Hf on the thermal stability and mechanical properties of Cu-Zr-Ag bulk glassy alloys. Mater. Trans. 47, 1922 (2006).
C-L. Dai, H. Guo, Y. Shen, Y. Li, E. Ma, and J. Xu: A new centimeter-diameter Cu-based bulk metallic glass. Scr. Mater. 54, 1403 (2006).
D.V. Louzguine and A. Inoue: Nanoparticles with icosahedral symmetry in Cu-based bulk glass former induced by Pd addition. Scr. Mater. 48, 1325 (2003).
D.V. Louzguine and A. Inoue: Gold as an alloying element promoting formation of a nanoicosahedral phase in a Cu-based alloy. J. Alloys Compd. 361, 153 (2003).
F.X. Qin, H.F. Zhang, B.Z. Ding, and Z.Q. Hu: Nanocrystallization kinetics of Ni-based bulk amorphous alloy. Intermetallics 12, 1197 (2004).
G. Xie, Q. Zhang, D.V. Louzguine, W. Zhang, and A. Inoue: Stability of nanocrystallites dispersed in Cu50Zr45Ti5 metallic glass under electron irradiation. J. Nanosci. Nanotechnol. 7, 3286 (2007).
Powder Diffraction Data Database, Vol. 43 (The International Center for Diffraction Database, 2003), p. 1142.
G. Xie, Q. Zhang, D.V. Louzguine-Luzgin, W. Zhang, and A. Inoue: Nanocrystallization of Cu50Zr45Ti5 metallic glass induced by electron irradiation. Mater. Trans. 47, 1930 (2006).
N. Tian, M. Ohnuma, T. Ohkubo, and K. Hono: Primary crystallization of an Al88Gd6Er2Ni4 metallic glass. Mater. Trans. 46, 2880 (2005).
K.F. Kelton and F. Spaepen: A study of the devitrification of Pd82Si18 over a wide temperature range. Acta Metall. 33, 455 (1985).
Z. Li, H. Shen, and Y. He: Surface crystallization of metallic glass Fe71Ni3Cr4Si8B14. Phys. Status Solidi A 141, 135 (2006).
D.G. Papageorgiou and G.A. Evangelakis: Adlayer deposition induced surface crystallization of Cu46Zr54 bulk metallic glass. Surf. Sci. 602, 1486 (2008).
A. Grabia, D. Oleszak, M. Kopcewicz, and J. Latuch: Crystallization behaviour of the Fe60Co10Ni10Zr7B13 metallic glass. Mater. Sci. Eng. 449–451, 552 (2007).
K.F. Kelton: Time-dependent nucleation in partitioning transformations. Acta Mater. 48, 1967 (2000).
A. Inoue and T. Zhang: Fabrication of bulk glassy Zr55Al10-Ni5Cu30 alloy of 30 mm in diameter by a suction casting method. Mater. Trans., JIM37, 185 (1996).
Á. Révész, A. Concustell, L.K. Varga, S. Suriñach, and M.D. Baro: Influence of the wheel speed on the thermal behaviour of Cu60Zr20Ti20 alloys. Mater. Sci. Eng., A375–377, 776 (2004).
J.H. Perepezko, R.J. Hebert, and G. Wilde: Synthesis of nano-structures from amorphous and crystalline phases. Mater. Sci. Eng., A375–377, 171 (2004).
G.P. Dinda, H. Rosner, and G. Wilde: Cold-rolling induced amor-phization in Cu-Zr, Cu-Ti-Zr and Cu-Ti-Zr-Ni multilayers. J. Non-Cryst. Solids 353, 3777 (2007).
E. Illekova, M. Jergel, P. Duhaj, and A. Inoue: The relation between the bulk and ribbon Zr55Ni25Al20 metallic glasses. Mater. Sci. Eng., A 226–228, 388 (1997).
D.V. Louzguine-Luzgin, T. Saito, J. Saida, and A. Inoue: Influence of cooling rate on the structure and properties of a Cu–Zr–Ti–Ag glassy alloy. J. Mater. Res. 23, 515 (2008).
D.V. Louzguine-Luzgin, G. Xie, W. Zhang, and A. Inoue: Influence of Al and Ag on the devitrification behavior of a Cu-Zr glassy alloy. Mater. Trans. 48, 2128 (2007).
L. Xia, W.H. Li, S.S. Fang, B.C. Wei, and Y.D. Dong: Binary Ni-Nb bulk metallic glasses. J. Appl. Phys. 99, 026103 (2006).
H. Tan, Y. Zhang, D. Ma, Y.P. Feng, and Y. Li: Optimum glass formation at off-eutectic composition and its relation to skewed eutectic coupled zone in the La based La-Al-(Cu, Ni) pseudo ternary system. Acta Mater. 51, 4551 (2003).
L. Xia, D. Ding, S.T. Shan, and Y.D. Dong: The glass forming ability of Cu-rich Cu–Hf binary alloys. J. Phys.: Condens. Matter 18, 3543 (2006).
W.H. Wang: Roles of minor additions in formation and properties of bulk metallic glasses. Prog. Mater. Sci. 52, 540 (2007).
D.V. Louzguine-Luzgin, A.D. Setyawan, H. Kato, and A. Inoue: Thermal conductivity of an alloy in relation to the observed cooling rate and glass-forming ability. Philos. Mag. 87, 1845 (2007).
D.V. Louzguine-Luzgin, G. Xie, W. Zhang, and A. Inoue: Devitrification behavior and glass-forming ability of Cu-Zr-Ag alloys. Mater. Sci. Eng., A465, 146 (2007).
J.C. Oh, T. Ohkubo, Y.C. Kim, E. Fleury, and K. Hono: Phase separation in Cu43Zr43Al7Ag7 bulk metallic glass. Scr. Mater. 53, 165 (2005).
S.O. Park, J.C. Lee, P.R. Cha, E. Fleury, J.P. Ahn, and Y.C. Kim: The effect of crystallization behavior on the plasticity of Cu43Zr43Al7Ag7 bulk metallic glass. J. Korean Phys. Soc. 49, 624 (2006).
A.A. Kundig, M. Ohnuma, T. Ohkubo, T. Abe, and K. Hono: Glass formation and phase separation in the Ag-Cu-Zr system. Scr. Mater. 55, 449 (2006).
I. Martin, T. Ohkubo, M. Ohnuma, and K. Hono: Nanocrystalli-zation of Zr41.2Ti13.8Cu12.5Ni10.0Be22.5 metallic glass. Acta Mater. 52, 4427 (2006).
Y. Waseda, H.S. Chen, K.T. Jacob, and H. Shibata: On the glass forming ability of liquid alloys. Sci. Technol. Adv. Mater. 9, 023003 (2008).
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Louzguine-Luzgin, D.V., Xie, G., Li, S. et al. Glass-forming ability and differences in the crystallization behavior of ribbons and rods of Cu36Zr48Al8Ag8 bulk glass-forming alloy. Journal of Materials Research 24, 1886–1895 (2009). https://doi.org/10.1557/jmr.2009.0219
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/jmr.2009.0219