Abstract
Lattice spacings of layer silicates, particularly clay minerals, may exceed 20 Å. The errors in measuring lattice spacings increase rapidly for spacings greater than about 10 Å and diffraction angles 2θ less than about 10°. Long-chain organic compounds, such as normal alcohols, C14–C20, and normal alkanes (paraffins), C26–C30, provide useful calibrations for lattice spacings in the range 10–50Å. The basal spacings of the calibrating substances are determined from their higher order reflections in the angular range where reflections from quartz and silicon are used as standards.
Résumé
Les espacements réticulaires des phyllosilicates, en particulier les minéraux argileux, peuvent dépasser 20 Å. Les erreurs commises dans la mesure de ces espacements augmentent rapidement pour des espacements supérieurs à 10 Å et des angles de diffraction 2 θ inférieurs à 10° environ. Des composés organiques à longue chaîne tels que les alcools normaux de C14–C20 et les alcanes normaux (paraffines) de C26–C30, constituent des étalons utiles pour les espacements réticulaires compris entre 10–50 Å. Les distances basales de ces substances étalons sont déterminées à partir de leurs ordres de réflexion supérieurs dans le domaine angulaire où les réflexions du quartz et de la silice sont utilisées comme standard.
Kurzreferat
Basisebenenabstände von Schichtsilicaten, besonders von Tonmineralen, können 20 Å übersteigen. Die Fehler bei der Messung nehmen bei Basisebenenabständen über 10 Å und Beugungswinkels 2θ kleiner als etwa 10° schnell zu. Langkettige organische Verbindungen wie normale Alkohole, C14–C20, und normale Alkane (Paraffine), C26–C30, stellen nützliche Eichsubstanzen für Schichtabstände im Bereich von 10–50 Å dar. Die Basisebenenabstände der Eichsubstanzen werden aus den Beugungslinen höherer Ordnung in dem Winkelbereich bestimmt, in dem die Reflexe von Quarz und Silicium als Standards benutzt werden.
Резюме
Периоды решетки слоистых силикатов, особенно глинистых минералов, могут превышать 20 А. При измерении периодов решетки часто возникают ошибки, которые возни-кают даже чаще, если периоды решетки примерно более 10 Å, а углы отклонения при диффрак-ции 2θ, менее приблизительно 10°. Органические соединения с длинными цепями, такие как стандартные спирты, С14–С20, и стандартные алканы (парафины), С26–С30, предоставляют приемлемую калибровку для периодов решетки в пределах 10–50 Å. Основные периоды решетки веществ применяемых для калибровки определяются по их более высокому порядку отражения в угловом радиусе, где отражения кварца и кремния используются в качестве эталонов.
Similar content being viewed by others
References
Abrahamsson, S., Larsson, G. and von Sydow, E.(1960) The crystal structure of the monoclinic form of n-hexadecanol: Acta Cryst. 13, 770–774.
Broadhurst, M. G. (1962) An analysis of the solid phase behavior of the normal paraffins: J. Res. Nat. Bur. Stds 66A, 241–249.
Keith, H. D. (1955) Lattice spacings in clear crystalline quartz and their variability: Am. Mineral. 40, 530–534.
Kittrick, J. A. (1960) Cholesterol as a standard in the X-ray diffraction of clay minerals: Proc. Am. Soil Sci. Soc. 24, 17–20.
Nyburg, S. C. and Potworowski, J. A. (1973) Prediction of unit cells and atomic coordinates for the n-alkanes: Acta Cryst. B29, 347–352.
Reynolds, R. C. (1968) The effect of particle size on apparent lattice spacings. Acta Cryst. A24, 319.
Robertson, J. M. (1953) Organic Crystals and Molecules. Cornell University Press, New York.
Ross, M. (1968) X-ray diffraction effects by non-ideal crystals of biotite, muscovite, montmorillonite, mixed-layer clays, graphite and periclase: Z. Kristallog. 126, 80–97.
Sudo, T. and Hayashi, H. (1955) New types of clay minerals with long spacings at about 30 A: Sci. Rep. Tokvo Kyoiku Daigaku, Sect. C., No. 25, 281–316.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Brindley, G.W., Wan, H.M. Use of Long-Spacing Alcohols and Alkanes for Calibration of Long Spacings from Layer Silicates, Particularly Clay Minerals. Clays Clay Miner. 22, 313–317 (1974). https://doi.org/10.1346/CCMN.1974.0220402
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1346/CCMN.1974.0220402