Abstract
The influence of microstructure on the indentation cracking behavior of molybdenum disilicide (MoSi2) has been examined. The indentation response of samples produced by various methods has been measured to examine the elastic/plastic nature, hardness, and fracture toughness. Fracture toughness comparisons were made by measuring indentation crack lengths, observing the elastic/plastic indentation response, and quantifying the differences in the indentation cracking behavior. Further information was gained by monitoring the acoustic activity during indentation for selected specimens. It has been observed that the fine grain size and the dispersion of the silica phase promote microcracking and crack deflection.
Similar content being viewed by others
References
D. M. Shah, D. Berczik, D. L. Anton, and R. Hecht, Mater. Sci. Eng. A155, 45–58 (1992).
A. K. Vasudevan and J. J. Petrovic, Mater. Sci. Eng. A155, 1–18 (1992).
E. Fitzer and W. Remmale, in Proc. 5th Int. Conf. on Composite Materials, ICCM-V (Am. Inst. Min. Engrs., Philadelphia, PA, 1985), pp. 143–156.
R.K. Wade and J. J. Petrovic, J. Am. Ceram. Soc. 75 (6), 1682–1684 (1992).
D.A. Hardwick, P. L. Martin, and R. J. Moores, Scripta Metall. Mater. 27, 391–394 (1992).
S.C. Deevi, J. Mater. Sci. 26, 3343–3353 (1991).
S. Sampath and H. Herman, in High Temperature Silicides and Refractory Alloys, edited by C. L. Briant, J. J. Petrovic, B. P. Bewlay, A. K. Vasudevan, and H. A. Lipsitt (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 71–80.
R. M. Aikin, Jr., Scripta Metall. Mater. 26, 1025–1030 (1992).
D. A. Hardwick, P. L. Martin, and R. J. Moores, Scripta Metall. Mater. 27, 391–394 (1992).
J. D. Cotton, Y. S. Kim, and M. J. Kaufman, Mater. Sci. Eng. A144, 287–291 (1991).
A. Costa e Silva and M. J. Kaufman, Met. Trans. A 25A (1), 5–15 (1994).
T. C. Chou and T. G. Nieh, J. Mater. Res. 8, 214–226 (1993).
S. Maloy, A. H. Heuer, J. Lewandowski, and J. Petrovic, J. Am. Ceram. Soc. 74 (10), 2704–2706 (1991).
F. W. Vahldiek and S. A. Mersol, J. Less-Comm. Met. 15, 165–176 (1968).
P. H. Boldt, J.D. Embury, and G. C. Weatherly, Mater. Sci. Eng. A155, 251–258 (1992).
K. Ito, H. Inui, Y. Shirai, and M. Yamaguchi, Philos. Mag. A 72 (4), 1075–1097 (1995).
M. Hebsur, in Intermetallic Matrix Composites III, edited by J. A. Graves, R. R. Bowman, and J.J. Lewandowski (Mater. Res. Soc. Symp. Proc. 350, Pittsburgh, PA, 1994), pp. 77–182.
J. J. Petrovic and R. E. Honnell, J. Mater. Sci. Lett. 9, 1083–1084 (1990).
R. M. Aikin, Jr., in Ceram. Eng. Sci. Proc., 15th Annual Conference on Composites and Advanced Ceramic Materials, edited by J. B. Wachtman (American Ceramic Society, Westerville, OH, 1991), Vol. 12, No. 9–10, pp. 1643–1655.
J. J. Petrovic, A. K. Bhattacharya, R. E. Honnell, T. E. Mitchell, R. K. Wade, and K. J. McClellan, Mater. Sci. Eng. A155, 259–266 (1992).
R. Gibala, H. Chang, and C.M. Czarnik, in High Temperature Silicides and Refractory Alloys, edited by C. L. Briant, J. J. Petrovic, B. P. Bewlay, A. K. Vasudevan, and H. A. Lipsitt (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 175–184.
I. Baker and P. R. Munroe, J. Met. 40 (2), 28–31 (1988).
R. Darolia, D. Lahrman, and R. Field, Scripta Metall. et Mater. 26, 1007–1012 (1992).
M. Yamaguchi and Y. Umakoshi, Prog. Met. Sci. 34, 22,118 (1990).
Y. Umakoshi, T. Hirano, T. Sakagami, and T. Yamane, in High Temperature Aluminides and Intermetallics, edited by S. Whang, C. Liu, D. Pope, and J. Stiegler (TMS, Warrendale, PA, 1990), pp. 111–129.
A. Stergiou and P. Tsakiropoulos, in High Temperature Ordered Alloys VI, edited by J. A. Horton, I. Baker, S. Hanada, R. D. Noebe, and D. S. Schwartz (Mater. Res. Soc. Symp. Proc. 364, Pittsburgh, PA, 1995), pp. 911–916.
S. Chin, D. L. Anton, and A. F. Giamei, in High Temperature Silicides and Refractory Alloys, edited by C.L. Briant, J. J. Petrovic, B.P. Bewlay, A. K. Vasudevan, H. A. Lipsitt (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 423–429.
D. L. Davidson and A. Bose, in High Temperature Silicides and Refractory Alloys, edited by C. L. Briant, J. J. Petrovic, B. P. Bewlay, A. K. Vasudevan, and H. A. Lipsitt (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 431–436.
D. B. Marshall, T. Noma, and A. G. Evans, J. Am. Ceram. Soc. 65 (10), C175–176 (1982).
W.C. Oliver and G. M. Pharr, J. Mater. Res. 7, 1565–1570 (1992).
G. R. Anstis, P. Chantikul, B. R. Lawn, and D. B. Marshall, J. Am. Ceram. Soc. 64 (9), 533–538 (1981).
A. Newman, S. Sampath, and H. Herman, in Processing and Design Issues in High Temperature Materials, edited by N. S. Stoloff and R.H. Jones (The Minerals, Metals, and Materials Society, Warrendale, PA, 1997), pp. 403–412.
J. J. Petrovic and R. E. Honnell, J. Mater. Sci. 25, 4453–4456 (1990).
R. Tiwari, H. Herman, and S. Sampath, Mater. Sci. Eng. A155, 95–100 (1992).
A.K. Bhattacharya and J. J. Petrovic, J. Am. Ceram. Soc. 74 (10), 2700–2703 (1991).
S.B. Bhaduri and R. Radhakrishnan, in Advances in Powder Metallurgy & Particulate Materials, Vol. 9, edited by J. M. Capus and R. M. German (Particulate Materials and Processes, Vol. 9, American Powder Metallurgy Institute, Princeton, NJ, 1992), pp. 369–379.
R.G. Castro, R. W. Smith, A. D. Rollett, and P. W. Stanek, Scripta Metall. et Mater. 26, 207–212 (1992).
R.K. Wade and J. J. Petrovic, J. Am. Ceram. Soc. 75 (11), 3160–3162 (1992).
Y.L. Jeng, J. Wolfenstine, and E.J. Lavernia, Scripta Metall. et Mater. 28, 453–458 (1993).
S. Jayashankar, S. E. Riddle, and M. J. Kaufman, in High Temperature Silicides and Refractory Alloys, edited by C.L. Briant, J. J. Petrovic, B. P. Bewlay, A.K. Vasudevan, and H. A. Lipsitt (Mater. Res. Soc. Symp. Proc. 322, Pittsburgh, PA, 1994), pp. 33–40.
K.T. Faber and A. G. Evans, J. Am. Ceram. Soc. 66, C94–96 (1983).
C.B. Scruby, C. Jones, J. M. Titchmarsh, and H. N.G. Wadley, Metal Science 15, 241–261 (1981).
A.G. Evans and M. Linzer, J. Am. Ceram. Soc. 56, 575–580 (1973).
E.M. Schulson, Res. Mech. Lett. 1, 111 (1981).
D.J. Gaydosh, R. W. Jech, and R. H. Titran, J. Mat. Sci. Lett. 4, 138 (1985).
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Newman, A., Jewett, T., Sampath, S. et al. Indentation Response of Molybdenum Disilicide. Journal of Materials Research 13, 2662–2671 (1998). https://doi.org/10.1557/JMR.1998.0371
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/JMR.1998.0371