Abstract
The outgassing behavior and mechanical properties of polysiloxane based and phosphorus doped silicate based films as planarization candidates for device processing were evaluated using various analytical techniques. After curing between 370 °C and 450 °C, a high temperature rebake above 410 °C caused twice the weight loss in polysiloxane based films as in silicate films. This means that further outgassing, which could occur to a greater degree from polysiloxane than from silicate, could lead to a more probable blistering within the interlayer of the sandwiched spin-on-glass (SOG) during subsequent thermal processing. However, a well-cured polysiloxane would be a better candidate for planarization applications because the film was found to absorb less moisture and had lower stress than the silicate. Due to high silanol content and high porosity in silicate, it was found to absorb six times more water than polysiloxane. When water evolved, significantly higher stress levels were observed in silicate than in polysiloxane during thermal cycle tests. Infrared spectroscopic analysis revealed that polysiloxane contained Si–O–CH3 moiety, which rendered the film flexible, while silicate contained near-stoichiometric SiO2 bonds, which made for a more rigid and dense structure. This difference in the film structures translated to three times higher stress in silicate than in polysiloxane. During device processing, it was seen that silicate films were more prone to cracking than polysiloxane films. The components of the outgassing materials were either volatile organic species from residual solvents not completely burned out during cure, or carbon dioxide and water vapor as by-products from further cure. Gas chromatography indicated that both types of films contained volatile organic residues when cured at 370 °C. However, at 410 °C, volatile organic species were present in the polysiloxane but not in the silicate. A 30 to 60 min cure at temperature greater than 410 °C was then found to adequately cure polysiloxane. It was concluded that a “well cured” polysiloxane based spin-on-glass (SOG) would be more suitable than a silicate based SOG for planarization application.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
C. Chiang, N. V. Lam, J. K. Chu, N. Cox, J. Fraser, J. Bozarth, and B. Mumford, V-MIC Conf. IEEE, 404 (1987).
C. H. Ting, H. Y. Lin, P. L. Pai, and W. G. Oldham, V-MIC Conf. IEEE, 61 (1987).
H. G. Tompkins and C. J. Tracy, J. Electrochem. Soc. 136 (8), 2331–2335 (1989).
J. H. Shen and K. Klier, J. of Colloid and Interface Sci. 75 (1), 56–67 (1980).
D. L. Pavia, G. M. Lampman, and G. S. Kris, Introduction to Spectroscopy (Saunders Golden Sunburst Series), p. 77.
Y. Shacham-Diamond and Y. Nachumovsky, J. Electrochem. Soc . 137 (1), 190–196 (1990).
M. P. Woo, J. L. Cain, and C. Lee, J. Electrochem. Soc. 137 (1), 196–200 (1990).
D. L. W. Yen and G. K. Rao, V-MIC Conf. IEEE, 85 (1988).
J. K. Chu, J. S. Multani, S. K. Mittal, J. T. Orton, and R. Jecmen, V-MIC Conf. IEEE, 474 (1986).
Nitin Parekh, Robert Allen, William Yao, and Ron Fulks, in Proc. Symp. on Multilevel Metallization, Interconnection, and Contact Technologies, edited by L. B. Rothman (IBM Corporation, Yorktown Heights, NY, 1987) and T. Herdon (MIT Lincoln Laboratories, Lexington, MA, 1987), Vol. 87 (4), pp. 221–231.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Romero, J.D., Khan, M., Fatemi, H. et al. Outgassing behavior of spin-on-glass (SOG). Journal of Materials Research 6, 1996–2003 (1991). https://doi.org/10.1557/JMR.1991.1996
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1557/JMR.1991.1996