Amine-Aldehyde Chemical Conjugation on a Potassium Hydroxide-Treated Polystyrene ELISA Surface for Nanosensing an HIV-p24 Antigen
- 245 Downloads
The enzyme-linked immunosorbent assay (ELISA) has been widely used for disease surveillance and drug screening due to its relatively higher accuracy and sensitivity. Fine-tuning the ELISA is mandatory to elevate the specific detection of biomolecules at a lower abundance. Towards this end, higher molecular capture on the polystyrene (PS) ELISA surface is crucial for efficient detection, and it could be attained by immobilizing the molecules in the correct orientation. It is highly challenging to immobilize protein molecules in a well-aligned manner on an ELISA surface due to charge variations. We employed a 3-(aminopropyl) triethoxysilane (APTES)- and glutaraldehyde (GLU)-coupled PS surface chemical strategy to demonstrate the high performance with ELISA. A potassium hydroxide treatment followed by an equal ratio of 1% APTES and GLU attachment was found to be optimal, and a longer incubation with GLU favored maximum sensitivity. p24 is a vital early secreting antigen for diagnosing human immunodeficiency virus (HIV), and it has been used for efficient detection with the above chemistry. Three different procedures were followed, and they led to the improved detection of the HIV-p24 antigen at 1 nM, which is a 30-fold higher level compared to a conventional ELISA surface. The surface chemical functionalization shown here also displays a higher specificity with human serum and HIV-TAT. The above approach with the designed surface chemistry could also be recommended for disease diagnosis on other sensing surfaces involving the interaction of the probe and the analyte in heterogeneous test samples.
KeywordsEnzyme-linked immunosorbent assay Human immunodeficiency virus p24 antigen Amine-aldehyde Surface chemistry
Bovine serum albumin
Enzyme-linked immunosorbent assay
Human immunodeficiency virus
One optical density
Polyvinyl benzyl lactonoylamide
The detection of disease biomarkers and surface antigens on intact pathogens is necessary in the field of medical diagnosis to extend the human lifespan and to support healthier lives. Different detection systems are available to diagnose pathogens and life-threatening diseases, including cancers [1, 2, 3, 4]. The range of probes and sensing strategies has been shown to identify several diseases [5, 6]. Among these outcomes, the enzyme-linked immunosorbent assay (ELISA) is a well-established strategy for detecting and diagnosing major diseases including HIV, and ELISA has been considered as a quality control test [7, 8, 9, 10]. As an immunoassay, ELISA detects the antigen using the appropriate antibody. To fulfill this role, the antigen is immobilized on a polystyrene (PS) surface and then interacts with the partner antibody (primary antibody), followed by the host-specific antibody (secondary antibody) with the conjugated enzyme, which is allowed to bind to the primary antibody. Finally, these molecular interactions are monitored by a suitable substrate. Researchers have used different ELISA-based approaches, including the sandwich method with suitable poly- and monoclonal antibodies or aptamer-antibody combinations to improve the detections [11, 12, 13, 14].
The sensitivity of an ELISA depends on the parameters such as the interaction between the antigen and the antibody, the temperature, the pH, and the efficiency of the antigen attachment on the PS surface. Among these factors, the immobilization of the antigen or antibody on the PS plate plays a crucial role in improving the limit of detection. Moreover, the limitation posed by the attachment and the nonuniform distribution of protein on the PS surface highly affects the assay sensitivity . A higher quantity with the proper immobilization of protein aids in achieving the right orientation on the PS surface for possible improvements in detection. Different strategies have been employed to immobilize proteins properly on the PS surface. A protein or antibody has the ability to immobilize on the PS plate simply by chemical or physical adsorption or electrostatic interaction. Bora et al.  immobilized protein on the PS surface using photochemistry, and they found improvements of up to 1.5- to 2-fold higher compared to the untreated surface. In another study, the efficient immobilization of protein on the PS plate with a polymer called polyvinyl benzyl lactonoylamide (PVLA) was shown . Polyethylene glycol (PEG)-based polymers have also provided for the efficient immobilization of biomolecules on sensing surfaces. Lakshmipriya et al.  developed an improved detection of clotting protein factor IX by immobilizing its thiolated oligomer along with two polymers (PEG-b-PAAc and N6-PEG) on a gold-coated surface.
On the ELISA plate surface, PS is composed of an aliphatic carbon chain with pendant benzene rings on each carbon, and it provides a hydrophobic surface. The carboxyl group on the PS surface binds the antigen or antibody through an electrostatic interaction with its exposed amine groups. However, this binding strategy has disadvantages, such as the lower binding of protein and irregular positioning of the molecules. The smaller-sized proteins and peptides with a lower number of amino acid compositions are especially difficult to bind on the PS surface due to the availability of fewer epitopes. Furthermore, it has been shown that if the molecules on the sensing substrate are crowded, then the distance among the probes is too disturbed to engage in a genuine interaction. For that reason, increasing the binding of a protein or antibody on the PS plate with the proper orientation improves the detection limit. In general, proteins are directly immobilized on the ELISA surface, and researchers are focused on improving protein immobilization on the ELISA surface to develop high-performance detection. In particular, the immobilization of protein by chemical functionalization on the PS surface has been observed by several researchers to improve this strategy. Amine-based chemical modification is effective at immobilizing different antibodies through the appropriate cross-linker. 3-(Aminopropyl) triethoxysilane (APTES) is commonly used to modify the sensing surface for use with amines. The antibody can immobilize on the amine-modified APTES surface through its COOH group. However, the immobilization of protein cannot be linked directly onto the amine surface like the antibody; in particular, smaller-sized proteins require a proper cross-linking agent. Here, we introduced a simple step immobilization for protein using a chemical modification with APTES and glutaraldehyde (GLU). We immobilized the proteins covalently on the amine-modified surface and linked using GLU. GLU is an organic compound with the formula CH2(CH2CHO)2, and it has been found to be one of the most effective protein cross-linking agents [4, 18, 19, 20]. It has two aldehyde groups at its ends; one end binds with the amine-modified ELISA surface, and the other end is free to bind the protein or antibody. In general, the immobilization of smaller-sized proteins or peptides on the ELISA surface is truly challenging due to the presence of fewer amines on its surface. With the chemical functionalization strategy, there is a possibility of using smaller-sized proteins or peptides to immobilize the material strongly on the ELISA PS plate. For our method, we used APTES-GLU as the linker; by using this modification, we can immobilize any types of antibodies, proteins, and peptides. The signal and sensitivity enhancements under this strategy are higher compared to other chemical strategies explored in the past [3, 4].
To demonstrate the advantage of these chemistries, we chose the detection of one of the major human immunodeficiency virus (HIV) proteins (p24), which is expressed at the earlier stage of HIV infection. The p24 antigen is made up of the viral core and is present at a higher level during the first week of infection. Therefore, it is ideal to generate a sensitive system using p24 for earlier HIV detection. Herein, the detection of p24 was generated using the abovementioned chemically modified ELISA surface. This chemical functionalization strategy has improved the p24 detection on the PS ELISA surface over several folds, and it can be recommended for detecting other important clinical biomarkers.
Materials and Methods
Reagents and Biomolecules
Recombinant HIV-p24 and Tat proteins and p24 antibody were purchased from Abcam (Malaysia). 3-(Aminopropyl) triethoxysilane (APTES), glutaraldehyde (GLU), and human serum were purchased from Sigma-Aldrich (USA). Anti-mouse-IgG-conjugated horseradish peroxidase (anti-mouse immunoglobulin HRP) was obtained from Thermo Scientific (USA). An ELISA plate was procured from Becton Dickinson (France). An ELISA 5X coating buffer was obtained from Biolegend (UK). Bovine serum albumin (BSA) and HRP substrate [3,3′,5,5′-tetramethylbenzidine (TMB)] were obtained from Promega (USA). The analytical ELISA reader was obtained from Fisher Scientific (Malaysia).
Optimum APTES and GLU Levels for Functionalization on the PS Surface
The optimization of the APTES and GLU levels to use on the PS surface was performed with the targeted HIV p24 antigen. To decide the suitable concentrations of APTES and GLU, the ELISA surface was first activated by 1% potassium hydroxide for 10 min. Then, three different amounts of APTES (0.5, 1, and 2%) were allowed to bind on the ELISA surface, and they were incubated overnight at room temperature (RT). After that, two different amounts of GLU (1 and 2%) were applied to the amine-modified PS surface. At that point, HIV-p24 at a 250-nM concentration was allowed to bind on the GLU-modified surface, and the remaining GLU surface was blocked with 2% BSA. The p24 antibody was introduced at a 1:1000 dilution, and then anti-mouse IgG-HRP was allowed to bind to the p24 antibody. Finally, these interactions were monitored by adding the substrate (3,3′,5,5′-tetramethylbenzidine, TMB) for HRP. After the optimal amount of substrate (100 mM) was added, the absorbance was read with an ELISA reader at 405 nm. Control experiments were performed in the absence of target HIV-p24.
Optimization of Aldehyde Linkage to Amine Group
To determine the suitable incubation time for GLU to link the amine-modified surfaces, two different incubation times were observed. After the ELISA PS surface was modified with APTES, the GLU was immobilized for 3 h and independently incubated overnight, and then 250 nM HIV-p24 antigen was immobilized on the GLU-modified surfaces. The remaining steps were followed as shown in the previous experiment.
Comparative Detections Between HIV-p24 Antigen on the GLU-Modified Surface and the GLU Premixed-HIV-p24 Antigen Attachments
To detect the HIV-p24 antigen on the ELISA surface, we compared two different surface modification approaches using GLU. In the first one (method 1: amine-GLU-p24), the PS surface was initially modified by an amine using 2% APTES, 2% GLU was added to the surface to tether the plate surface with an aldehyde group, and then 100 nM HIV-p24 antigen was added. In the second approach (method 2: amine-GLU premixed p24), after the surface was modified by an amine, GLU-p24 (2% GLU was mixed with 100 nM of HIV-p24 antigen and maintained at RT for 30 min) was added. Finally, the detection was performed using the p24 antibody. The other steps were performed as explained above. The control experiments were performed in the absence of the target HIV-p24.
Detection Limit: Conventional vs Chemically Modified ELISA
To check the limit of detection, different concentrations of p24 were titrated from 0.5 to 500 nM, and they were evaluated using the conventional methods and methods 1 and 2.
HIV-p24 antigen was initially diluted with 1% ELISA coating buffer, added to the ELISA surface, and maintained at 4 °C overnight, and then the remaining areas were blocked with 2% BSA for 1 h at RT. After that, a 1:1000 dilution of p24 antibody was added and incubated for 1 h, and then a 1:1000 dilution of anti-mouse-IgG-HRP was added to the ELISA surface and allowed to stand for 1 h. Finally, the HRP substrate (TMB) was added and measured at a wavelength of 405 nm using the ELISA reader.
Different concentrations of HIV-p24 antigen were added to the APTES- and GLU-modified surfaces. After the antigen was immobilized, the remaining steps were followed as stated in the conventional ELISA. Washings were performed five times between each immobilization step. The absorbance was recorded at a 405-nm wavelength using the ELISA reader, and photographs were taken.
On the APTES-modified ELISA plate, different concentrations of p24 premixed with GLU were immobilized. All the other steps used for the conventional ELISA were followed. Washings were performed five times between each immobilization step. The absorbance was recorded at a wavelength of 405 nm using the ELISA reader, and photographs were recorded. Control experiments were performed in the absence of the target HIV-p24.
Specific Detection of the HIV-p24 Antigen on the APTES-Modified Surface
To check the assay specificity, we performed two different control experiments. Instead of the HIV-p24 antigen, we used human serum or HIV-TAT protein premixed with 1% GLU and added them to the APTES-modified surface. All the other steps were followed as explained above. Control experiments were performed in the absence of target HIV-p24.
Results and Discussion
Due to the higher genuine signal following the overnight incubation of GLU with the increased absorbance and specific detection of p24, we used a similar condition for further experiments. In this case, we immobilized the GLU on the APTES-modified surface and then attached the protein (method 1). We also tried another approach; first, we mixed 1% GLU with 125 nM HIV-p24 antigen and then added this mixture to the amine-modified PS surface (method 2). Surprisingly, there was an increased absorbance with the same concentration of HIV-p24 antigen (from OD 0.161 to 0.23) as the concentration used in method 2. When we allowed the protein to bind to the GLU as the premix, almost all the proteins were able to bind the GLU, and then this mixture easily adsorbed onto the amine-modified surface. However, when the protein was allowed to bind to the pre-immobilized GLU surface, most of the aldehyde groups of the GLU were not available. Figure 4b indicates that the mixing method shows the detection of a similar concentration (125 nM) of HIV-p24 antigen with a higher absorbance. Additionally, methods 1 and 2 displayed higher absorbance compared with the conventional method under the same concentration of HIV-p24 antigen.
To improve the limit of detection, we tried to premix GLU and the HIV-p24 antigen before the immobilization step on the APTES-modified surface. It was expected that the premixture of GLU and HIV-p24 antigen would improve with the greater immobilization of proteins on the ELISA surface. When we premix GLU with the HIV-p24 antigen, the binding ratio of aldehyde to GLU is high. When we add this mixture to the ELISA surface, it improves the immobilization rate. Dixit et al. found that when they premixed the antibody and APTES prior to immobilization on the ELISA plate, their approach enhanced the immobilization of the antibody on the ELISA surface and the limit of detection was increased . In our study, as expected, when we premixed the GLU and HIV-p24 antigen prior to immobilization, the limit of detection was improved to 1 nM and was 30-fold higher than that of the conventional ELISA, which showed a detection limit of 30 nM. Our strategy not only had an improved detection limit, but it also improved the absorbance for all the concentrations of HIV-p24 antigen. At 250 nM p24, we observed that the absorbance was 0.35, which is almost twice that of the conventional ELISA with the same concentration of HIV-p24 antigen. With all the HIV-p24 antigen concentrations, a large difference in absorbance was noted compared to the conventional ELISA (Fig. 5), as evident in the trustworthy detection of the HIV-p24 antigen.
A higher and proper immobilization of a protein or antibody on the ELISA surface dramatically improves the limit of detection. Here, we have introduced an interesting chemical functionalization method to immobilize the quantity of protein or antibody that binds on the ELISA PS surface, as assisted by APTES and GLU. To demonstrate detection, we used the p24 antigen from HIV. The limit of detection was improved by 30-fold compared with conventional ELISA. Further developments from the present investigation could lead to similar chemical-based improvements on other sensing surfaces and would be useful for detecting different antigens at a lower abundance, which would represent an advance in medical diagnoses.
We would like to thank Servier Medical Art.
Availability of Data and Materials
All the data are fully available without restriction.
The authors all contributed to the preparation of the manuscript and discussion. All the authors read and approved the final manuscript.
The authors declare that they have no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
- 18.Migneault I, Dartiguenave C, Vinh J et al (2004) Comparison of two glutaraldehyde immobilization techniques for solid-phase tryptic peptide mapping of human hemoglobin by capillary zone electrophoresis and mass spectrometry. Electrophoresis 25:1367–1378. https://doi.org/10.1002/elps.200305861 CrossRefGoogle Scholar
Open AccessThis article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.