References
P.R. Strutt, B.G. Lewis, and B.H. Rear, in Rapidly Solidified Amorphous and Crystalline Alloys, edited by B.H. Kear, B.C. Gleason, and M. Cohen (Elsevier Science Publishing Co., 1982) p. 485–495.
B. Mordike and H. Bergmann, in Rapidly Solidified Metastable Materials, edited by B.H. Kear and B.C. Giessen (Mater. Res. Soc. Symp. Proc. 28, Elsevier Science Publishing Co., 1984) p. 45–64.
J.C. Borland, Br. Welding J. (August 1960) p. 508–512.
G.M. Goodwin, Advanced Materials & Processses, 133 (2) (1988) p. 48–50.
C.D. Lundin and D.F. Spond, Welding J. (November 1976) p. 356s–367s.
M.J. Strum, unpublished research, Lawrence Livermore National Laboratory, 1987.
M. Kurup, A. Tauqir, and P. Strutt, (Mater. Res. Soc. Symp. Proc. 28, Elsevier Science Publishing Co., 1984) p. 93–98.
A. Gasser and G. Herziger et al., Laser Advanced Materials Processing-Science and Applications, May 21–23, 1987, Osaka, Japan, p. 441–446.
J. Huang and E.N. Kaufmann, unpublished research, Lawrence Livermore National Laboratory, 1986.
A. Matsunawa, S. Katayama, Y. Ohmi, and T. Kuroki, Laser Advanced Materials Processing-Science and Applications, May 21–23, 1987, Osaka, Japan, p. 441–446.
P.J.E. Monson, W.M. Steen, and D.R.F. West, ibid., p. 377–382.
A. Vannes, J. Hernandez, and L. Maiffredy et al., ibid., p. 371–376.
D. Rosenthal, Trans. ASME 68 (1946) p. 849–865.
E.G. Signes, Welding J. (October 1972) p. 473s.
O.W. Blodgett, Welding J. (March 1984) p. 19.
S.S. Glickstein and E. Friedman, Welding J. (September 1984) p. 38.
S.C. Hsu, S. Chakravorty, and R. Mehrabian, Met. Trans. 9B (1978) p. 221.
J.A. Sekhar, S. Kou, and R. Mehrabian, Met. Trans. 14A (1983) p. 1169.
S. Kou, Met. Trans. B (March 1982) p. 363–371.
A.B. Shapiro, TOPAZ-2D, UCID-20045, Lawrence Livermore National Laboratory, 1984.
A.B. Shapiro, TOPAZ-3D, UCID-20484, Lawrence Livermore National Laboratory, August 1985.
K.W. Mahin, A.B. Shapiro, and J. Hallquist, SAND86-8671, Sandia Livermore Laboratory, (December 1986); also in Advances in Welding Science and Technology, edited by S.A. David (ASM Intl., 1986) p. 215.
R.J. Wallace and E.N. Kaufmann, J. Mater. Res. 1 (1986) p. 27.
J.S. Huang and E.N. Kaufmann, UCRL-96625, April 1987, submitted to J. Mater. Res.
J. Goldak, B. Patel, M. Bibby, and J. Moore, NATO AGARD Conference Proceedings, Vol. 398, September 1, 1985, p. 1–32.
Nunsian Tsai, PhD thesis, Massachusetts Institute of Technology, April 1983.
J. Goldak, A. Chakravarri, and M. Bibby, Met. Trans. 15B (1984) p. 299.
G.M. Oreper, J. Szekely, and T.W. Eagar, Met. Trans. 17B (December 1986) p. 735–744.
C.R. Heiple and J.R. Roper, Welding J. (April 1982) p. 97-S.
G.S. Mills, Welding J. (January 1979) p. 21s–24s.
A. Block-Bolten and T.W. Eagar, Met. Trans. 15B (September 1984) p. 461–469.
Xin-Cheng Wei, MS UC Davis, 1983.
J.E. Agapakis and K. Masubuchi, Welding J. (June 1984) p. 187–195.
L. Karlsson, in Thermal Stresses I, edited by R.B. Hetnarski (Elsevier Science Publishing Co., 1986) p. 300–389.
A.B. Shapiro, UCRL-94627, Lawrence Livermore National Laboratory, May 1986.
J.O. Hallquist, NIKE2D, UC1D-19677, Rev. 1, Lawrence Livermore National Laboratory, December 1986.
J.O. Hallquist, NIKE3D, UC1D-18822, Lawrence Livermore National Laboratory, January 1981.
Welding Technology, 8th edition, Vol. 1, Welding Handbook, (American Welding Society, 1987).
C.D. Lundin, A.C. Lingenfelter, G.E. Grotke, and G.G. Lessmann, Welding Research Council Bulletin No. 280, (August 1982).
Author information
Authors and Affiliations
Additional information
Michael J. Strum received his PhD in materials science from the University of California at Berkeley in 1987. He is currently pursuing surface processing and joining studies as a metallurgist in the Chemistry and Materials Science Department, Lawrence Livermore National Laboratory.
Rights and permissions
About this article
Cite this article
Strum, M.J. Hot Cracking in Directed-Energy Surface Processing. MRS Bulletin 13, 33–37 (1988). https://doi.org/10.1557/S0883769400065660
Published:
Issue Date:
DOI: https://doi.org/10.1557/S0883769400065660