Abstract
During the last decade, the pharmaceutical industry has shown a growing interest in continuous twin-screw granulation (TSG). Despite flourishing literature on TSG, limited studies focused on fundamental process understanding on its mechanisms. In current study, granule quality attributes along the length of the TSG barrel were evaluated together with heat transfer in order to achieve a more fundamental understanding of the granulation process. An experimental setup was developed allowing the collection of granules at the different TSG compartments. In addition to the determination of typical granule attributes, mechanical energy, barrel and granule temperature (measured using an in-line implemented infra-red camera) were measured to evaluate heat transfer occurring at the different compartments and to relate them to granulation mechanisms. Collected data identified wetting enthalpy and friction forces as the main sources of heat along the granulator length. Wetting occurred in the wetting zone and generated temperature increase depending on liquid-to-solid ratio and powder wettability. In the kneading zones, granule temperature increase was proportional to mechanical energy. While it is usually admitted that granule consolidation and reshaping are the consequence of the high shear experienced by the granules, it was highlighted that most of the mechanical energy is converted into thermal energy with no correlation between mechanical energy and granule size distribution. Combined mass and energy balance of the granulation process are therefore necessary to capture the interaction between granule properties and physico-chemical and mechanical phenomena occurring in each compartment.
Similar content being viewed by others
References
Vervaet C, Vercruysse J, Remon JP, Beer TD. Continuous Processing of Pharmaceuticals. In: Encyclopedia of Pharmaceutical Science and Technology, Fourth Edition. Taylor & Francis; 2013 [cited 2015 Feb 16]. p. 644–55. Available from: http://www.tandfonline.com/doi/abs/10.1081/E-EPT4-120050224.
Lee SL, O’Connor TF, Yang X, Cruz CN, Chatterjee S, Madurawe RD, et al. Modernizing pharmaceutical manufacturing: from batch to continuous production. J Pharm Innov. 2015;10(3):191–9.
Leuenberger H. New trends in the production of pharmaceutical granules: batch versus continuous processing. Eur J Pharm Biopharm. 2001;52(3):289–96.
Srai JS, Badman C, Krumme M, Futran M, Johnston C. Future supply chains enabled by continuous processing--opportunities and challenges. May 20-21, 2014 continuous manufacturing symposium. J Pharm Sci. 2015;104(3):840–9.
Chatterjee F. FDA perspective on continuous manufacturing. IFPAC Annual meeting. Baltimore; 2012.
Madurawe RD. Continuous manufacturing: FDA perspective. E55/ASTM/FDA workshop. FDA White Oak Campus. Silver Spring, MD, USA; 2016.
Vercruysse J, Córdoba Díaz D, Peeters E, Fonteyne M, Delaet U, Van Assche I, et al. Continuous twin screw granulation: influence of process variables on granule and tablet quality. Eur J Pharm Biopharm. 2012;82(1):205–11.
Dhenge RM, Fyles RS, Cartwright JJ, Doughty DG, Hounslow MJ, Salman AD. Twin screw wet granulation: granule properties. Chem Eng J. 2010;164(2–3):322–9.
Fonteyne M, Wickström H, Peeters E, Vercruysse J, Ehlers H, Peters B-H, et al. Influence of raw material properties upon critical quality attributes of continuously produced granules and tablets. Eur J Pharm Biopharm. 2014;87(2):252–63.
Dhenge RM, Cartwright JJ, Hounslow MJ, Salman AD. Twin screw wet granulation: effects of properties of granulation liquid. Powder Technol. 2012;229:126–36.
Barrasso D, El Hagrasy A, Litster JD, Ramachandran R. Multi-dimensional population balance model development and validation for a twin screw granulation process. Powder Technol. 2015;270(Part B):612–21.
Shirazian S, Darwish S, Kuhs M, Croker DM, Walker GM. Regime-separated approach for population balance modelling of continuous wet granulation of pharmaceutical formulations. Powder Technol. 2018;325:420–8.
Van Hauwermeiren D, Verstraeten M, Doshi P, am Ende MT, Turnbull N, Lee K, et al. On the modelling of granule size distributions in twin-screw wet granulation: calibration of a novel compartmental population balance model. Powder Technol. 2018 [cited 2018 Jul 20]; Available from: http://www.sciencedirect.com/science/article/pii/S0032591018303954.
Kumar A, Gernaey KV, Beer TD, Nopens I. Model-based analysis of high shear wet granulation from batch to continuous processes in pharmaceutical production – a critical review. Eur J Pharm Biopharm. 2013;85(3, Part B):814–32.
Kumar A, Vercruysse J, Bellandi G, Gernaey KV, Vervaet C, Remon JP, et al. Experimental investigation of granule size and shape dynamics in twin-screw granulation. Int J Pharm. 2014;475(1–2):485–95.
Dhenge RM, Cartwright JJ, Hounslow MJ, Salman AD. Twin screw granulation: steps in granule growth. Int J Pharm. 2012;438(1–2):20–32.
Verstraeten M, Van Hauwermeiren D, Lee K, Turnbull N, Wilsdon D, Am Ende M, et al. In-depth experimental analysis of pharmaceutical twin-screw wet granulation in view of detailed process understanding. Int J Pharm. 2017;529(1–2):678–93.
Kumar A, Dhondt J, Vercruysse J, De Leersnyder F, Vanhoorne V, Vervaet C, et al. Development of a process map: a step towards a regime map for steady-state high shear wet twin screw granulation. Powder Technol. [cited 2016 Jan 4]; Available from: http://www.sciencedirect.com/science/article/pii/S0032591015302102.
Tu W-D, Ingram A, Seville J. Regime map development for continuous twin screw granulation. Chem Eng Sci. 2013;87:315–26.
Dhenge RM, Washino K, Cartwright JJ, Hounslow MJ, Salman AD. Twin screw granulation using conveying screws: effects of viscosity of granulation liquids and flow of powders. Powder Technol. 2013;238:77–90.
Fonteyne M, Vercruysse J, Díaz DC, Gildemyn D, Vervaet C, Remon JP, et al. Real-time assessment of critical quality attributes of a continuous granulation process. Pharm Dev Technol. 2013;18(1):85–97.
Buckton G, Beezer AE. A microcalorimetric study of powder surface energetics. Int J Pharm. 1988;41(1):139–45.
El Hagrasy AS, Hennenkamp JR, Burke MD, Cartwright JJ, Litster JD. Twin screw wet granulation: influence of formulation parameters on granule properties and growth behavior. Powder Technol. 2013;238:108–15.
Kumar A, Alakarjula M, Vanhoorne V, Toiviainen M, De Leersnyder F, Vercruysse J, et al. Linking granulation performance with residence time and granulation liquid distributions in twin-screw granulation: an experimental investigation. Eur J Pharm Sci. [cited 2016 Jan 4]; Available from: http://www.sciencedirect.com/science/article/pii/S0928098715300956
Vercruysse J, Burggraeve A, Fonteyne M, Cappuyns P, Delaet U, Van Assche I, et al. Impact of screw configuration on the particle size distribution of granules produced by twin screw granulation. Int J Pharm. 2015;479(1):171–80.
Kim S-H, Hwang K-M, Cho C-H, Nguyen T-T, Seok SH, Hwang K-M, et al. Application of continuous twin screw granulation for the metformin hydrochloride extended release formulation. Int J Pharm. 2017;529(1):410–22.
Fonteyne M, Correia A, De Plecker S, Vercruysse J, Ilić I, Zhou Q, et al. Impact of microcrystalline cellulose material attributes: a case study on continuous twin screw granulation. Int J Pharm. 2015;478(2):705–17.
Pradhan SU, Sen M, Li J, Litster JD, Wassgren CR. Granule breakage in twin screw granulation: effect of material properties and screw element geometry. Powder Technol. 2017;315:290–9.
Iveson SM, Litster JD. Growth regime map for liquid-bound granules. AICHE J. 1998;44(7):1510–8.
Liu LX, Smith R, Litster JD. Wet granule breakage in a breakage only high-hear mixer: effect of formulation properties on breakage behaviour. Powder Technol. 2009;189(2):158–64.
Barrasso D, Eppinger T, Pereira FE, Aglave R, Debus K, Bermingham SK, et al. A multi-scale, mechanistic model of a wet granulation process using a novel bi-directional PBM–DEM coupling algorithm. Chem Eng Sci. 2015;123:500–13.
Vonk P, Guillaume CPF, Ramaker JS, Vromans H, Kossen NWF. Growth mechanisms of high-shear pelletisation. Int J Pharm. 1997;157(1):93–102.
Holman J. Assessing the use of twin screw wet granulation in a multi stage manufacturing process for the continuous production of pharmaceutical products [PhD thesis]. [Surrey]: University of Surrey; 2013.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Fanny Stauffer and Alexander Ryckaert are shared first authorship
Electronic supplementary material
ESM 1
(XLSX 12 kb)
Rights and permissions
About this article
Cite this article
Stauffer, F., Ryckaert, A., Van Hauwermeiren, D. et al. Heat Transfer Evaluation During Twin-Screw Wet Granulation in View of Detailed Process Understanding. AAPS PharmSciTech 20, 291 (2019). https://doi.org/10.1208/s12249-019-1483-z
Received:
Accepted:
Published:
DOI: https://doi.org/10.1208/s12249-019-1483-z