Microstructure design and heat treatment selection for casting alloys using the quality index

  • C. H. Cáceres
Article
First Online:
Received:
Revised:

Abstract

The ductility of casting alloys is usually low and it is thus important to simultaneously assess the effect of changes to the microstructure and heat treatment on both ductility and strength of the material. The use for this purpose of the quality index charts* is common in the casting industry with regard to the Al-Si-Mg casting alloys A356 and A357.

An analytical method of generating quality index charts for any alloy system is presented. Applications of the method are illustrated with case studies involving Al-Si-Mg, Mg-Al-Zn, and Al-Si-Cu-Mg casting alloys. The analytically determined charts indicate the limits to microstructural improvement available for each material. The possibility of using the charts to optimize the relation between mechanical performance, chemical composition, solidification conditions, and temper is discussed.

Keywords

casting Al-Si-Mg alloys Mg-Al-Zn alloys Al-Cu-Si alloys strength ductility heat treatment 
This is a preview of subscription content, log in to check access.

Preview

Unable to display preview. Download preview PDF.

Unable to display preview. Download preview PDF.

References

  1. 1.
    M. Drouzy, S. Jacob, and M. Richard: AFS Int. Cast Met. J., 1980, vol. 5, pp. 43–50.Google Scholar
  2. 2.
    C.H. Cáceres: Int. J. Cast Met. Res., 1998, vol. 10, pp. 293–99.CrossRefGoogle Scholar
  3. 3.
    C.H. Cáceres, T. Din, A.K.M.B. Rashid, and J. Campbell: Mater. Sci. Technol., 1999, vol. 15, pp. 711–16.CrossRefGoogle Scholar
  4. 4.
    C.H. Cáceres: AFS Trans., 1998, vol. 106, pp. 601–04.Google Scholar
  5. 5.
    C.H. Cáceres, J.H. Sokolowski, and P. Gallo: Mater. Sci. Eng. A, 1999, vol. 271, pp. 53–61.CrossRefGoogle Scholar
  6. 6.
    C.H. Cáceres, L. Wang, D. Apelian, and M. Makhlouf: AFS Trans., 1999, vol. 107.Google Scholar
  7. 7.
    G.E. Dieter: Mechanical Metallurgy, 3rd ed., McGraw-Hill, New York, NY, 1986, pp. 290.Google Scholar
  8. 8.
    C.H. Cáceres: Int. J. Cast Met. Res., Vol. 12, 2000, in press.Google Scholar
  9. 9.
    C.H. Cáceres and J. Barresi: Int. J. Cast Met. Res., vol. 12, 2000, in press.Google Scholar
  10. 10.
    S. Shivkumar, C. Keller, and D. Apelian: AFS Trans., 1990, vol. 98, pp. 905–10.Google Scholar
  11. 11.
    J. Barresi, M.J. Kerr, H. Wang, and M.J. Couper: AFS Trans., vol. 108, 2000, in press.Google Scholar
  12. 12.
    B. Closset and J.E. Gruzleski: Metall. Trans. A, 1982, vol. 13A, pp. 945–51.CrossRefGoogle Scholar
  13. 13.
    G.E. Nagel, J.P. Mouret, and J. Dubruelh: AFS Trans., 1983, vol. 91, pp. 157–60.Google Scholar
  14. 14.
    C.H. Cáceres, C.J. Davidson, J.R. Griffiths, and Q.G. Wang: Metall. Mater. Trans. A, 1999, vol. 30A, pp. 2611–18.CrossRefGoogle Scholar
  15. 15.
    Q.G. Wang, C.H. Cáceres, and J.R. Griffiths: AFS Trans., 1998, vol. 106, pp. 131–36.Google Scholar
  16. 16.
    D.A. Granger, R.R. Sawtell, and M.M. Kersker: AFS Trans., 1984, vol. 92, pp. 579–86.Google Scholar
  17. 17.
    C.L. Bancroft, C.H. Cáceres, and J.R. Griffiths: Proc. Magnesium Technology 2000 Int. Conf., Nashville, TN, Mar. 2000.Google Scholar
  18. 18.
    C.H. Cáceres, C.L. Bancroft, J.R. Griffiths, and C.J. Davidson: 2000, in preparation.Google Scholar
  19. 19.
    R. Smith, C.H. Cáceres, and D. StJohn: Materials Research 96, IMMA Conf. Proc., Brisbane, July 1996, The Institute of Metals and Materials Australasia, Brisbane, 1996, vol. 3, pp. 140–43.Google Scholar
  20. 20.
    T. Din, A.K.M.B. Rashid, and J. Campbell: Mater. Sci. Technol., 1996, vol. 12, pp. 269–73.CrossRefGoogle Scholar
  21. 21.
    J.M. Dowling and J.W. Martin: Acta Metall., 1976, vol. 24, pp. 1147–53.CrossRefGoogle Scholar
  22. 22.
    K. Banizs: Mater. Sci. Eng. A, 1979, vol. A41, pp. 17–24.CrossRefGoogle Scholar
  23. 23.
    L. Zhen and S.B. Kang: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 1489–97.CrossRefGoogle Scholar
  24. 24.
    R.E. Stoltz and R.M. Pelloux: Metall. Trans., 1976, vol. 7A, pp. 1295–1306.CrossRefGoogle Scholar
  25. 25.
    W. Reif, J. Dutkiewicz, R. Ciach, S. Yu, and J. Krol: Mater. Sci. Eng. A, 1997, vol. A224–A236, pp. 165–68.CrossRefGoogle Scholar
  26. 26.
    M.F. Ashby: in Strengthening Methods in Crystals, A. Kelly and R.B. Nicholson, eds., Elsevier, Amsterdam, 1971, ch. 3.Google Scholar

Copyright information

© ASM International 2000

Authors and Affiliations

  • C. H. Cáceres
    • 1
  1. 1.CRC for Alloy and Solidification Technology (CAST), Department of Mining, Minerals and Materials EngineeringThe University of QueenslandBrisbaneAustralia

Personalised recommendations