Skip to main content
SpringerLink
Log in

Contact Area Evolution During an Indentation Process

  • Articles
  • Published:
Journal of Materials Research Aims and scope Submit manuscript

Abstract

The evolution of the contact area during an indentation process has been examined by an ac technique and also by finite element analysis on five mechanically different materials. Constant contact area regimes were observed during the initial unloading stage and the duration of that regime depends strongly on material properties. The consistency of the results obtained by the two approaches not only proves the validity and advantage of the ac indentation technique but also confirms the applicability of contact stiffness equation. The influence of a hardness impression on unloading characteristics has also been clearly demonstrated by numerically simulating a reloading process.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. F. Frolich, P. Grau, and W. Grellmann, Phys. Status Solidi (a) 42, 79–89 (1977).

    Article  Google Scholar 

  2. D. Newey, M. A. Wilkins, and H. M. Pollock, J. Phys. E: Sci. Instrum. 15, 119–122 (1982).

  3. J. Pethica, R. Hutchings, and W. C. Oliver, Philos. Mag. A 48, 593 (1983).

  4. I. N. Sneddon, Int. J. Eng. Sci. 3, 47–57 (1965).

  5. G. M. Pharr, W. C. Oliver, and F. R. Brotzen, J. Mater. Res. 7, 613–617 (1992).

  6. R. B. King, Int. J. Solids Struct. 3, 1657 (1987).

  7. S. I. Bulychev, V. P. Alekhin, M. Kh. Shorshorov, A. P. Ternovskii, and G. D. Shnyrev, Zavod. Lab. 41, 1137 (1975).

  8. M. F. Doerner and W. D. Nix, J. Mater. Res. 1, 601–609 (1986).

  9. W. C. Oliver and G. M. Pharr, J. Mater. Res. 7, 1564–1583 (1992).

  10. T. A. Laursen and J. C. Simo, J. Mater. Res. 7, 618–626 (1992).

  11. J. B. Pethica and W. C. Oliver, in Thin Films: Stresses and Mechanical Properties, edited by J. C. Bravman, W. D. Nix, D. M. Barnett, and D. Smith (Mater. Res. Soc. Symp. Proc. 130, Pittsburgh, PA, 1989), pp. 13–23.

  12. T. W. Wu, Mater. Chem. Phys. 33, 15–30 (1993).

  13. T. W. Wu, J. Mater. Res. 6, 407–426 (1991).

    Article  Google Scholar 

  14. A. Bolshakov and G. M. Pharr, in Thin Films: Stresses and Mechanical Properties VI, edited by W. W. Gerberich, H. Gao, J-E. Sundgren, and S. P. Baker (Mater. Res. Soc. Symp. Proc. 146, Pittsburgh, PA, 1996).

Download references

Author information

Authors and Affiliations

  1. Materials Science Program, Department of Mechanical Engineering, University of Rochester, Rochester, New York, 14627, USA

    Kangjie Li & J. C. M. Li

  2. IBM Research Division, Almaden Research Center, San Jose, California, 95120, USA

    T. W. Wu

Authors
  1. Kangjie Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. T. W. Wu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. J. C. M. Li
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Li, K., Wu, T.W. & Li, J.C.M. Contact Area Evolution During an Indentation Process. Journal of Materials Research 12, 2064–2071 (1997). https://doi.org/10.1557/JMR.1997.0277

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1557/JMR.1997.0277

Search

Navigation