Skip to main content
SpringerLink
Log in

The use of β titanium alloys in the aerospace industry

  • Published:
Journal of Materials Engineering and Performance Aims and scope Submit manuscript

Abstract

Beta titanium alloys have been available since the 1950s (Ti-13V-11Cr-3Mo or B120VCA), but significant applications of these alloys, beyond the SR-71 Blackbird, have been slow in coming. The next significant usage of a β alloy did not occur until the mid-1980s on the B-1B bomber. This aircraft used Ti-15V-3Cr-3Al-3Sn sheet due to its capability for strip rolling, improved formability, and higher strength than Ti-6Al-4V. The next major usage was on a commercial aircraft, the Boeing 777, which made extensive use of Ti-10V-2Fe-3Al high-strength forgings. Ti-15V-3Cr-3Al-3Sn environmental control system ducting, castings, and springs were also used, along with Ti-3Al-8V-6Cr-4Mo-4Zr (β-C) springs. Beta-21S was also introduced for high-temperature usage. More recent work at Boeing has focused on the development of Ti-5Al-5Mo-5V-3Cr, a high-strength alloy that can be used at higher strength than Ti-10V-2Fe-3Al and is much more robust; it has a much wider, or friendlier, processing window. This, along with additional studies at Boeing, and from within the aerospace industry in general will be discussed in detail, summarizing applications and the rationale for the selection of this alloy system for aerospace applications.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. R.R. Boyer, Applications of Beta Titanium Alloys in Airframes,Beta Titanium Alloys in the 1990’s, D. Eylon, R.R. Boyer, and D.A. Koss, Ed., The Materials Society, 1993, p 335–346

  2. R.R. Boyer, Ti-10V-2Fe-3Al Properties,Beta Titanium Alloys in the 1980’s, R.R. Boyer and H.W. Rosenberg, Ed., Metallurgical Society of AIME, 1984, p 441–456

  3. K.-H. Rendigs, Titanium Products Used at AIRBUS,Ti-2003 Science and Technology, G. Lütjering and J. Albrecht, Ed., DGM, Wiley VCH, Weinheim, Germany, 2004, p 2659–2671

    Google Scholar 

  4. G. Terlinde and G. Fischer, Beta Titanium Alloys,Titanium’95: Science and Technology, P.A. Blenkinsop, W.J. Evans, and H.M. Flower, Ed., Institute of Materials, 1996, p 2177–2194

  5. C. Pepka, “Beta Alloy Springs in the 00’s, Renton,” presented at the Beta Titanium Alloys in the 00’s Symposium (San Francisco, CA), Annual Meeting of The Materials Society, February 2005

  6. A.M. Sherman and S.R. Seagle, Torsional Properties and Performance of Beta Titanium Alloy Automotive Suspension Springs,Beta Titanium Alloys in the 1980’s, R.R. Boyer and H.W. Rosenberg, Ed., AIME, Metallurgical Society of AIME, 1984, p 281–293

  7. G. Antoine, J. Panter, and M.-H. Campagnac, “Application of Ti-10-2-3 in Rotor Hub Parts of EUROCOPTER,” presented at the Beta Titanium Alloys in the 00’s Symposium (San Francisco, CA), Annual Meeting of The Materials Society, February 2005

  8. R.R. Boyer and G.W. Kuhlman, Processing Properties Relationships of Ti-10V-2Fe-3Al,Metall. Trans. A, Vol 18 (No. 12), 1987, p 2095–2103

    Article  Google Scholar 

  9. J.C. Fanning and R.R. Boyer,Ti-2003 Science and Technology, Wiley VCH, Weinheim, Germany, 2004, p 2643

    Google Scholar 

  10. J. Panter, A. Dallz, K.-H. Rendigs, N. Hellard, and W. Gerhard, “Influence of Thermo-Mechanical Treatments on Microstructure and Mechanical Properties of Near Beta Titanium Alloy VST 55531,” presented at the Beta Titanium Alloys in the 00’s Symposium, Annual Meeting of The Materials Society (San Francisco, CA), February 2005

  11. S. Veeck, D. Lee, R. Boyer, and R. Briggs, The Castability of Ti-5553 Alloy: Its Microstructure and Properties,Advanced Materials & Processes, Vol 162 (No. 10), 2004, p 47–49

    Google Scholar 

  12. S. Buzolits, Tough Titanium Fasteners,Advanced Materials & Processes, Vol 161 (No. 11), 2003, p 53

    Google Scholar 

  13. S. Buzolits and SPS Laboratories, Philadelphia, PA, “SPS M761 Titanium Alloy: A New Fastener Alloy to Replace Alloy Steel and CRES,” paper presented at Aeromat 2004 (Seattle, WA), June 7–10, 2004

  14. P.J. Bania, TiPro (Henderson, NV), personal communication, 2004

Download references

Author information

Authors and Affiliations

  1. The Boeing Company, 98124, Seattle, WA

    R. R. Boyer & R. D. Briggs

Authors
  1. R. R. Boyer
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. R. D. Briggs
    View author publications

    You can also search for this author in PubMed Google Scholar

Rights and permissions

Reprints and permissions

About this article

Cite this article

Boyer, R.R., Briggs, R.D. The use of β titanium alloys in the aerospace industry. J. of Materi Eng and Perform 14, 681–685 (2005). https://doi.org/10.1361/105994905X75448

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1361/105994905X75448

Keywords

Search

Navigation