Microbiological quality of mink feed raw materials and feed production area
- 202 Downloads
The quality of mink feed and raw ingredients affect health and growth. The objectives of this study were to examine the microbiological quality of ready-to-eat mink feed and its raw ingredients, screen the plant part of the feed for mycotoxins, and determine the hygiene of the production environment in the feed processing facilities. The results of the study are important for identification of critical steps in the feed production and for formulation of recommendations for improvements of production processes to obtain better quality feed. Feed and swab samples were taken at three Danish mink feed producers October 2016 and May 2017, respectively. Viable counts, detection of methicillin-resistant Staphylococcus aureus (MRSA), influenza virus and filamentous fungi were performed together with qualitative chemical analyses for bioactive fungal metabolites and mycotoxins. Swab samples were analyzed for total viable counts.
Viable counts varied between 7.2 × 102 and 9.3 × 107 cfu/g in raw ingredients and between 107 and 109 cfu/cm2 on different surfaces at the feed production facilities. A pork meat product, pork haemoglobin, pork liver and a poultry mix was found positive for MRSA, while monophasic Salmonella [4,5,12:i:-] was detected in a pork meat product. Neither MRSA nor Salmonella was detected in any ready-to-eat feed. Influenza A virus was not detected in any sample. Filamentous fungi were detected in all analysed samples of ready-to-eat feed while dihydro-demethyl-sterigmatocystin was found in almost 50% of all ready-to-eat feed samples and in 80% of the sugar beet pulp. Fumonisins and other Fusarium toxins were found especially in corn gluten meal and extruded barley and wheat.
Mink feed contained a cocktail of mycotoxins and bacteria, which may not per se cause clinical disease, but may affect organ function and animal performance and well-being.
KeywordsAspergillus Clostridium Hygiene Influenza A virus Mink Mycotoxins
Denmark is the world’s largest producer of mink skins. The American mink (Neovison vison) is used for livestock production with 1248 commercial mink farms registered in 2018, which produced approximately 17.2 million mink skins (https://statistikbanken.dk). Feed factories supply the mink farms with pumpable wet feed consisting of a mix of animal by-products and slaughter offal (e.g. by-product from the fishing and meat industries) and plant origin (e.g. corn gluten meal, soybean oil and extruded cereals).
Raw ingredients of animal origin, mainly fish and poultry products and their by-products, are susceptible to bacterial contamination and spoilage. Likewise, ingredients of plant origin are susceptible to fungal spoilage and synthesis of mycotoxins. Spoilage microorganisms will always impair the quality, digestibility and the nutritional value of the feed and consequently, reduce not only the productivity of the animals, but also their health, behaviour and welfare. Limited work has been carried out to investigate the microbiological quality of mink feed. When analysing bacterial counts including enterococci, coliforms, haemolytic and sulphite-reducing bacteria in different raw materials, Juokslahti  reported high bacterial counts in fish by-product and blood meal with slaughterhouse by-product and unpreserved slaughter blood having the poorest quality.
The ready-to-eat feed may contain pathogenic or toxigenic bacteria, fungi and viruses originating from contaminated raw materials, which may cause diseases in the mink. Dietz et al.  described Salmonella Dublin-associated abortion in Danish mink and fox farms concluding that contaminated feed was responsible for the outbreaks. Other studies described uterine infections of mink caused by Clostridium limosum with suspicion of feed-borne transmission . Hammer et al.  reported a spontaneous outbreak of abortions and mortality in Danish mink farms probably due to C. limosum found in raw mink feed samples. Hansen et al.  found livestock-associated methicillin-resistant Staphylococcus aureus (LA-MRSA) in 20 out of 58 (34%) of clinical mink samples and in 20/108 (19%) of feed samples. Studies have shown mink to be sensitive to a number of mycotoxins, including aflatoxin B1, deoxynivalenol, zearalenone, fumonisins, moniliformin and ergot alkaloids . Bursian et al.  also showed that mink lost weight and developed kidney damage when fed ochratoxin contaminated feed. Aflatoxin-containing feed can cause poor skin quality, weight loss and kidney and liver damage , while deoxynivalenol (DON, vomitoxin) and other Type B trichothecenes have been demonstrated to cause emesis in the mink .
Analyses of medication and feed quality showed that the consumption of antibiotics increased when the numbers of faecal cocci were high [9, 10] although a direct association needs to be further verified. Poor feed quality may therefore indirectly lead to increased antimicrobial use. An earlier study of gastrointestinal disorders in mink found that differences between the feed producers as a risk factor accounted for 80% of the variation in occurrence of gastrointestinal disorders . Antibiotics are often used for treating unspecific diarrhoea or clinical pneumonia, and to a lesser extent in sporadic outbreaks of contagious diseases, such as Pseudomonas aeruginosa, and secondary infections after outbreak of mink influenza or canine distemper. However, resistance in the bacterial population is amplified by selection pressure from antibiotics use, which may result in reduced or—in worst case—no effect of the antibiotic treatment [12, 13].
Good quality of feed is essential for the animal performance, health and welfare. This applies to both nutritional value and microbiological quality. In the present study, we have focussed on the bacterial and mycological quality with the purposes to: (1) examine the microbiological quality of the raw ingredients (animal and plant origin) and the ready-to-eat mink feed; (2) screen the plant ingredients and ready-to-eat feed for mycotoxins and; (3) determine the hygiene level of the production environment in the feed processing facilities. The results may be important to identify any critical steps in the production of feed and may therefore be important to assist the feed factories in improving production processes to obtain better quality feed.
Collection and transport of the samples
Type of sample, analyses and total number of samples taken from three mink feed producers during October 2016 and May 2017
Type of analyses
Number of samples
Raw ingredients of animal origin
Detection of bacteria
Detection of influenza A virus
Detection of fungal metabolites and mycotoxins
Raw ingredients of plant origin
Detection of fungal metabolites and mycotoxins
Ready-to-eat feed I
Detection of bacteria
Detection of influenza A virus
Detection of filamentous fungi
Detection of fungal metabolites and mycotoxins
Ready-to-eat feed II
Detection of bacteria
In each sampling year, a total of 25 swab samples were taken from five different surfaces (10 × 10 cm) at all three feed producers. For transport to the laboratory, five swabs from the same surface were pooled to one subsample and placed into a sterile tube containing 10 mL of 0.9% NaCl (w/v) and 0.1% (w/v) peptone water and stored at 4 °C.
Detection of bacteria in samples of animal origin
Twenty-five gram of each raw feed ingredient of animal origin and of the ready-to-eat feed product (one pooled sample of five subsamples of 5 g each), respectively, were aseptically transferred to a Stomacher® 400 bag (Seward BA6041, Worthing, UK) containing 225 mL of 0.9% NaCl (w/v) and 0.1% (w/v) peptone water. The bag was blended in a Stomacher 400 Lab Blender (Seward Medical, London, UK) for 3 min. Tenfold serial dilutions were used for microbiological analyses. Total viable counts (TVC) were performed on spread plates with Plate Count Agar (PCA) (Thermo Fisher Scientific, Roskilde, Denmark) according to method ISO 4833-2:2012 . The number of Enterobacteriaceae was determined by pour plating in Violet Red Bile Glucose (VRBG) agar (Oxoid, Basingstoke, UK) according to the method of ISO 21528-2:2004 . Counts of clostridia were done by pour plating method on Tryptose Sulfite Cycloserine (TSC) agar (Oxoid) by the method ISO 7937:2004 (E) . Escherichia coli counts were determined on spread MacConkey agar plates (Thermo Fisher Scientific) using ISO 16649-2:2001 , except that we used MacConkey agar instead of 5-bromo-4-chloro-3-indolyl beta-d-glucuronide. The number of staphylococci were performed on spread plates with Baird-Parker agar (Thermo Fisher Scientific) according to the method of ISO 6888-1:1999 . All PCA plates were counted after 3 days’ aerobic incubation at 30 °C. Typical Enterobacteriaceae colonies were counted after 18–24 h aerobic incubation at 37 °C. Both MacConkey and Baird-Parker plates were counted after 18–24 h and 2 days, respectively, aerobic incubation at 37 °C. TSC plates were counted after 18–24 h anaerobic incubation at 37 °C.
From each ready-to-eat feed product, one subsample (ready-to-eat feed I) was immediately analyzed for bacteria as described before (t = 0). In order to simulate handling of the final feed product before mink may eat the feed, a second subsample (ready-to-eat feed II) was stored in the sampling container with lid open in room temperature overnight and analyzed the next day (t = 24).
For comparison of viable counts between seasons and feed factories, viable counts were log-transformed and hereafter compared using two-sided t-test.
For detection of Salmonella spp. , 25 g each of raw feed ingredient of animal origin and ready-to-eat feed (t = 0 and t = 24), respectively, were aseptically transferred into a Stomacher® 400 bag (Seward BA6041) containing 225 mL of buffered peptone water (BPW) (Thermo Fisher Scientific), then blended in a Stomacher 400 Lab Blender (Seward Medical) for 3 min and incubated at 37 °C for 16–20 h. Three drops (totaling 0.1 mL) of this BPW pre-enrichment culture were equally inoculated on Modified Semisolid Rappaport–Vassiliadis (MSRV) agar (Thermo Fisher Scientific) plates and incubated at 41.5 °C for 18–24 h. From MSRV, suspect growth was sub-cultivated on Brilliant Green Agar (BGA) (Thermo Fisher Scientific) and on Xylose Lysine Deoxycholate (XLD) Agar (Thermo Fisher Scientific). Similar to transferring BPW to MSRV plates, 1 mL of BPW was transferred into 9 mL Selenite Cystine (SC) broth (Thermo Fisher Scientific) and incubated for 18–24 h at 41.5 °C. From here, the BGA and XLD agar were inoculated. Suspect colonies from XLD and BGA were subcultured on Columbia agar plates containing 5% calf blood (SSI Diagnostica, Hillerød, Denmark) and verified by agglutination with polyvalent Salmonella serum (SSI Diagnostica).
Detection of methicillin-resistant Staphylococcus aureus (MRSA)
For detection of MRSA, raw feed ingredients of animal origin and of the ready-to-eat feed product were kept frozen until analysis. All samples were analysed by one-step enrichment, where 10 g were inoculated in 90 mL Mueller–Hinton Broth with 6.5% NaCl for 18–24 h at 37 °C without agitation. A loop-full (10 µL) enriched sample material was streaked on Brilliance MRSA2 agar (Oxoid) and incubated at 37 °C for 18–24 h. Presumptive MRSA colonies identified as denim blue colonies on MRSA2 agar were sub-cultured on agar plates (Oxoid) containing 5% calf blood for further verification. Isolates were identified as MRSA by PCR detection of the mecA and nuc genes .
Detection of filamentous fungi in ready-to-eat feed samples
For determination of filamentous fungi present in the feed, 1 g of thawed, ready-to-eat feed product was transferred directly to Dichloran 18% Glycerol agar (DG18 ()) and spread over the surface of the agar. Likewise, 1 g from each ready-to-eat product was plated onto vegetable juice agar (V8 ()). The plates were incubated in darkness at 20 °C and read after 5, 7 and 10 days. Representative fungi were isolated and inoculated onto different media for species identification according to Samson et al. . In brief: Aspergillus cultures were 3-point inoculated onto CYA, MEA and DG18 and incubated in darkness at 25 °C and CYA at 37 °C. Penicillium cultures were 3-point inoculated onto CYA, MEA and YES and incubated in darkness at 25 °C and CYA at 30 °C. Zygomycetes were 1-point inoculated on MEA, OA and DG18  and incubated in darkness at 25 °C and MEA at 30 °C.
Detection of bacteria in environmental samples
In the laboratory, 90 mL of 0.9% NaCl (w/v) and 0.1% (w/v) peptone water were added to each tube containing five pooled swabs and vortexed for 30 s. Tenfold serial dilutions were used for microbiological analyses. Total viable counts (TVC) were performed on spread plates with Plate Count Agar (PCA) (Thermo Fisher Scientific) as described above.
Detection of influenza virus A
RNA was purified from all raw feed ingredients of animal origin (except blood meal and pork fat) and from ready-to-eat feed. Liquid samples were pre-treated by lysing 200 μL of sample in 400 μL of RLT Buffer (QIAGEN) with 1% β-mercaptoethanol while solid samples were homogenized by beating on a Tissue lyser II (QIAGEN) to prepare 10% homogenate in RLT Buffer (QIAGEN) with 1% β-mercaptoethanol. RNA was purified from 600 μL homogenate/lysate using RNeasy Mini Kit (QIAGEN) on a QIAcube (QIAGEN) purification robot with protocol animal tissues and cells, large samples, version 2. The RNA was tested for influenza A virus using real-time RT-PCR directed against the matrix gene . In order to counteract possible PCR inhibition, the test was performed on both undiluted RNA and on RNA diluted tenfold in nuclease-free water.
Detection of mycotoxins and other bioactive fungal metabolites
Acetonitrile, methanol, formic acid and 25% ammonium hydroxide (LC–MS grade) and ethyl acetate were obtained from Sigma-Aldrich, Schnelldorf, Germany. Evolute express ABN SPE columns were obtained from Biotage, Sweden. Water was purified on a Milli Q system (Millipore Corporation, USA). Aflatoxin B1, B2, G1, and G2, citrinin, cyclopiazonic acid, deoxynivalenol, enniatin A1 and B1, fumonisin B1 and B2, nivalenol, ochratoxin A, patulin, sterigmatocystin, T2 toxin and zearalenone were all obtained from Sigma-Aldrich.
Sample material of 0.2 g (ready-to-eat feed or raw material) was transferred to a bead beater tube and added 1 mL 80% acetonitrile. After homogenization for 1 min the tube was cooled to 4 °C and centrifuged at 10,000×g. The supernatant was transferred to an Eppendorf tube and frozen at − 20 °C for 1 h followed by centrifugation at 10,000×g at 4 °C for 10 min. A SPE column (evolute express ABN 30 mg) was washed with 2 mL acetonitrile and dried and 0.3 mL of the supernatant was passed through the column and transferred to a HPLC vial.
Liquid chromatography quadrupole time-of-flight mass spectrometry
Liquid chromatography was performed on a Dionex Ultimate 3000 RS (Thermo Scientific) with a Poroshell SB C-18 column (100 mm length and 2.1 mm inner diam., 2.7 µm particle size) column held at 30 °C (Agilent Technologies, Walbron, Germany). The solvent system consisted of A: 2.5 mM ammonium hydroxide + 0.02% formic acid in water and B: methanol. Solvent programming were: 10% B at 0 min followed by a linear gradient to 45% B at 3 min and a linear gradient to 95% B at 14 min, isocratic 95% B from 14 to 16 min followed by reversal to initial conditions at 16.1 min and re-equilibration of the column to 20 min. The flow rate was 0.2 mL/min from 0 to 1 min followed by a linear gradient to 0.4 mL/min to 14 min, which was held until 16 min followed by reversal to initial conditions at 19 min.
The LC system was connected to a Bruker Daltonics, maXis qTOF mass spectrometer equipped with an electrospray ion source operated in positive ion mode (Bruker Daltonics, Bremen, Germany). The ion source settings were: nebulizer pressure 2 bars, drying gas flow 8 L/min, dry gas temperature 200 °C, and capillary voltage 4000 V. The scan range was from 30 to 1000 m/z with an acquisition rate of 2 Hz. Sodium formate dissolved in 50% 2-propanol was introduced in the ion source in a 0.2–0.4 min time segment and used for internal calibration of the data files. Hexakisperflouroethoxyphophazene was used as lock mass calibrant (Apollo Scientific, UK).
Fungal metabolite analyses
Data files were processed using Target Analysis (Bruker Daltonics). Based on information on the elemental composition of the analytes the software extracts ion chromatograms of the exact mass ± 3 mDa of aflatoxin B1, B2, G1, and G2, citrinin, cyclopiazonic acid, deoxynivalenol, enniatin A1 and B1 (ammonium adducts), fumonisin B1 and B2, nivalenol, ochratoxin A, patulin, sterigmatocystin, T2 toxin and zearalenone followed by integration of the chromatograms and reporting of the results.
The pH was determined from the first homogenate made for microbiological analysis by a Sartorius PB 310 Digital-pH-meter, Type PHM 92, (Radiometer, Analytical A/S, Copenhagen, Denmark).
The bacterial counts for each raw ingredient of animal origin and the ready-to-eat feed I and II from all three feed producers (A to C) in both sampling years 2016 and 2017 are shown in Additional files 1, 2, 3, 4, 5 and 6. Note that there are differences in sample categories between the years for the same producer.
In the raw ingredients from feed producer A in both sampling years 2016 and 2017, total viable count (TVC) between 1.8 × 104 and 9.3 × 107 colony-forming units/g (cfu/g) were found in most of the raw ingredients except in the fish silage (Additional files 1 and 4). In 2016, high Enterobacteriaceae counts were determined in raw ingredients from fish and pork products, but only low counts from poultry by-products (2.6 × 107 cfu/g) in 2017. In 2017, samples from poultry by-products and fish cut showed E. coli counts of 4.7 × 107 and 9.4 × 105 cfu/g, respectively (Additional file 4). In the same year, counts of staphylococci up to 2.4 × 106 cfu/g were detected in poultry by-products.
In 2016, TVC of all ingredients from feed producer B varied between 7.2 × 102 and 9.2 × 104 cfu/g (Additional file 2). In 2017, TVC of 1.3 × 104 and 5.4 × 104 cfu/g were found in fish cut and industrial fish, respectively (Additional file 5: Table S5).
In 2016, in all ingredients from feed producer C, TVC were between 2.6 × 103 and 3.8 × 104 cfu/g. In the same year, clostridial counts of 1.9 × 104 cfu/g were found in fish cut and of 4 × 104 cfu/g in poultry by-product (Additional file 3). In 2017, in blood samples all bacterial counts except clostridia were between 2.1 × 103 and 4.4 × 105 cfu/g (Additional file 6).
In both sampling years in all three feed producers, TVC of the ready-to-eat feed I varied between 9.8 × 104 and 1.1 × 107 cfu/g (Additional files 1, 2, 3, 4, 5 and 6). After storage overnight, TVC for the ready-to-eat feed II increased for all three producers to counts between 4.2 × 107 and 1.4 × 109 cfu/g.
Total viable counts of bacteria (cfu/cm2) from swab samples taken from the production facility at three feed producers (A–C) in 2016 and 2017
Feed producer (year)
Total viable bacteria (cfu/cm2)
5.5 × 105
4.6 × 104
Conveyor belt 620
4.6 × 108
Conveyor belt 810
1.5 × 105
Final product silo
1.7 × 109
Final product silo
1.5 × 103
Conveyor belt to homogenizer
4.5 × 102
Floor in room 1
2.7 × 106
5.0 × 108
Conveyor belt to chopper
3.5 × 107
1.5 × 109
1.8 × 109
Conveyor belt to silo
1.2 × 105
Final product silo 701
9.0 × 102
Final product silo 711
2.8 × 104
Conveyor belt 810
1.9 × 104
Conveyor belt 620
6.0 × 104
Distribution auger 626
5.0 × 102
1.3 × 103
2.3 × 103
4.0 × 107
6.0 × 102
2.9 × 103
1.0 × 102
1.8 × 105
2.0 × 102
7.2 × 102
The TVC were not statistically significantly different between seasons (autumn 2016 versus spring 2017) (P > 0.05). However, there was significant difference between feed factories, i.e. factory A had significantly higher counts than factory B and C, whereas there was no difference between B and C.
In 2016, pork meat product from feed producer A and in 2017, both haemoglobin and pork liver from feed producer A and poultry mix from feed producer B were positive for MRSA. In 2017, Salmonella Typhimurium monophasic variant [4,5,12:i:-] was detected in a pork meat product from feed producer A. Neither MRSA nor Salmonella were detected in the ready-to-eat feed from any of the three feed producers. All samples of raw ingredients and ready-to-eat feed were influenza-negative.
Fungal and mycotoxin analyses
Microbiological quality/fungal species present in samples of ready-to-eat feed from the three feed producers (A to C)
Absidia, Mucor, Rhizopus and Syncephalastrum species
A. niger, A. glaucus
P. discolor, P. polonicum
P. discolor, P. polonicum
M. racemosus, R. stolonifer
P. discolor, P. polonicum
M. racemosus, R. oryzae
A. flavus, A. glaucus
P. discolor, P. polonicum
A. niger, A. glaucus
Ab. corymbifera, M. racemosus
A. flavus, A. niger
P. discolor, P. polonicum
A. flavus, A. niger
Qualitative determination of mycotoxins and other biologically active metabolites present in samples of the different ingredients and ready-to-eat feed samples from the three feed producers (A to C)
Sample type (number of samples)
Other fungal mycotoxins/metabolites (number of samples)
Arbocel (n = 3)
Bio fiber (n = 1)
Corn gluten meal (n = 5)
Deoxynivalenol (2), Nivalenol (2), Zearalenone (3)
Extruded barley (n = 8)
Extruded wheat (n = 4)
Deoxynivalenol (1), zearalenone (1)
Plant silage (n = 2)
Soybean meal (n = 3)
Soybean oil (n = 4)
Sugar beet pulp (n = 5)
Blood meal (n = 2)
Haemoglobin (n = 1)
Meat product (n = 1)
Pigs fat (n = 2)
Ready-to-eat feed (n = 15)
The microbiological quality of feed is as important as the composition to ensure optimal growth and health of production animals. This study has shown that in both sampling years there is a great variety in bacterial counts between both similar and different types of raw ingredients and the three producers. Due to a continuous slaughter, by-products from slaughterhouses and the use of highly perishable raw ingredients like fish or poultry, these ingredients need preservation in order to maintain good microbiological quality when the feed is offered to the mink. Different treatments, like freezing (fish), heat treatment up to 90 °C (poultry) or acid treatment (silage of fish or spent laying hens) are used. However, high total viable counts (TVC) of bacteria up to 107 cfu/g were found in both fish and poultry ingredients. Juokslahti  reported high bacterial counts in fish by-product and unpreserved slaughter blood in a study from 1979. Although both cooling and hygiene for by-products may have improved since then, we still found high or moderate high bacterial counts in fish products and in haemoglobin and other blood products from pigs. The high moisture and nutrient content of fish and poultry-based ingredients are favoring the growth of microorganisms . Elevated temperature during transport and storage are likely the cause of the high bacterial counts of some ingredients seen in the present study. It is noteworthy that there were differences in viable counts between feed factories. It is not known whether this was due to differences in the quality of the raw materials the factories received or differences in procedures, such as treatment, transport or storage of raw materials and final products. Notwithstanding, the observation suggests that there is potential to improve the microbiological quality of the feed. This may be obtained by preventing growth of microorganisms or reducing their numbers e.g. using acidification or heat treatment, while others have suggested a beneficial effect of lactic acid fermentation .
To the authors’ knowledge, few studies have been published on the bacterial counts of freshly produced ready-to-eat mink feed products. When studying the effect of mink feed supplementation with sodium bentonite, Wlazlo et al.  reported TVC of 1.5–2.7 × 106 cfu/g in ready-to-eat products. During this study, TVC between 104 and 107 cfu/g were found in the ready-to-eat feed. When we simulated time/temperature procedures (corresponding to normal feeding of farm mink) of the ready-to-eat feed by storing sampling containers with lid open at room temperature overnight, TVC increased up to 1.4 × 109 cfu/g in ready-to-eat feed II. This result more or less corresponds to the bacterial concentration in a fully outgrown broth culture, and clearly shows the importance of maintaining the correct temperature of the ready-to-eat feed product during storage in the feed production facilities. Furthermore, bacteria can spread to the raw ingredients and ready-to-eat feed product during contact with contaminated feed handling equipment and storage containers. This condition applies not only to the feed producer, but also to mink farms, where cleaning and disinfection of feed silos and feeders should be included in daily routines. High bacterial counts of the environmental samples swapped from different surfaces at the feed production facilities with levels of 107 to 109 cfu/cm2 for TVC indicate low hygiene, poor cleaning and manufacturing practices. Thus, there is a risk of recontamination of raw ingredients and final ready-to-eat product by feed- and processing handling equipment and during storage. Several mink diseases caused by e.g. Enterobacteriaceae, E. coli, staphylococci and streptococci are caused by contaminated or spoiled feed .
Influenza A virus was not detected in the feed studied, but outbreaks of influenza in mink have previously been linked to feed as a potential source of infection . Gagnon et al.  isolated H3N2 influenza A virus from Canadian mink and speculated uncooked pork meat by-products obtained from slaughterhouse facilities to be the source of transmission. As far as known, influenza viruses have never been detected directly in feed. However, it may be quite difficult to detect influenza viruses in feed as viruses do not multiply in the feed the way that bacteria do, and since only a very small proportion of each feed portion was tested.
In the present study, LA-MRSA was only found in raw ingredients: pork meat product, pork haemoglobin, pork lever and poultry mix. All samples of ready-to-eat feed were LA-MRSA negative. Hansen et al.  reported LA-MRSA in 20/108 (19%) of final mink feed products. LA-MRSA was also widely found on the paws and in the pharynx of the mink, and spill-over from pig production via raw slaughter by-product was strongly suggested to be the source . In our case, all pork by-products were frozen and the poultry mix was heat treated when mixed into the final product. Salmonella Typhimurium was detected in a pork meat product, but not in the final products. Dietz et al.  concluded Salmonella Dublin-contaminated feed to be associated with an abortion storm in Danish mink and fox farms. Salmonella infections are zoonotic, which can lead to infections in both humans and animals. Our findings of pathogenic bacteria show that proper treatment and processing of raw ingredients are essential to reduce the risk of both the contamination of the ready-to-eat feed and a possible exposure to humans during handling the feed.
The results of the mycological analyses show that the ready-to-eat feed products were heavily contaminated with different fungal species, especially Zygomycetes, Penicillium and Aspergillus spp. Our results correspond well with a study on poultry feed, where Penicillium was the most frequent genus, followed by Aspergillus and Mucor .
Zygomycetes are fast growing, soil fungi  that produce up to 2 cm high hairy surface mycelium within days . Food- and feed-borne Zygomycetes are not known to produce mycotoxins or other bioactive fungal metabolites [32, 33]. However, their presence is suggestive of a poor hygiene in the production facility. Penicillium discolor was the most dominant species in the ready-to-eat feed products followed by P. polonicum. They both tolerate low temperatures, low pH values and low water activities  and are commonly found on nuts and cereals in temperate climates [21, 32]. Their presence suggests contamination of stored, processed cereals (e.g. barley or wheat). Aspergillus flavus together with A. niger and A. glaucus were found in samples collected in August and November 2016. These fungi thrive at higher temperatures and lower water activities than the Penicillium species and are common on stored cereals, and on nuts, beans and cereals grown in the tropics or subtropics [21, 32]. Aspergillus flavus and A. niger are known mycotoxin producers , but only dihydro-demethyl-sterigmatocystin and Fusarium mycotoxins were detected in this study. Their presence suggests contamination in the field and/or during storage of cereals (e.g. maize). A number of Fusarium toxins were also detected in the barley, wheat and maize raw ingredients. These metabolites are usually produced in the field during growth and remain after the field fungi have been replaced with storage fungi like Aspergillus and Penicillium. Sugar beet pulp, together with the extruded cereals and corn gluten seem to be the raw ingredients that are most susceptible to fungal contamination and thereby contribute the most to the overall mycotoxin content in the ready-to-eat feed.
The results of the chemical analyses show that 12 out of 25 ready-to-eat feed samples contained dihydro-demethyl-sterigmatocystin, a precursor to aflatoxin , possibly originating from contaminated maize gluten in the feed . Eight of the ready-to-eat feed samples also contained enniatins. These metabolites together with deoxynivalenol are produced by Fusarium species in cereals [21, 36] and may originate from either corn gluten or the extruded barley or wheat ingredients. The fungal metabolites detected in the ready-to-eat feed products may not in themselves be able to cause negative health effects in mink, but the additive or synergistic effects of fungal metabolites together with high amounts of bacteria in the feed may explain syndromes like wasting mink disease. There are some studies on mink and mycotoxins (e.g. aflatoxin and ochratoxin), but no studies on other biologically active metabolites (e.g. enniatins). On the other hand, there are several examples of pets that have become seriously ill after eating mycotoxin-containing feed products. Canadian dogs, which ate moldy foods containing penitrems A and roquefortine have died  while other dogs vomited, and developed diarrhea and liver failure after having eaten molded cereal products . Cats fed with T2 toxin, commonly found in moldy corn, contracted leukopenia (decreasing white blood cells), bloody stools and ataxia of the hind body . However, the above studies did not take any “cocktail effects” of either bacteria/mycotoxin or mycotoxin/mycotoxin into consideration in the complexity of the problem.
Mycotoxins make up only a small part of the many biologically active metabolites molds can secrete into mink feed. Different metabolites have different biological activity depending on dose: few are acute toxic, some have an estrogen-like effect, others cause liver and kidney damage and others again are carcinogenic. A group of fungal metabolites are also able to suppress the immune system , which leads to a higher risk of bacterial and viral infections, which in turn results in increased miscarriage and higher antibiotics consumption. It is therefore necessary to prevent and control both bacterial and mold contamination in both raw materials and final ready-to-eat feed products.
Frequent microbiological control is important as many raw ingredients of mink feed have a very high number of bacteria and fungi and thus a short shelf life. The analytical methods have a natural limitation, as the sample volume is very small compared to the total production volume and microbial or chemical hotspots can easily be missed. As the raw material composition is constantly changing, potential cocktail effects should be considered when introducing new types of raw materials. Bacteria and fungi can spread to feed through contact with contaminated feed-handling equipment and grow in storage containers. Proper cleaning of equipment and proper timing of handling, storage, processing of ingredients and of the final products are essential to guarantee a high quality feed and to prevent or control infections in mink as well as the risk of exposure to humans from handling of mink feed. This study has shown that ready-to-eat mink feed can contain a cocktail of mycotoxins and bacteria, which may not in themselves cause clinical disease in the animals, but which may affect the overall health and well-being of the mink. These synergies may play an important role for the appearance of new disease complexes with unknown etiology.
The authors would like to sincerely acknowledge the feed producers for their cooperation. We are grateful for the financial support from Dansk Pelsdyravlerforenings Forskningsfond. The authors wish to thank Anna Cecilie Boldt Eiersted, Annie Ravn Pedersen, Susanne M. Ranebro, Bojana Brinkmann Sörensen, Jannie Stjernholm, Lisette Knoth-Nielsen and Helle Ruby for their excellent technical assistance.
MC, UL and KP planned the study. MC performed the sampling. UL and BN did the bacteriology. BA and HF performed the fungal and mycotoxin analyses. CH did the detection of influenza virus A. UL, BA, HF and CH drafted the manuscript with contributions from MC, BN and KP. All authors read and approved the final manuscript.
This project was supported by a Grant from Dansk Pelsdyravlerforenings Forskningsfond.
Ethics approval and consent to participate
Consent for publication
The authors declare that they have no competing interests.
- 8.Wu W, Zhou HR, Bursian SJ, Pan X, Link JE, Pestka JJ. Comparison of anorectic and emetic potencies of deoxynivalenol (vomitoxin) to the plant metabolite deoxynivalenol-3-glucoside and synthetic deoxynivalenol derivatives EN139528 and EN139544. Toxicol Sci. 2014. https://doi.org/10.1093/toxsci/kfu166.CrossRefPubMedPubMedCentralGoogle Scholar
- 12.O’Brien TF. Emergence, spread, and environmental effect of antimicrobial resistance: how use of an antimicrobial anywhere can increase resistance to any antimicrobial anywhere else. In: Barza MD, Sherwood LG, editors. The need to improve antimicrobial use in agriculture: ecological and human health consequences. Chicago: The Chicago University Press; 2002. p. S78–S84.Google Scholar
- 14.ISO 4833-2:2013. Microbiology of the food chain—horizontal method for the enumeration of microorganisms—part 2: colony count at 30 °C by the surface plating technique.Google Scholar
- 15.ISO 21528-2:2004. Microbiology of the food chain—horizontal method for the detection and enumeration of Enterobacteriaceae—part 2: colony-count technique.Google Scholar
- 16.ISO 7937:2004. Microbiology of food and animal feeding stuffs—horizontal method for the enumeration of Clostridium perfringens—colony-count technique.Google Scholar
- 17.ISO 16649-2:2001. Microbiology of food and animal feeding stuffs—horizontal method for the enumeration of beta-glucuronidase-positive Escherichia coli—part 2: colony-count technique at 44 degrees C using 5-bromo-4-chloro-3-indolyl beta-d-glucuronide.Google Scholar
- 18.ISO 6888-1:1999. Microbiology of food and animal feeding stuffs—horizontal method for the enumeration of coagulase-positive staphylococci (Staphylococcus aureus and other species)—part 1: technique using Baird-Parker agar medium.Google Scholar
- 19.ISO 6579-1:2017 Microbiology of the food chain—Horizontal method for the detection, enumeration and serotyping of Salmonella—part 1: detection of Salmonella spp.Google Scholar
- 21.Samson RA, Houbraken J, Thrane U, Frisvad JC, Andersen B. Food and indoor fungi. CBS laboratory manual series 2. Utrecht: CBS-Fungal Biodiversity Centre; 2010.Google Scholar
- 24.Lindgren S. Storage of waste products for animal feed. In: Wood BJB, editor. The lactic acid bacteria, vol. 1. Boston: Springer; 1992.Google Scholar
- 25.Wlazło Ł, Nowakowicz-Dębek B, Fiołka M, Krukowski H, Zoń A, Trawińska B, Bryl M. The effect of sodium bentonite supplementation in the diet of mink (Neovison Vison) on the microbiological quality of feed and animal health parameters. Slov Vet Res. 2015;52:165–71.Google Scholar
- 26.Hildebrandt H. Bacterial diseases of mink. In: Merck veterinary manual. 2015. https://www.merckvetmanual.com/exotic-and-laboratory-animals/mink/bacterial-diseases-of-mink. Accessed 30th Jan 2029.
- 27.Larsen LE, Breum SØ, Trebbien R, Bradstad K, Nielsen LP, Chriél M, et al. Outbreaks of influenza A virus in farmed mink (Neovison vison) in Denmark: molecular characterization of the viruses. In: Proc. Xth Int. Scientific Congr. in Fur Animal Production: Scientifur 2012;36(3/4):153–6.Google Scholar
- 29.Hansen J. Methicillin-resistant Staphylococcus aureus in Danish production animals. Ph.D thesis, Technical University of Denmark, National Veterinary Institute, Lyngby; 2018.Google Scholar
- 31.Domsch KH, Gams W, Anderson TH. Compendium of soil fungi. 2nd taxonomy revised ed. In: Gams W, editor. Eching: IHW; 2007.Google Scholar
- 35.Battilani P, Costa LG, Dossena A, Gullino M. L, Marchelli R, Galaverna G, et al. Scientific information on mycotoxins and natural plant toxicants. EFSA Supporting Publications. 2009;6(9). https://doi.org/10.2903/sp.efsa.2009.en-24.
- 37.Naude TW, O’Brien OM, Rundberget T, McGregor ADG, Roux C, Flaoyen A. Tremorgenic neuromycotoxicosis in 2 dogs ascribed to the ingestion of penitrem A and possibly roquefortine in rice contaminated with Penicillium crustosum: clinical communication. J S Afr Vet Assoc. 2002;73:211–5.CrossRefGoogle Scholar
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The Creative Commons Public Domain Dedication waiver (http://creativecommons.org/publicdomain/zero/1.0/) applies to the data made available in this article, unless otherwise stated.