Production of xylooligosaccharides and monosaccharides from poplar by a two-step acetic acid and peroxide/acetic acid pretreatment



Populus (poplar) tree species including hybrid varieties are considered as promising biomass feedstock for biofuels and biochemicals production due to their fast growing, short vegetative cycle, and widely distribution. In this work, poplar was pretreated with acetic acid (AC) to produce xylooligosaccharides (XOS), and hydrogen peroxide–acetic acid (HPAC) was used to remove residual lignin in AC-pretreated poplar for enzymatic hydrolysis. The aim of this work is to produce XOS and monosaccharides from poplar by a two-step pretreatment method.


The optimal conditions for the AC pretreatment were 170 °C, 5% AC, and 30 min, giving a XOS yield of 55.8%. The optimal HPAC pretreatment conditions were 60 °C, 2 h, and 80% HPAC, resulting in 92.7% delignification and 87.8% cellulose retention in the AC-pretreated poplar. The two step-treated poplar presented 86.6% glucose yield and 89.0% xylose yield by enzymatic hydrolysis with a cellulases loading of 7.2 m/g dry mass. Very high glucose (93.8%) and xylose (94.6%) yields were obtained with 14.3 mg cellulases/g dry mass. Both Tween 80 and β-glucosidase enhanced glucose yield of HPAC-pretreated poplar by alleviating the accumulation of cellobiose. Under the optimal conditions, 6.9 g XOS, 40.3 g glucose, and 8.9 g xylose were produced from 100 g poplar.


The AC and HPAC pretreatment of poplar represented an efficient strategy to produce XOS and fermentable sugars with high yields. This two-step pretreatment was a recyclable benign and advantageous scheme for biorefinery of the poplar into XOS and monosaccharides.


Cellulosic biomass represents a renewable, low-cost resource that can be converted into biofuels and biochemicals [1, 2]. Poplar, as a fast growing, widely distributed, short rotation period crop, is considered as a suitable feedstock for this process [3, 4]. Enzymatic hydrolysis of poplar for the production of fermentable sugars, a key step for biofuels and biochemicals production, has been extensively investigated and different pretreatments, including ionic liquids, steam explosion, and acid/alkaline media, have been adopted to increase the accessibility of enzymes to polysaccharides [5,6,7,8,9,10]. These pretreatments are usually conducted with high temperature or long time [6]. Moreover, severe pretreatment could easily solubilize cellulose and xylan in poplar and made them hard to be recovered and utilized [7, 8, 10]. Therefore, efficiently utilization of polysaccharides in poplar still remains a challenge.

Xylooligosaccharides (XOS), derived from xylan in lignocellulosic biomass by enzymatic and/or chemical hydrolysis, have important prebiotic properties and show great potential application in medicinal, food, and health fields [11]. Recently, co-production of functional xylooligosaccharides and fermentable sugars from lignocellulosic materials by autohydrolysis, alkaline, and acid pretreatments has been reported [11,12,13,14,15,16]. Acetic acid (AC) pretreatment offered a green approach to effectively convert corncobs, viscose fibers, and poplar to XOS and fermentable sugars [14,15,16]. It has been reported that a good XOS yield of 45.91% was obtained from corncob by AC pretreatment at pH 2.7 and 150 °C for 30 min [14]. AC-pretreated poplar can produce a 36.0% XOS yield with 6.5% AC at 172 °C for 27 min with a clear increase (from 28.3 to 51.0%) of hydrolysis yield of AC-pretreated poplar by cellulases compared to poplar after autohydrolysis [15]. Normally, AC can be used to remove lignin with high temperature and high AC concentration [17]. However, after 6.5% AC pretreatment at 170 °C, the AC-pretreated poplar had high lignin content (> 30%) [15]. A large amount of lignin in poplar is unfavorable for enzymatic hydrolysis [18]. Thus, it is necessary to probe an effective method to alleviate lignin inhibition or to remove lignin to increase cellulases accessibility to cellulose in AC-pretreated poplar.

In this work, XOS and monosaccharides were produced from poplar by a combination of AC and hydrogen-peroxide/acetic acid (HPAC) pretreatments and enzymatic hydrolysis. Effects of AC concentration, temperature, time on XOS yields were investigated. After that, the AC-pretreated solid residues were then subjected to the HPAC process to remove lignin, aiming at enhancing the hydrolyzability of cellulose in poplar. The effects of Tween 80 and β-glucosidase on the hydrolysis of HPAC-pretreated poplar were also probed.

Results and discussion

AC pretreatment

Component analysis of AC-pretreated poplar

In the pretreatment of poplar with water (autohydrolysis) for 10, 30, and 50 min, the xylan content decreased from 17.4% to 16.5%, 11.0%, and 8.4%, respectively (Table 1). When the AC concentration was less than 5%, very high glucan retention (> 93%) was observed and the contents of glucan and lignin increased due to the removal of xylan by AC pretreatment. The highest acid insoluble lignin content (36.1%) was obtained from the poplar pretreated with 5% AC for 50 min. With the presence of 10% AC at 170 °C for 10 min, xylan and lignin were solubilized and the xylan and lignin removal increased from 6.8% and 0.3% to 40.2% and 6.0%, respectively. The data indicated that AC pretreatment was more effective than autohydrolysis pretreatment in xylan and lignin removal [18]. After pretreatment with 10% AC at 170 °C for 50 min, the xylan content decreased to 3.2% with a xylan removal of 87.8% and a lignin removal of 11.9%.

Table 1 Chemical compositions of poplar after AC pretreatment at 170 °C, expressed as percentage of dry mass (DM)

Table 2 shows that 5% AC pretreatment for 30 min gave the highest XOS yield (55.8%), which was close to the yield of 51.5% (based on the xylan removed in pretreatment liquor) obtained in previous work [15]. However, the XOS yield from poplar was lower than that from corncob (62.2%, based on the xylan removed in pretreatment liquor) [14]. In this work, 5% AC and 30 min was chosen as the optimal AC conditions because it gave the highest XOS yield (55.8%) and acceptable loss of glucan (5.5%). After the optimal AC pretreatment, about 12.4 g xylan was removed in the pretreatment liquor from 100 g poplar and 6.9 g XOS and 4.6 g xylose were produced in the AC pretreatment liquor. The results indicated that some high DP oligomers were produced in AC pretreatment of poplar. The AC-pretreated poplar with optimal conditions contained 54.9 g glucan, 6.7 g xylan and 33.4 g lignin per 100 g of non-pretreated poplar, which corresponded to the removal of 71.3% of the original xylan and 4.9% of the original lignin (Table 1).

Table 2 The formations of xylose and XOS (DP 2–6) from poplar by the 0–10% AC pretreatment for 10–50 min

Characterization of AC-pretreated poplar

The XRD patterns of the non-pretreated and pretreated poplar samples showed that the crystalline structure of the cellulose in these poplar materials was unchanged after AC pretreatment and could be assigned as cellulose I (Additional file 1: Fig. S1) [19]. The crystallinity index (CI) indicates the relative amount of crystalline cellulose in the sample, and Table 3 demonstrated that the CI values of the poplar increased from 47.1% of raw poplar to 55.2% of AC-pretreated poplar (5% AC, 170 °C, 30 min). The AC pretreatment resulted in the increase in CI was due to the removal of xylan (Table 1). The removal of xylan can also be observed by FTIR spectroscopy (Additional file 1: Fig. S2). After the AC pretreatment, both the peak related to C=O groups associated with ester linkages between the lignin and hemicellulose at 1720 cm−1 and the peak due to the C–O–C stretching of the acetyl groups in hemicellulose at 1245 cm−1 decreased in intensity [20]. At the same time, the absorption bands at 1300–1600 cm−1 related to lignin increased in strength. The data here supported the selective removal of xylan by the AC pretreatment (Table 1).

Table 3 XPS, acetyl, hydrophobicity, and crystallinity index (%) analysis of non-pretreated and 5% AC-pretreated poplar

The surface chemistry of biomass can be investigated by XPS [21] and a high O/C reflects higher cellulose and/or hemicellulose content, while a low O/C suggests the presence of more lignin [22]. The surface proportions of C and O atoms in the non-pretreated and pretreated poplar are provided in Table 3. In AC-pretreated poplar samples, C1, C2, and C3 carbon peaks were observed (Additional file 1: Fig. S3), which were in good agreement with the results obtained from corn stover [23, 24]. With the increase in pretreatment time from 10 to 50 min, the O/C ratio of AC-pretreated poplar increased from 0.37 to 0.41 and C1 peak intensity reduced from 56.0 to 49.4%, which indicated that surface lignin content decreased after AC pretreatment. The O/C ratio of AC-pretreated poplar was lower than that of raw poplar, possibly because of the removal of the extracts [21]. The C1 peak intensity of 10 min AC-pretreated poplar (56.0%) was higher than non-pretreated poplar (54.0%). The increase in C1 peak intensity indicated the increased surface lignin content. This result could be due to the lignin redeposition on the surface of poplar during AC pretreatment [22].

Hydrophobic interactions are regarded as the main driving force for the formation of non-productive binding between lignocellulose and cellulases [25]. The hydrophobicity values of the raw and pretreated poplar are presented in Table 3 and Additional file 1: Fig. S4. The hydrophobicity of the raw poplar was 0.37 g/L. As the AC treatment time increased from 10 to 50 min, the hydrophobicity of the poplar reduced from 0.54 to 0.31 g/L. However, the hydrophobicity of 5% AC and 30 min pretreated poplar was 0.49 g/L, which was still higher than that of the raw poplar. Hydrophobicity has been often characterized as a critical contributory factor to lignin inhibition of enzymatic hydrolysis [26] and cellulases adsorption onto lignin in pretreated substrates by hydrophobic interactions has been confirmed [25]. The higher hydrophobicity of AC-pretreated poplar indicated that the AC-pretreated poplar exhibited stronger cellulases adsorption capacity than the non-pretreated poplar [22].

The surfaces images of the raw and AC-pretreated poplar were characterized by SEM (Additional file 1: Fig. S5). The AC pretreatment resulted in less damage to the rigid structure of the raw poplar. Compared with the non-pretreated poplar, a plethora of spherical droplets was observed on the surfaces of the 5% and 10% AC-pretreated samples. These observations were in agreement with prior reports that the lignin droplets can be found on substrate after dilute acid pretreatment [27,28,29,30]. Lignin droplets probably led to a low hydrolysis yield of AC-pretreated poplar because the lignin droplets formed by acid pretreatment strongly inhibited cellulose hydrolysis in biomass by steric hindrance and non-productive adsorption of enzymes [31, 32].

Enzymatic hydrolysis of AC-pretreated poplar

Only 11.4% of glucose yield and 8.8% of xylose yield were obtained from the non-pretreated poplar with a cellulases loading of 28.6 mg/g DM. After pretreatment with 0% AC (autohydrolysis) for 10 and 50 min, glucose yields were 9.9% and 17.3%, respectively (Fig. 1a). In the enzymatic hydrolysis of poplar pretreated by 10% AC for 50 min, glucose yield increased to 27.6% and xylose yield reached 43.1% (Fig. 1b). With the increase in cellulases dosage up to 85.8 mg protein of cellulases/g DM, the glucose and xylose yields in AC-pretreated poplar (5%, 170 °C, 30 min) were 29.1% and 40.3%, respectively (Additional file 1: Fig. S6). The results here confirmed that hydrolysis yields of poplar pretreated by AC under the tested conditions were limited, which could be partially due to acetylation and the presence of high lignin content (> 25%) in the pretreated poplar [18, 33].

Fig. 1

Enzymatic hydrolysis of AC pretreated poplar by cellulases. Glucose (a) and xylose (b) yield from AC (0–10% for 10–50 min) pretreated poplar by cellulases CTec2 (28.6 mg/g DM) at 50 °C and pH 5.0 for 48 h

The 5% AC-pretreated poplar had higher acetyl content (more than 5.5%) than raw poplar (Table 3). It has been pointed out that pretreatment of lignocellulosic biomass with AC may result in the acetylation of its compounds such as cellulose and hemicellulose [31]. Enzymatic hydrolysis of the AC-pretreated poplar without any additional alkali pretreatment may not break the acetylated glucan and xylan and subsequently, affect their conversion to sugars [33]. In order to explore the effect of acetyl contents in AC-pretreated poplar on enzymatic hydrolysis, 1% (w/v) sodium hydroxide was used to treat AC-pretreated poplar (5% AC, 170 °C, 30 min) at 120 °C for 1 h with a solid loading of 10% (w/v). After sodium hydroxide pretreatment, the glucose yield of poplar by cellulases increased from 20.0 to 35.2%, indicating the increase in hydrolysis yield by alkali pretreatment. A similar phenomenon has also been observed in the hydrolysis of deacylated corncob and wood [14, 31, 34, 35]. In this work, such a low glucose yield (35.2%) was noticed in the hydrolysis of deacylated AC-pretreated poplar, which indicated that the acetylation of poplar might be not responsible for the main reason of the low hydrolysis yield of AC-pretreated poplar. Thus, the high residual lignin contents (25.1–36.1%) in the AC-pretreated poplar might be responsible for the relatively low hydrolysis yield [36, 37].

HPAC pretreatment

Component analysis of HPAC-pretreated poplar

HPAC pretreatment is gaining more interest because of its highly effective removal of lignin [20, 38, 39]. In previous report, 98.08% of acid-insoluble lignin from pine wood was removed by 100% HPAC pretreatment at 80 °C for 2 h [38]. After 100% HPAC pretreatment at 80 °C for 3 h, about 90.3% lignin was removed and 86.0% enzymatic hydrolysis yield was obtained from Jerusalem artichoke [39]. It has been reported that 90.4% lignin removal and 84.0% glucose yield were observed from yellow poplar by HPAC pretreatment at 120 °C for 5 min [20]. In this work, after AC pretreatment, the poplar contained high lignin content (> 25%) and HPAC pretreatment was used for delignification of AC-pretreated poplar. With 40%, 60%, 80%, and 100% HPAC pretreatment of AC-pretreated poplar at 60 °C, the lignin content decreased from 33.4% to 22.4%, 15.3%, 4.3%, and 1.2%, respectively (Table 4). Pretreatment with 100% HPAC at 60 °C retained 90.9% glucan and removed 98.0% lignin and 23.5% xylan, indicating that HPAC pretreatment showed a powerful delignification capability. As the temperature increased from 40 to 80 °C, very high lignin removal (82.6–99.6%) was observed and the contents of glucan and xylan increased due to the removal of lignin by 100% HPAC pretreatment. Meanwhile, 2.5–13.0% glucan were lost as the HPAC pretreatment temperature increased from 40 to 80 °C (Table 4). The lowest lignin content (0.2%) in poplar was achieved with 100% HPAC at 80 °C for 2 h, which resulted in the highest glucan removal (13.0%). Our results indicated that HPAC pretreatment was highly effective for removing lignin from poplar, which was in good agreement with the results obtained from wood [38].

Table 4 Chemical compositions of HPAC-pretreated poplar, expressed as percentage of DM

Characterization of HPAC-pretreated poplar

After HPAC pretreatment (80% HPAC, 60 °C, 2 h), the CI value of the AC-pretreated poplar (5% AC, 170 °C, 30 min) increased from 55.2 to 64.2%. The HPAC pretreatments resulted in the increase in CI possibly because of the removal of lignin fractions (Tables 4, 5) [22]. Following the HPAC pretreatment, the FTIR absorption bands at 1300–1600 cm−1 related to lignin decreased (Additional file 1: Fig. S2). In addition, several absorption bands associated with glucan increased compared with those in the raw poplar spectrum. Specifically, the O–H stretch at 3330 cm−1 and the C–H stretch at 2900 cm−1 associated with glucan were stronger after the two-step pretreatment [20]. The results here indicated that HPAC pretreatment removed both xylan and lignin leaving a glucan-rich poplar (Table 5).

Table 5 XPS, acetyl, hydrophobicity, and crystallinity index (%) analysis of HPAC-pretreated poplar

It has been determined that in XPS analysis, the O/C ratios of different lignocellulose components decrease in the order of glucan > hemicellulose > lignin [21, 40]. After the HPAC pretreatment, the O/C ratio increased while the C1 peak intensity reduced (57.1–51.0%) as lignin was removed (Table 5). The O/C ratio (0.40) and C1 peak intensity (53.8%) of AC-pretreated poplar were very close to those of the HPAC-pretreated poplar. In addition, it was important to note that the content of acetyl group in the poplar increased when HPAC pretreatment became more severe (Table 5) possibly due to the formation of acetylated glucan and xylan during the pretreatment [33]. The acetylated glucan and xylan may change the O/C ratio of the substrates. Thus, the O/C ratio could not be used to evaluate the surface lignin content in HPAC-pretreated poplar. In addition, the hydrophobic acetate on the glucan surface could block the adsorption of cellulases [31].

The hydrophobicity of HPAC-pretreated poplar was lower than that of AC-pretreated poplar, and more severe HPAC pretreatment conditions reduced the hydrophobicity of the material (Table 5 and Additional file 1: Fig. S4). The main cause of this phenomenon was that the removal of lignin increased the relative contents of glucan in the remaining poplar. It has been reported that lignin is more hydrophobic than glucan, as hydrophobicity decrease as the O/C ratio increases [24]. Obviously, the removal of xylan and lignin had a pronounced effect on the hydrophobicity of the poplar and might affect hydrolysis yield of the pretreated poplar (Fig. 2).

Fig. 2

Glucose (a) and xylose (b) yields from 2% HPAC-pretreated poplar by CTec2 (28.6 mg/g DM) at 50 °C and pH 5.0 for 72 h. The HPAC pretreatment of poplar was based on the poplar pretreated with 5% AC at 170 °C for 30 min

Compared with the AC-pretreated material, the poplar after HPAC pretreatments showed more serious surface damage in the SEM photo (Additional file 1: Fig. S5). In addition, the lignin drops formerly seen on the AC-pretreated poplar disappeared after the HPAC treatment. Similar to pseudo-lignin, the re-deposited lignin droplets on the biomass surface were observed to have detrimental impacts on the enzymatic hydrolysis [27] and the removal of lignin droplets by HPAC might be helpful for enzymatic hydrolysis of AC-pretreated poplar.

Enzymatic hydrolysis of HPAC-pretreated poplar

After 40–100% HPAC pretreatment of the AC-pretreated poplar at 60 °C, the glucose yield enhanced from 20.0% to 41.7–79.2% (Fig. 2a), which could be due to the removal of lignin by HPAC and the increase in cellulases accessibility to cellulose [38]. When the pretreatment temperature increased from 40 to 80 °C, the glucose yield of 100% HPAC pretreated poplar increased from 46.3 to 76.5%. Meanwhile, 52.0–98.9% xylose yields were obtained from the HPAC-pretreated poplar (Fig. 2b). Such improved saccharification of HPAC-pretreated poplar could be attributed to the relatively high lignin removal (49.2% to 99.6%) during the pretreatment process (Table 4).

The observed 67.2% glucose and 72.4% xylose yields were unexpectedly low in light of the high degree of delignification (92.7%) which was achieved by 80% HPAC pretreatment at 60 °C for 2 h (Fig. 2a, Table 4). Only 76.5% glucose and 95.6% xylose yields were obtained from poplar with 99.6% lignin removal by HPAC pretreatment (100% HPAC, 80 °C for 2 h) (Fig. 2). A similar phenomenon has also been reported that the use of HPAC-pretreated poplar led to an unexpectedly enzymatic conversion (less than 80%) at a very low lignin content of 2.0% [41]. This phenomenon might due to the grafting of hydrophobic acetate on the cellulose surface blocked the adsorption of cellulases, thereby reducing the hydrolysis yield [31]. In order to explore the effect of acetyl content in HPAC-pretreated poplar on enzymatic hydrolysis, 0.1% (w/v) sodium hydroxide was used to treat HPAC-pretreated poplar (80% HPAC, 60 °C, 2 h) at 50 °C for 1 h with a solid loading of 10% (w/v) [35]. After sodium hydroxide treatment, the glucose yield of poplar increased from 67.2 to 74.4%. The data indicated that the acetylation might be one of reason to hinder the enzymatic hydrolysis of HPAC-pretreated poplar.

Interestingly, 2.7 mg/mL cellobiose was produced in the enzymatic hydrolysis of the HPAC-pretreated (80% HPAC, 60 °C, 2 h) poplar, which can strongly inhibit the action of cellobiohydrolase I and reduce enzymatic hydrolysis yield [42]. Supplementation of CTec2 cellulases with 11.1 mg protein of β-glucosidase per g DM improved the glucose and xylose yields from 67.2% and 72.4% to 94.0% and 97.0%, respectively (Fig. 3a).

Fig. 3

Effects of Tween 80 and β-glucosidase on the hydrolysis of 2% HPAC-pretreated poplar (80% HPAC, 60 °C) CTec2 (28.6 mg/g DM) at 50 °C and pH 5.0 for 72 h. a Effect of β-glucosidase (11.1 mg/g DM) on glucose and xylose yields. b Effect of Tween 80 (0.5–1.5 mg/mL) on glucose yield. c Effect of Tween 80 (0.5–1.5 mg/mL) on xylose yield. d Effect of Tween 80 (1.0 mg/mL) and β-glucosidase (11.1 mg/g DM) on the hydrolysis with different CTec2 loading

Meanwhile, 0.05–0.24 mg/mL XOS (DP 2–6) were found in the enzymatic hydrolyte of HPAC-pretreated poplar. The inhibition of XOS to cellulases could also affect the hydrolysis yield of the HPAC-pretreated poplar [43]. Similar phenomenon has been reported that adding extra β-glucosidase with CTec2 improved the glucose and xylose yields of glycerol treated Miscanthus straw from 12.5% and 4.2% to 88.8% and 68.5%, respectively [44]. In this work, relatively high content of cellobiose in the hydrolysate of HPAC-pretreated poplar could inhibit the hydrolytic capacity of xylanase in CTec2 and decreased the xylose yield [45].

It has been reported that the use of surfactants in enzymatic hydrolysis can reduce the non-productive binding between lignin and cellulases and improve the enzymatic hydrolysis yield [46, 47]. 97.4% Glucose and 98.6% xylose yields were obtained from the HPAC-pretreated poplar after supplementation of 1 mg/mL Tween 80 with 28.6 mg protein of cellulases/g DM (Fig. 3b, c). After addition of Tween 80, the HPAC-pretreated poplar presented a remarkable hydrolysis yields of glucose (86.6%) and xylose (89.0%) with a cellulases loading of 7.2 mg/g DM (Fig. 3d), which could be explained by that Tween 80 increased the activity or stability of β-glucosidase and consequently alleviated the accumulation of cellobiose. Additionally, very high glucose (93.8%) and xylose (94.6%) yields also were obtained 14.3 mg protein of cellulases/g DM. Thus, employing Tween 80 instead of β-glucosidase was a viable mean to improve the hydrolysis yield. In this work, compared with previous reports on poplar 86.6% glucose yield with a cellulases loading (7.2 mg protein/g DM) or 93.8% glucose yield with 7.2 mg protein of cellulases/g DM and 1 mg/mL Tween 80 achieved satisfactory results [6, 7, 9, 15]. It has been reported that acetyl groups might inhibit the enzymes by interfering with the productive binding between cellulose and the catalytic domain of cellulases [31]. However, Tween 80 can change the ultrastructure of the substrate, making the cellulose more available to enzymatic attack and increase enzyme stability by reducing thermal denaturation or denaturation by shear forces [46]. Hence, this might be the reason that the Tween 80 increased enzymatic hydrolysis yield of the HPAC-pretreated poplar.

Comparison of different pretreatment methods of poplar

This work proposed a two-step pretreatment for the efficient production of XOS and fermented sugars from poplar and 6.9 g XOS, 40.3 g glucose and 8.9 g xylose could be produced from 100 g of poplar (Fig. 4). The AC and HPAC pretreated poplar presented remarkable hydrolysis yields of 86.6% glucose and 89.0% xylose at a cellulases loading of 7.2 mg/g DM and very high glucose (93.8%) and xylose (94.6%) yields were obtained with 14.3 mg protein of cellulases/g DM. The AC pretreatment and HPAC pretreatment were milder and more efficient than those associated with various typical poplar pretreatments (Table 6). Single step pretreatments such as steam explosion and those using alkaline peroxide or ionic liquids all require high temperatures and long treatment times and exhibit low enzymatic hydrolysis rates and poor conversion of certain components [6,7,8, 48, 49]. For example, only 60% enzymatic hydrolysis yield was obtained from poplar by a high temperature (210 °C) steam explosion pretreatment [7]. In the sulfuric acid and steam explosion pretreatments, the first step poplar pretreatment condition was 0.7% H2SO4 at room temperature overnight and the second step pretreatment condition was steam explosion at 190 °C for 10 min and finally only 70% glucose yield was obtained by 72 h enzymatic hydrolysis with loading 32 mg cellulases/g DM [9]. Additionally, two-step poplar pretreatments such as sodium hydroxide and sodium sulfate, white-rot and sodium hydroxide, sulfuric acid and steam explosion, sulfur dioxide steam explosion and ethanol can improve poplar hydrolysis yield, but the associated conditions are still very severe [5, 9, 10]. In this work, xylan in poplar was efficiently used for XOS production and glucan was almost completely hydrolysis. After AC pretreatment, the AC concentration in pretreatment liquor (5.2 mg/mL AC, 170 °C, 30 min) was 4.7 mg/mL (Additional file 1: Table S1). AC in the pretreatment liquor can be recycled by liquid–liquid extraction [50]. During the HPAC pretreatment, the AC was consumed and peroxyacetic acid was formed. Pressure shift distillation coupled with a separation process was capable to separate AC and peroxyacetic acid in HPAC pretreatment liquor [51, 52]. The two-step pretreatment of AC and HPAC provided a preferable feature to prepare XOS and monosaccharides from poplar with relatively mild conditions, showing great potential application in industrial production of XOS, biofuels, and biochemicals from biomass.

Fig. 4

The overall mass balance for production of XOS and monosaccharides from poplar by a two-step AC and HPAC pretreatment

Table 6 The enzyme hydrolysis of pretreated poplar by different methods


The AC pretreatment of poplar solubilized the most xylan in poplar and gave rise to a 55.8% XOS yield. The HPAC pretreatment presented 49.2–99.6% lignin removal of AC-pretreated poplar and improved the glucose yield from 20.0% to above 90% with a dosage of 14.3 mg protein of cellulases/g DM and 11.1 mg protein of β-glucosidase/g DM or 1 mg/mL Tween 80. The two-step pretreatment offered an approach to effectively converting 100 g poplar to 6.9 g XOS and 49.2 g monosaccharides. The AC and HPAC two-step pretreatment of poplar for producing XOS and fermentable sugars could facilitate means to develop an economically viable biorefinery process.



Poplar used in this work was kindly supplied by Prof. Yong Xu from Nanjing Forestry University. The material was air dried for 3 days, followed by pulverization to obtain a powder with an 80 mesh particle size (≤ 0.178 mm), having a moisture content of 9.40%. The contents of glucan, xylan, acid insoluble lignin and acid soluble lignin in the raw poplar were 43.38%, 17.36%, 24.43%, and 3.50%, respectively, determined using a method published by the National Renewable Energy Laboratory [53].

Cellic CTec2 (Novozymes A/S, Bagsværd, Denmark) had an activity of 123.0 filter paper units (FPU)/mL (176.2 mg protein/mL) determined according to the International Union of Pure and Applied Chemistry standard assay [54]. The Novozyme 188 (β-glucosidase) was determined to be 8451 nkat/mL (187.9 mg protein/mL) as described previously [55]. The enzyme protein was quantified by the Lowry method using bovine serum albumin (Sigma-Aldrich, St. Louis, MO, USA) as the standard [56]. Xylobiose, xylotriose, xylotetraose, xylopentaose, and xylohexaose were purchased from Megazyme (Wicklow, Ireland).

AC pretreatment

The AC pretreatment was performed in a sealed, Teflon-lined stainless steel autoclave (HT-100H-316L, Anhui Kemi Machinery Technology Co., Ltd., Anhui, China) heated in a Constant Temperature Oil Bath (HH-SB, Jinhua Wenhua Equipment and Instrument Co., Ltd., Zhejiang, China). The AC pretreatment conditions were referred to a previous report [15]. The system was heated about 30 min from 25 to 170 °C (5 °C/min). AC concentrations of 0%, 5% (5.2 mg/mL), or 10% (v/v) (10.5 mg/mL) were used to treat poplar samples with a solid loading of 10% (w/v). The process was performed at 170 °C for 10, 30 or 50 min. Each experiment was carried out in triplicate. Following the reaction, the sealed tank was taken out from oil bath and immediately cooled down to room temperature with tap water in 30 min. The pretreatment liquor was separated from the slurry through vacuum filtration. Part of pretreatment liquor was used to determine the XOS concentration. The solid was recovered by filtration and washed repeatedly with distilled water until the wash water had a neutral pH, then stored at − 20 °C for chemical composition analysis and enzymatic hydrolysis.

HPAC pretreatment

A sample of poplar pretreated by 5% AC at 170 °C for 30 min was employed for the subsequent HPAC pretreatment. The HPAC solution was prepared by mixing hydrogen peroxide (30%, w/w) and acetic acid (99%, w/w) at a ratio of 1:1 (v/v) [38]. To investigate the effects of temperature on HPAC pretreatment, AC-pretreated poplar were pretreated with 100% (v/v) HPAC at temperatures of 40 °C, 60 °C, and 80 °C. The effect of HPAC concentration (40–100%, v/v) on pretreatment was investigated at 60 °C. All pretreatments were preformed for 2 h at a solid to liquid ratio of 1:10 (w/v) with 100 mM H2SO4 as a catalyst. The solid residues were separated by filtration and washed extensively with distilled water until the wash water had a neutral pH, then stored at − 20 °C for chemical composition analysis and enzymatic hydrolysis.

Enzymatic hydrolysis

Hydrolysis of the raw and treated poplar was performed in test tubes (601051-1, Biosharp, Hefei, China) with a 3 mL working volume in a 50 mM sodium citrate buffer (pH 5.0) at 50 °C and 200 rpm [53]. NaN3 (0.02% w/v) was added to the hydrolysis broth to prevent bacterial growth. The AC-pretreated poplar loading in each reaction mixture was 2% (w/v), with a cellulases loading of 14.3, 28.6, 43.0, 57.3, 71.3, 85.8 mg protein (10, 20, 30, 40, 50, 60 FPU)/g DM. The cellulases loading in hydrolysis of HPAC-pretreated poplar was 7.2, 14.3, 21.5, 28.6 mg protein (5, 10, 15, 20 FPU)/g DM. The β-glucosidase loading was 500 nakt (11.1 mg protein)/g DM for hydrolysis of HPAC-pretreated poplar. The concentration of Tween 80 in hydrolysate was 0.5–1.5 mg/mL. Two tubes of replicate test were withdrawn at intervals ranging from 12 to 72 h and boiled for 10 min to stop the enzymatic hydrolysis. Enzymatic hydrolysate was boiled for 10 min to stop the enzymatic hydrolysis. After cooling, the samples were separated by centrifugation (10,000×g, 10 min) and the cellobiose, XOS, glucose, and xylose in the supernatants were analyzed. Two replicate tests were performed for all hydrolysis experiments and average values are presented.

Characterization of solid residues

The crystallinity index (CI) of each raw and treated poplar specimen was determined by XRD using a Rigaku D/max-3 C instrument (Rigaku Corporation, Japan) [19]. The CI was determined using the equation:

$${\text{CI\% }} = \frac{{I_{002} - I_{\text{am}} }}{{I_{002} }} \times 100{\text{\% }}$$

where I002 is the maximum intensity of the diffraction at approximately 22.5° that corresponds to crystalline regions and Iam is the minimum intensity of the peak at approximately 18.0° that corresponds to amorphous regions.

Chemical functional groups were characterized using a Nicolet iS10 FTIR spectrophotometer (Thermo Fisher, USA), acquiring spectra over the range of 4000–400 cm−1 and adding 32 scans to generate each spectrum. The background spectrum of the diamond window without a sample was subtracted from each sample spectrum.

XPS analyses were performed based on the method reported by Kumar and Montplaisi to determine the atomic compositions and chemical environments of the poplar sample surfaces [24, 57]. The hydrophobicities of the poplar samples were determined via the method previously described [58, 59].

The surface morphologies of the raw and pretreated poplar specimens were observed by SEM (JSM 6360LV, Jeol, Japan) with an acceleration voltage of 10 kV. The samples were coated with gold to make them conductive before imaging and images were acquired at 1000, 2000 and 5000× magnification.

Analytical methods

The acetyl contents of poplar solids were determined as per NREL LAP002 using glacial acetic acid as a calibration standard [53].

The calculation of XOS (DP 2-6) yields was based on the removed xylan in the pretreatment liquor. Total oligosaccharide contents of the AC pretreatment liquors were determined indirectly after quantitative acid hydrolysis with 4% H2SO4 at 121 °C for 1 h, according to NREL/TP-510-42623. XOS (DP 2-6) was analyzed using high performance anion exchange chromatography coupled with pulsed amperometric detection (Dionex ICS-5000). The analysis employed 0.1 M NaOH and 0.5 M NaOAc containing 0.1 M NaOH as the mobile phases, at a flow rate of 0.3 mL/min in conjunction with a CarboPac PA200 anion exchange column [60].

Acetic acid, cellobiose, and monosaccharides were analyzed by high-performance liquid chromatography (Agilent 1260), using an Aminex Bio-Rad HPX-87H column and a refractive index detector together with 5 mM H2SO4 as the mobile phase at a flow rate of 0.5 mL/min. All samples were diluted with Milli-Q water prior to analysis. Two replicate assays were performed for each sample, and average values are presented.


The pretreatment severity factor was used to monitor and compare the pretreatment severity [24, 61].

$${\text{Severity}}\;\;{\text{factor}} = \log \left[ {t\; *\;\exp \left( {\frac{{T_{\text{i}} - T}}{14.75}} \right)} \right]$$

where t refers to pretreatment time (min), Ti is the reaction temperature (°C), and T is the reference temperature of 100 °C.

The percent recovery and percent removal of each component were calculated by the following formula [62]:

$${\text{Soild recovery }}\left( {\text{\%}} \right) = \frac{{W_{{{\text{after}}\;{\text{pretreatment}}}} }}{{W_{\text{before pretreatment}} }} \times 100$$

where Wbefore pretreatment and Wafter pretreatment were the weight of poplar before and after pretreatment.

$${\text{Removal }}\left( {\text{\%}} \right) = 1 - \frac{{W_{\text{component after pretreatment}} }}{{W_{\text{component before pretreatment}} }} \times 100$$

where Wcomponent before pretreatment and Wcomponent after pretreatment were the weight of the components (cellulose, xylan and, lignin) in poplar before and after pretreatment (g).

The xylose and XOS (DP 2 to 6) yields from AC pretreatment liquor were calculated based on the following equations [16, 63]:

$${\text{Xylose yield}}_{\text{AC pretreatment liquor }} \left( {\text{\%}} \right) = \frac{{ {\text{Xylose in AC pretreatment liquor }}\left( {\text{g}} \right) \times 0.88}}{{{\text{Removed xylan in AC pretreatment liquor }}\left( {\text{g}} \right)}} \times 100$$
$${\text{XOS yield }}_{\text{AC pretreatment liquor }} \left( {\text{\%}} \right) = \frac{{ {\text{XOS }}\left( {{\text{DP }}2 - 6} \right) {\text{in AC pretreatment liquor }}\left( {\text{g}} \right)}}{{{\text{Removed xylan in AC pretreatment liquor }}\left( {\text{g}} \right)}} \times 100$$

The yields of glucose, xylose, cellobiose, and XOS (DP 2 to 6) were calculated based on the following equations [16]:

$${\text{Glucose yield }}\left( {\text{\%}} \right) = \frac{{{\text{Glucose in enzymatic hydrolysate}} \times 0.9}}{\text{Theoretical amount of glucan in pretreated poplar}} \times 100$$
$${\text{Cellobiose yield }}\left( {\text{\%}} \right) = \frac{{{\text{Cellobiose in enzymatic hydrolysate}} \times 0.9}}{\text{Theoretical amount of glucan in pretreated poplar}} \times 100$$
$${\text{Xylose yield }}\left( {\text{\%}} \right) = \frac{{{\text{Xylose in enzymatic hydrolysate}} \times 0.88}}{\text{Theoretical amount of glucan in pretreated poplar}} \times 100$$
$${\text{XOS yield}}\;\left( {\text{\%}} \right) = \frac{{{\text{XOS}}\left( {{\text{DP }}2 - 6} \right) {\text{in enzymatic hydrolysate}}}}{\text{Theoretical amount of xylan in pretreated poplar}} \times 100$$



acetic acid


hydrogen peroxide–acetic acid




dry mass


Fourier transform-infrared


scanning electron microscopy


X-ray diffraction


X-ray photoelectron spectroscopy


filter paper unit


  1. 1.

    Satari B, Karimi K, Kumar R. Cellulose solvent-based pretreatment for enhanced second-generation biofuel production: a review. Sustain Energy Fuels. 2019;3:11–62.

    CAS  Article  Google Scholar 

  2. 2.

    Wyman CE, Cai CM, Kumar R. Bioethanol from lignocellulosic biomass. In: Kaltschmitt M, editor. Energy from organic materials (Biomass): a volume in the encyclopedia of sustainability science and technology. 2nd ed. New York: Springer New York; 2019. p. 997–1022.

    Google Scholar 

  3. 3.

    Sannigrahi P, Ragauskas AJ, Tuskan GA. Poplar as a feedstock for biofuels: a review of compositional characteristics. Biofuel Bioprod Biorefin. 2010;4(2):209–26.

    CAS  Article  Google Scholar 

  4. 4.

    Devappa RK, Rakshit SK, Dekker RF. Forest biorefinery: potential of poplar phytochemicals as value-added co-products. Biotechnol Adv. 2015;33(6):681–716.

    CAS  PubMed  Article  Google Scholar 

  5. 5.

    Jiang H, Han B, Ge J. Enhancement in the enzymatic digestibility of hybrid poplar with poor residual hemicelluloses after Na2SO3 pretreatment. Bioresour Technol. 2015;180:338–44.

    CAS  PubMed  Article  Google Scholar 

  6. 6.

    Kim KH, Dutta T, Ralph J, Mansfield SD, Simmons BA, Singh S. Impact of lignin polymer backbone esters on ionic liquid pretreatment of poplar. Biotechnol Biofuels. 2017;10:101.

    PubMed  PubMed Central  Article  CAS  Google Scholar 

  7. 7.

    Negro MJ, Manzanares P, Ballesteros I, Oliva JM, Cabañas A, Ballesteros M. Hydrothermal pretreatment conditions to enhance ethanol production from poplar biomass. Appl Biochem Biotechnol. 2003;105(1–3):87–100.

    PubMed  Article  Google Scholar 

  8. 8.

    Zhang L, You T, Zhang L, Yang H, Xu F. Enhanced fermentability of poplar by combination of alkaline peroxide pretreatment and semi-simultaneous saccharification and fermentation. Bioresour Technol. 2014;164:292–8.

    CAS  PubMed  Article  Google Scholar 

  9. 9.

    Tian D, Chandra RP, Lee JS, Lu C, Saddler JN. A comparison of various lignin-extraction methods to enhance the accessibility and ease of enzymatic hydrolysis of the cellulosic component of steam-pretreated poplar. Biotechnol Biofuels. 2017;10:157.

    PubMed  PubMed Central  Article  CAS  Google Scholar 

  10. 10.

    Panagiotopoulos IA, Chandra RP, Saddler JN. A two-stage pretreatment approach to maximise sugar yield and enhance reactive lignin recovery from poplar wood chips. Bioresour Technol. 2013;130(1):570–7.

    CAS  PubMed  Article  Google Scholar 

  11. 11.

    Qing Q, Li H, Kumar R, Wyman CE. Xylooligosaccharides production, quantification, and characterization in context of lignocellulosic biomass pretreatment. In: Aqueous pretreatment of plant biomass for biological and chemical conversion to fuels and chemicals. 2013. p. 391–415.

    Google Scholar 

  12. 12.

    Zhang H, Zhou X, Xu Y, Yu S. Production of xylooligosaccharides from waste xylan, obtained from viscose fiber processing, by selective hydrolysis using concentrated acetic acid. J Wood Chem Technol. 2017;37(1):1–9.

    Article  CAS  Google Scholar 

  13. 13.

    Boonchuay P, Techapun C, Leksawasdi N, Seesuriyachan P, Hanmoungjai P, Watanabe M, Takenaka S, Chaiyaso T. An integrated process for xylooligosaccharide and bioethanol production from corncob. Bioresour Technol. 2018;256:399–407.

    CAS  PubMed  Article  Google Scholar 

  14. 14.

    Zhang H, Xu Y, Yu S. Co-production of functional xylooligosaccharides and fermentable sugars from corncob with effective acetic acid prehydrolysis. Bioresour Technol. 2017;234:343–9.

    CAS  PubMed  Article  Google Scholar 

  15. 15.

    Huang K, Luo J, Cao R, Su Y, Xu Y. Enhanced xylooligosaccharides yields and enzymatic hydrolyzability of cellulose using acetic acid catalysis of poplar sawdust. J Wood Chem Technol. 2018;38(5):371–84.

    CAS  Article  Google Scholar 

  16. 16.

    Huang C, Jeuck B, Du J, Yong Q, Chang H, Jameel H, Phillips R. Novel process for the coproduction of xylo-oligosaccharides, fermentable sugars, and lignosulfonates from hardwood. Bioresour Technol. 2016;219:600–7.

    CAS  PubMed  Article  Google Scholar 

  17. 17.

    Zhang K, Pei Z, Wang D. Organic solvent pretreatment of lignocellulosic biomass for biofuels and biochemicals: a review. Bioresour Technol. 2016;199:21–33.

    CAS  PubMed  Article  Google Scholar 

  18. 18.

    Demartini JD, Pattathil S, Miller JS, Li H, Hahn MG, Wyman CE. Investigating plant cell wall components that affect biomass recalcitrance in poplar and switchgrass. Energy Environ Sci. 2013;6(3):898–909.

    CAS  Article  Google Scholar 

  19. 19.

    Segal L, Creely JJ, Martin AE Jr, Conrad CM. An empirical method for estimating the degree of crystallinity of native cellulose using the X-Ray diffractometer. Text Res J. 1959;29(10):786–94.

    CAS  Article  Google Scholar 

  20. 20.

    Lee HR, Kazlauskas RJ, Park TH. One-step pretreatment of yellow poplar biomass using peracetic acid to enhance enzymatic digestibility. Sci Rep. 2017;7(1):12216.

    PubMed  PubMed Central  Article  CAS  Google Scholar 

  21. 21.

    Gustafsson J, Ciovica L, Peltonen J. The ultrastructure of spruce kraft pulps studied by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). Polymer. 2003;44(3):661–70.

    CAS  Article  Google Scholar 

  22. 22.

    Yang M, Wang J, Hou X, Wu J, Fan X, Jiang F, Tao P, Wang F, Peng P, Yang F, Zhang J. Exploring surface characterization and electrostatic property of Hybrid Pennisetum during alkaline sulfite pretreatment for enhanced enzymatic hydrolysability. Bioresour Technol. 2017;244(1):1166.

    CAS  PubMed  Article  Google Scholar 

  23. 23.

    Chen H, Liu L. Unpolluted fractionation of wheat straw by steam explosion and ethanol extraction. Bioresour Technol. 2007;98(3):666–76.

    Article  CAS  Google Scholar 

  24. 24.

    Kumar R, Mago G, Balan V, Wyman CE. Physical and chemical characterizations of corn stover and poplar solids resulting from leading pretreatment technologies. Bioresour Technol. 2009;100(17):3948–62.

    CAS  PubMed  Article  Google Scholar 

  25. 25.

    Nakagame S, Chandra RP, Kadla JF, Saddler JN. The isolation, characterization and effect of lignin isolated from steam pretreated Douglas-fir on the enzymatic hydrolysis of cellulose. Bioresour Technol. 2011;102(6):4507–17.

    CAS  PubMed  Article  Google Scholar 

  26. 26.

    Huang Y, Sun S, Huang C, Yong Q, Elder T, Tu M. Stimulation and inhibition of enzymatic hydrolysis by organosolv lignins as determined by zeta potential and hydrophobicity. Biotechnol Biofuels. 2017;1:10.

    Google Scholar 

  27. 27.

    Donohoe BS, Decker SR, Tucker MP, Himmel ME, Vinzant TB. Visualizing lignin coalescence and migration through maize cell walls following thermochemical pretreatment. Biotechnol Bioeng. 2008;101(5):913–25.

    CAS  PubMed  Article  Google Scholar 

  28. 28.

    Shinde SD, Meng X, Kumar R, Ragauskas AJ. Recent advances in understanding the pseudo-lignin formation in a lignocellulosic biorefinery. Green Chem. 2018;20:2192–205.

    CAS  Article  Google Scholar 

  29. 29.

    Li H, Pu Y, Kumar R, Ragauskas AJ, Wyman CE. Investigation of lignin deposition on cellulose during hydrothermal pretreatment, its effect on cellulose hydrolysis, and underlying mechanisms. Biotechnol Bioeng. 2014;111:485–92.

    CAS  PubMed  Article  Google Scholar 

  30. 30.

    Kumar R, Hu F, Sannigrahi P, Jung S, Ragauskas AJ, Wyman CE. Carbohydrate derived-pseudo-lignin can retard cellulose biological conversion. Biotechnol Bioeng. 2013;110:737–53.

    CAS  PubMed  Article  Google Scholar 

  31. 31.

    Pan X. Effect of acetyl groups on enzymatic hydrolysis of cellulosic substrates. Holzforschung. 2006;60(4):398–401.

    CAS  Article  Google Scholar 

  32. 32.

    Pu Y, Fan H, Fang H, Davison BH, Ragauskas AJ. Assessing the molecular structure basis for biomass recalcitrance during dilute acid and hydrothermal pretreatments. Biotechnol Biofuels. 2013;6:15.

    CAS  PubMed  PubMed Central  Article  Google Scholar 

  33. 33.

    Schneider L, Dong Y, Haverinen J, Jaakkola M, Lassi U. Efficiency of acetic acid and formic acid as a catalyst in catalytical and mechanocatalytical pretreatment of barley straw. Biomass Bioenergy. 2016;91:134–42.

    CAS  Article  Google Scholar 

  34. 34.

    Shuai L, Amiri MT, Questell-Santiago YM, Héroguel F, Li Y, Kim H, Meilan R, Chapple C, Ralph J, Luterbacher JS. Formaldehyde stabilization facilitates lignin monomer production during biomass depolymerization. Science. 2016;354:329.

    CAS  PubMed  Article  Google Scholar 

  35. 35.

    Shuai L, Questell-Santiago YM, Luterbacher JS. A mild biomass pretreatment using gamma-valerolactone for concentrated sugar production. Green Chem. 2016;18:937–43.

    CAS  Article  Google Scholar 

  36. 36.

    Mouthier T, Appeldoorn MM, Pel H, Schols HA, Gruppen H, Kabel MA. Corn stover lignin is modified differently by acetic acid compared to sulfuric acid. Ind Crop Prod. 2018;121:160–8.

    CAS  Article  Google Scholar 

  37. 37.

    Lai C, Yang B, He J, Huang C, Li X, Song X, Yong Q. Enhanced enzymatic digestibility of mixed wood sawdust by lignin modification with naphthol derivatives during dilute acid pretreatment. Bioresour Technol. 2018;269:18–24.

    CAS  PubMed  Article  Google Scholar 

  38. 38.

    Wi S, Cho E, Lee D, Lee S, Lee Y, Bae H. Lignocellulose conversion for biofuel: a new pretreatment greatly improves downstream biocatalytic hydrolysis of various lignocellulosic materials. Biotechnol Biofuels. 2015;8:228.

    PubMed  PubMed Central  Article  CAS  Google Scholar 

  39. 39.

    Song Y, Wi SG, Kim HM, Bae H-J. Cellulosic bioethanol production from Jerusalem artichoke (Helianthus tuberosus L.) using hydrogen peroxide-acetic acid (HPAC) pretreatment. Bioresour Technol. 2016;214:30–6.

    CAS  PubMed  Article  Google Scholar 

  40. 40.

    Chundawat SP, Venkatesh B, Dale BE. Effect of particle size based separation of milled corn stover on AFEX pretreatment and enzymatic digestibility. Biotechnol Bioeng. 2007;96(2):219–31.

    CAS  PubMed  Article  Google Scholar 

  41. 41.

    Luo M, Tian D, Shen F, Hu J, Zhang Y, Yang G, Zeng Y, Deng S, Hu Y. A comparative investigation of H2O2-involved pretreatments on lignocellulosic biomass for enzymatic hydrolysis. Biomass Convers Biorefin. 2018.

    Article  Google Scholar 

  42. 42.

    Andrić P, Meyer A, Jensen P, Dam-Johansen K. Reactor design for minimizing product inhibition during enzymatic lignocelluloses hydrolysis: I. Significance and mechanism of cellobiose and glucose inhibition on cellulolytic enzymes. Biotechnol Adv. 2010;28(3):308–24.

    PubMed  Article  CAS  Google Scholar 

  43. 43.

    Kumar R, Wyman CE. Strong cellulase inhibition by mannan polysaccharides in cellulose conversion to sugars. Biotechnol Bioeng. 2014;111:1341–53.

    CAS  PubMed  Article  Google Scholar 

  44. 44.

    Dąbkowska K, Alvarado-Morales M, Kuglarz M, Angelidaki I. Miscanthus straw as substrate for biosuccinic acid production: focusing on pretreatment and downstream processing. Bioresour Technol. 2019;278:82–91.

    PubMed  Article  CAS  Google Scholar 

  45. 45.

    Chen X, Xin D, Wang R, Qin Y, Wen P, Hou X, Zhang J. Factors affecting hydrolytic action of xylanase during pennisetum saccharification: role of cellulose and its derivatives. Ind Crop Prod. 2019;130:49–56.

    CAS  Article  Google Scholar 

  46. 46.

    Yang M, Zhang A, Liu B, Li W, Xing J. Improvement of cellulose conversion caused by the protection of Tween-80 on the adsorbed cellulase. Biochem Eng J. 2011;56(3):125–9.

    CAS  Article  Google Scholar 

  47. 47.

    Kumar R, Wyman CE. Effect of additives on the digestibility of corn stover solids following pretreatment by leading technologies. Biotechnol Bioeng. 2009;102:1544–57.

    CAS  PubMed  Article  Google Scholar 

  48. 48.

    Sun Q, Foston M, Meng X, Sawada D, Pingali S, O’Neill H, Li H, Wyman C, Langan P, Ragauskas A, Kumar R. Effect of lignin content on changes occurring in poplar cellulose ultrastructure during dilute acid pretreatment. Biotechnol Biofuels. 2014;7:150.

    PubMed  PubMed Central  Article  CAS  Google Scholar 

  49. 49.

    Bhagia S, Kumar R, Wyman CE. Effects of dilute acid and flowthrough pretreatments and BSA supplementation on enzymatic deconstruction of poplar by cellulase and xylanase. Carbohydr Polym. 2017;157:1940–8.

    CAS  PubMed  Article  Google Scholar 

  50. 50.

    Muurinen EI, Sohlo JJK. Simulation of recovery methods for pulping with peroxyformic and peroxyacetic acids. Comput Chem Eng. 1994;18:S609–13.

    Article  Google Scholar 

  51. 51.

    Zhao X, Wu R, Liu D. Production of pulp, ethanol and lignin from sugarcane bagasse by alkali-peracetic acid delignification. Biomass Bioenergy. 2011;35:2874–82.

    CAS  Article  Google Scholar 

  52. 52.

    Abdulrahman A, van Walsum GP, Um BH. Acetic acid removal from pre-pulping wood extract with recovery and recycling of extraction solvents. Appl Biochem Biotechnol. 2019;187(1):378–95.

    CAS  PubMed  Article  Google Scholar 

  53. 53.

    Sluiter A, Hames B, Ruiz R, Scarlata C, Sluiter J, Templeton D, Crocker D. Determination of structural carbohydrates and lignin in biomass. Golden: National Renewable Energy Laboratory; 2008.

    Google Scholar 

  54. 54.

    Ghose TK. Measurement of cellulase activities. Pure Appl Chem. 1987;59:257–68.

    CAS  Article  Google Scholar 

  55. 55.

    Bailey MJ, Nevalainen KMH. Induction, isolation and testing of stable Trichoderma reesei mutants with improved production of solubilizing cellulase. Enzyme Microb Technol. 1981;3(2):153–7.

    CAS  Article  Google Scholar 

  56. 56.

    Lowry OH, Rosebrough NJ, Farr AL, Randall RJ. Protein measurement with the Folin phenol reagent. J Biol Chem. 1951;193:265–75.

    CAS  PubMed  Google Scholar 

  57. 57.

    Montplaisir D, Daneault C, Chabot B. Surface composition of grafted thermomechanical pulp through XPS measurement. BioResources. 2008;3(4):1118–29.

    Google Scholar 

  58. 58.

    Li Y, Qi B, Luo J, Wan Y. Effect of alkali lignins with different molecular weights from alkali pretreated rice straw hydrolyzate on enzymatic hydrolysis. Bioresour Technol. 2016;200:272–8.

    CAS  PubMed  Article  Google Scholar 

  59. 59.

    Gessner A, Waicz R, Lieske A, Paulke B, Mäder K, Müller RH. Nanoparticles with decreasing surface hydrophobicities: influence on plasma protein adsorption. Int J Pharm. 2000;196(2):245–9.

    CAS  PubMed  Article  Google Scholar 

  60. 60.

    Xu Y, Li F, Wang X, Yong Q, Yu S. Simultaneous separation and quantification of linear xylo- and cello-oligosaccharides mixtures in lignocellulosics processing products on high-performance anion-exchange chromatography coupled with pulsed amperometric detection. BioResources. 2013;8(3):3247–59.

    Google Scholar 

  61. 61.

    Overend RP, Chornet E, Gascoigne JA. Fractionation of lignocellulosics by steam-aqueous pretreatments. Philos Trans R Soc Lond A Math Phys Eng Sci. 1987;321(1561):523–36.

    CAS  Article  Google Scholar 

  62. 62.

    Seesuriyachan P, Kawee-ai A, Chaiyaso T. Green and chemical-free process of enzymatic xylooligosaccharide production from corncob: enhancement of the yields using a strategy of lignocellulosic destructuration by ultra-high pressure pretreatment. Bioresour Technol. 2017;241:537–44.

    CAS  PubMed  Article  Google Scholar 

  63. 63.

    Surek E, Buyukkileci AO. Production of xylooligosaccharides by autohydrolysis of hazelnut (Corylus avellana L.) shell. Carbohydr Polym. 2017;174:565–71.

    CAS  PubMed  Article  Google Scholar 

Download references

Authors’ contributions

PW and TZ designed the project, carried out the experiments, analyzed the data, and drafted the manuscript. ZL conducted the experiment on the determination of XOS. JW reviewed it. JZ designed and coordinated the overall study and finalized the paper. All authors read and approved the final manuscript.


Not applicable.

Competing interests

The authors declare that they have no competing interests.

Availability of supporting data

All relevant data have been included in this published article and its Additional file 1.

Consent for publication

All the authors approved the manuscript.

Ethics approval and consent to participate

Not applicable.


This work was supported by the National Key R&D Program of China (No. 2017YFD0601001) and the Natural Science Foundation of China (No. 31670598).

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Author information



Corresponding author

Correspondence to Junhua Zhang.

Additional file

Rights and permissions

Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (, which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver ( applies to the data made available in this article, unless otherwise stated.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Wen, P., Zhang, T., Wang, J. et al. Production of xylooligosaccharides and monosaccharides from poplar by a two-step acetic acid and peroxide/acetic acid pretreatment. Biotechnol Biofuels 12, 87 (2019).

Download citation


  • Poplar
  • AC pretreatment
  • HPAC pretreatment
  • Lignin removal
  • Xylooligosaccharides
  • Enzymatic hydrolysis