Structural studies of NiTe2 thin films with the influence of amino additives
Nickel, one of the transition metals synthesised with chalcogenides such as Se, S and Te with possible combinations of nickel chalcogenides such as NiS2, NiSe, NiSe2 and Ni3Se2. The combination of nickel and telluride are the fewest being observed due to the nature of tellurium that is relatively heavier than both sulphur and selenium, thus poorly-adhesive onto the substrate.
Therefore, NiTe2 thin film is being synthesised onto the indium tin oxide (ITO) coated glass substrates with the complex additives (Triethanolamine, TEA and ethylenediaminetetraacetic acid, EDTA) and their properties are studied. The present work is focusing on the NiTe2 synthesise through electrochemical route.
Cyclic voltammetry experiments have been done prior to electrodeposition in order to get the electrodeposition potential range. The observable reduction range is between −0.9−(−1.1) V with 5−10 min induction period of full thin film distribution depending upon the electrolyte conditions.
The electrodeposition is carried out using the potentials in the reduction region, producing the well-adherent, well-distributed and dark-coloured thin films. Structural studies confirm the presence of NiTe2 in electrolyte containing TEA with crystallite sizes lying on the 9−20 nm range.
KeywordsThin film Electrodeposition Additives Nickel telluride Structural studies
There are many synthesis routes of thin-film solar cells namely spray pyrolysis, pulsed laser deposition (PLD), chemical bath deposition, magnetron sputtering, molecular beam epitaxy and thermal evaporation which require the use of expensive machines, thus involving the high capital cost (Ilican et al. 2008; Patel 2012). Electrodeposition is introduced to cater the fabrication of thin films cost-effectively. Ability of large-scale deposition in complex shape, minimum waste of component and easy monitoring are among the advantages offered by this method (Shariza & Anand 2011; Anand 2009). Depending upon the type of additive, the film properties such as optical absorption, thermal stability, structure, morphology and adhesion onto the substrate has been studied (Junlabhut et al. 2013; Tayal et al. 2013; Vajargah et al. 2013; Anand & Shariza 2012). Solar cell is one of the promising alternative green energy sources that can provide free electricity when sunlight is converted. The absorbent materials and their synthesis methods are subject of interest mainly due to solar panel installation cost despite of free electricity generated. The well-known silicon solar cells made, either amorphous or polycrystalline, are good in conversion efficiency up to 17%, but their high cost drives the researchers to look for new materials (Xin et al. 2012). Semiconducting materials in thin film form such as InP, SnO2 and ZnO are being studied as the alternative materials, but are not commercialised due to their poor conversion efficiency. Another group of semiconductor compounds known as transition metal chalcogenides (TMC) have been developed to be used as the absorbent materials. Consisting of transition metals and chalcogenides (S, Se and Te), they show promising solar absorbent properties such as semiconducting band gap, good adhesion to substrate and good conversion with better cost-effectiveness. There are many TMC compounds synthesised, including copper indium selenide (CIS), CdS, CdTe, etc. (Balakrishnan & Muthusamy 2011; Radu et al. 2011).
Thin films referred as transition metal chalcogenides (TMC) have alternatively been used as the absorbent material for solar cells to replace the widely used silicon. Though many thin films of oxides, sulphides and selenide have been synthesised, only few studies of telluride thin films such as Bi2Te3, Hg1−xCdxTe, CdTe, CoTe and Ag2Te have been reported (Asokan et al. 2008; Peng et al. 2003; Sander et al. 2002). As one of the transition metal chalcogenides, nickel telluride, NiTe2, has been deposited in the form of thin film onto indium tin oxide (ITO)-coated glass substrates to be further developed into thin film solar cell. Though there is no reported literature about the use of NiTe2 to function as a solar cell, this has the high potential to be the candidate material of a solar cell. The syntheses of telluride thin films involve several techniques such as physical vapour deposition (PVD), metal organic vapour chemical deposition (MOCVD), solvothermal methods, coreduction method (in-situ) and electrodeposition (Peng et al. 2003). The PVD technique is excellent for good-quality film growth but is difficult to scale up (Anand et al. 2013a). The absorber layers for high-quality devices are typically synthesised via high vacuum deposition processes such as co-evaporation that is costly due to initial cost of equipment and production of vacuum (Ikeda et al. 2011).
Therefore, there is a great interest in developing non-vacuum, large-scale and low-cost technique such as electrodeposition (Anand et al. 2013a) for preparing NiTe2 thin films. Low-temperature processing results in the cost-effectiveness of this technique. Also, there is negligible waste of chemicals with better utilisation efficiencies. Semiconducting tellurides have great potential applications in optoelectronic devices including photovoltaic devices, light emitting diodes (LED), biological sensors and nanoscale electronics (Sander et al. 2002; Ling et al. 2010). NiTe2 in the form of nanorods were successfully synthesised through solvothermal method at temperatures (160°C and 180°C for 10 and 15 h, respectively) (Bin et al. 1999). Besides, NiTe2 nanoflakes and their self-assembled nanoflake arrays (1-D nanostructures) were prepared by a single-step hydrothermal method (Ling et al. 2010). The single-step electrodeposition is the most desirable way to simplify thin film fabrication, thus would be used to synthesise NiTe2 thin films (Anand et al. 2013a). The use of additives in thin film syntheses has been implemented where hexagonal NiTe2 nanoplates have been synthesised through an ethylenediaminetetracetic acid (EDTA)-assisted hydrothermal reaction and NiSe2 thin films have been obtained via triethanolamine (TEA)-assisted electrodeposition techniques (Liu et al. 2009; Anand et al. 2013b). In this paper, the preparation of NiTe2 thin films by the electrodeposition technique has been presented in different electrolyte conditions, deposition potential and deposition time with the use of both TEA and EDTA additives, separately. The effect of these additives has been thoroughly investigated prior to thin film characterisations.
The electrolytes prepared based on three different conditions
0.015 NiSO4·6H2O + 0.003 TeO2
0.015 NiSO4·6H2O + 0.003 TeO2 + 0.053
0.015 NiSO4·6H2O + 0.003 TeO2 +
Composition of additive
0.053 M EDTA
1.0 M TEA
Base (pH 10)
Acidic (pH 3)
Base (pH 10)
The cyclic voltammetry was run in the standard −2 to 2 V potential range with 30 min and 0.02 V/s being the time and scan rate, in order to get the most appropriate potential range of electrodeposition with respect to electrolyte conditions. The temperature was controlled to 40°C ± 2°C (Anand et al. 2013b). The first lower peak and subsequent upper peak of cyclic voltammograms represent the reduction and oxidation processes of the ions in electrolyte respectively. Once the potential range was obtained, the electrodeposition experiments had been conducted in three different electrolyte conditions as described in Table 1 in order to determine the optimum deposition potential and deposition time of NiTe2 thin-film electrodeposition.
The tabulation of additive concentration
Results and discussion
Cyclic voltammetry and optimum parameters of thin-film electrodeposition
The optimum additive concentration, deposition potential and deposition time
Deposition potential (V)
Deposition time (min)
0.015 M NiSO4·6H2O + 0.003 M TeO2
20 to 30
0.015 M NiSO4·6H2O + 0.003 M TeO2 + 0.026 M EDTA
5 to 30
0.015 M NiSO4·6H2O + 0.003 M TeO2 + 0.1 M TEA
10 to 30
A few electrodeposition experiments using EDTA in different concentrations revealed that the dark-grey film distribution was in good uniformity within the concentration range with 0.0265 M being the best EDTA concentration; however, the film adhesion started to become poor at 0.053 M and above. In the case of TEA, the optimum concentration was 0.1 M. Both 0.15 and 0.20 M TEA resulted in darker and poor-adherent films. On the contrary, the brighter films were acquired using 0.05 M TEA, but their adhesions were poor as well.
The comparison of ITO experimental ‘d’ values with its JCPDS data
(h k l)
(2 2 2)
(4 0 0)
(4 4 1)
(6 2 2)
Comparison of experimental ‘d’ values with JCPDS data for Ni3Te2(no additive, 30 min)
(h k l)
(1 1 1)
(2 0 0)
(2 2 0)
(3 1 1)
(2 2 2)
(4 0 0)
Comparison of experimental ‘d’ values with JCPDS data for Ni3Te2.07(with EDTA, 30 min)
(h k l)
(2 1 0)
(0 1 2)
(2 1 2)
(2 2 1)
Comparison of experimental ‘d’ values with JCPDS data for NiTe2(with TEA, 30 min)
(h k l)
(1 0 1)
(1 0 2)
(2 0 3)
It can be seen in Figure 3 that at all deposition potentials, the peaks of ITO are more prominent in intensity. At −1 V deposition time, the film peak intensities are at the highest, especially that of (220) and (311) planes at 2θ = 44.439° and 52.683°, showing that −1 V is the optimum potential at this particular electrolyte condition. ITO peaks at 2θ = 50.978 have shrunk at −0.9 and −0.1 V due to the growth of (311) plane films which has surmounted over the ITO. The interplanar distances ‘d’ corresponding to different h k l planes have been calculated from the X-ray diffractograms while the crystallite sizes are calculated from the measurement of full-width at half-maximum (FWHM) in different X-ray peaks, giving the values in the range of 9 to 20 nm.
Figure 4 shows the XRD patterns of non-stoichiometric nickel telluride, Ni3Te2.07 thin film deposited in the presence of EDTA corresponding to different deposition potentials. The peaks are identified as (210) and (212) planes of Ni3Te2.07. The structural features fit into the orthorhombic structure of the Ni3Te2.07 with lattice parameters values a = 0.7544, b = 0.3796 and c = 0.6073 nm which are in good agreement with the standard values (JCPDS, ICDD, Card No. 00-019-0847). Also, it can be seen that the film peak is relatively fewer at −1.0 V as compared to the ones at −0.9 and −1.1 V. The film peak intensity of (210) plane is the highest at −1.1 V suggesting that −1.1 V is the optimum potential at this electrolyte condition. The ITO peaks having (400), (441) and (622) planes show the observable decrease in intensity at each potential.
The film peaks matching the stoichiometric NiTe2 are detected in Figure 5 diffractograms. The peaks are identified as (101) and (102) planes of NiTe2. The structural features fit into the hexagonal structure of NiTe2 with lattice parameter values a = b = 0.3843 nm and c = 0.5265 nm which are in good agreement with the standard values (JCPDS, ICDD, Card No. 00-008-0004; Rotlevi et al. 2001). At 2θ = 31.704 at −0.9 V and 2θ = 43.917 at both −1.0 and −1.1 V, only one peak is obviously detected each with slightly higher intensity peak at −1.0 V, suggesting its optimum potential. The (400), (441) and (622) planes of ITO peaks relatively decrease at both −0.9 and −1.1 V.
Through the electrodeposition route, NiTe2 thin films have been successfully deposited onto ITO-coated glass substrates at −1.1 to −1.0 deposition potential range and 5 to 30 minutes deposition time. The presence of TEA in basic condition results in black-coloured and well-distributed stoichiometric films with good adhesion, enabling the optimum solar energy absorption as proven by structural studies and film appearance observation. It is found that the acidic electrolyte is not suitable for depositing NiTe2 thin films as proven by the inappropriate reduction range and poor adhesion of films.
The work described in this paper was supported by Universiti Teknikal Malaysia Melaka (UTeM) and FRGS / KeTTHA sponsored research grant (Project No. FRGS/2011/FKP/TK 02/1 F00120).
- Anand, TJS. (2009). Synthesis and characterization of MoS2 film for photoelectrochemical cells. Sains Malaysiana, 38, 85–89.Google Scholar
- Anand, TJS, & Shariza, S. (2012). A study on molybdenum sulphoselenide (MoSxSe2-x, 0 ≤ x ≤ 2) thin films: growth solution and its properties. Electrochimica Acta, 81, 64–73.Google Scholar
- Anand, TJS, Shariza, S, Rosli, ZM, & Thiru, S. (2013a). Optical and Mott-Schottky studies of ternary MoSSe thin films synthesized by electrochemical route. World Applied Science Journal, 21, 60–67.Google Scholar
- Anand, TJS, Zaidan, M, & Shariza, S. (2013b). Effect of additives on optical measurements of NiSe2 thin films. Procedia Engineering, 53, 555–561.Google Scholar
- Anuar, K, Saravanan, N, Tan, WT, Ho, SM, & Teo, D. (2010). Chemical bath deposition of nickel sulphide (Ni4S3) thin films. Leonardo Journal Science, 16, 1–12.Google Scholar
- Balakrishnan, K, & Muthusamy, D. (2011). Determination of optimum film thickness and composition of Cu(InAl)Se2 thin films as an absorber for solar cell applications. World of Journal Nanoscience and Engineering, 1, 108–118.Google Scholar
- Bin, L, Yi, X, Jiaxing, H, Huilan, S, & Yitai, Q. (1999). Solvothermal synthesis to NiE2 (E = Se, Te) nanorods at low temperature. Nanostructured Materials, 11, 1067–1071.Google Scholar
- Hesson, JR. (2012). Fundamentals of ultrasonic cleaning high energy sound supersonics. United States: Hessonic.Google Scholar
- Ilican, S, Caglar, Y, & Caglar, M. (2008). Preparation and characterization of ZnO thin films deposited by sol–gel spin coating method. Journal of Optoelectronics and Advanced Materials, 10, 2578–2583.Google Scholar
- JCPDS, ICDD. (ᅟ). PANalytical X’Pert HighScore. Card No. 00-019-0845.Google Scholar
- JCPDS, ICDD. (ᅟ). PANalytical X’Pert HighScore. Card No. 00-019-0847.Google Scholar
- JCPDS, ICDD. (ᅟ). PANalytical X’Pert HighScore. Card No. 00-008-0004.Google Scholar
- Junlabhut, P, Boonruang, S, & Pecharapa, W. (2013). Optical absorptivity enhancement of SiO2 thin film by Ti and Ag additive. Energy Process, 34, 734–739.Google Scholar
- Ling, J, Ying, JZ, & Jing, BC. (2010). Cetyltrimethylammonium bromide assisted self-assembly of NiTe2 nanoflakes: nanoflake arrays and their photoluminescence properties. Journal of Solid State Chemistry, 183, 2358–2364.Google Scholar
- Liu, X, Hu, R, Chai, L, Li, H, & Qian, Y. (2009). Synthesis and characterization of hexagonal NiTe2 nanoplates. Journal of Nanoscience and Nanotechnology, 9, 2715–2718.Google Scholar
- Radu, M, Ghenescu, V, Stan, I, Ion, L, Besleaga, C, Nicolaev, A, Mitran, TL, Tazlaoanu, C, Radu, A, Porumb, O, Ghenescu, M, Gugiu, MM, & Antohe, S. (2011). Photovoltaic properties of the CdS/CdTe heterojunction solar cells before and after proton irradiation. Chalcogenide Letters, 8, 477–485.Google Scholar
- Rotlevi, O, Dobson, KD, Rose, D, & Hodes, G. (2001). Electroless Ni and NiTe2 ohmic contacts for CdTe/CdS PV cells. Thin Solid Films, 387, 155–157.Google Scholar
- Shariza, S, & Anand, TJS. (2011). Effect of deposition time on the structural and optical properties of molybdenum chalcogenides thin films. Chalcogenide Letters, 9, 529–539.Google Scholar
This article is published under license to BioMed Central Ltd.This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly credited.